Whiteメーカー21A-458B190の使用説明書/サービス説明書
ページ先へ移動 of 20
IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFUL L Y WHITE OUTDOOR PRODUC TS COMP ANY P .O. BOX 361 131 CLEVELAND, OHIO 44136-9722 REAR TINE TILLER MODEL RB650 21A-4 58B19 0 PRINTED I N U.
2 SECTION 1: FINDING YOUR MODEL NUMBER This Op erator’s Manual is a n imp ortant par t of you r new tille r. It wil l hel p you as sembl e, prepa re an d main tain your ti ller.
3 SECTION 3: IMPORTA NT SAFE OPERAT ION PRACTICES WARNING: THIS SYMBOL POIN TS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGE R THE PERSONAL SA FETY AND/OR PROPERTY OF YOURSELF A ND OTHERS. READ AND FOLLOW ALL INSTRUCTI ONS IN THIS MANUAL BEFORE ATTE MPTING TO OPERATE YOUR TILLER .
4 • Only use access ories approved for this mac hine by the manu facturer. Read, un derstand, and follow all ins truc tions provi ded w ith th e appr oved acce ss ory . • If situ ations occur which are no t covered by this manual, use care and good ju dgment.
5 SECT ION 4: LOOS E PARTS Handle Assembly Depth Stak e Assembly Control Rod NOTE: Cab le tie not show n..
6 SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped W ITHOUT GASOLINE or OIL. After assemb ly, see separat e engine ma nual for pr oper fuel and engine oil recomm endations. NOTE: Left and ri ght is det ermined f rom the operator’ s position, stand ing behin d the tiller .
7 Figure 5 A TT ACHING THE CLUTC H CABLE Attach the c lutch cable to the handle as foll ows (be careful no t to kink the cable). 1. Rou te the clutch c able to the left side of the till er, and under neath th e handle. Push the "Z" end of the cable in to the ho le in t he clut ch control bail.
8 Positio n the tiller s o the front counte rweight is against a solid object, suc h as a w all. Wit h the gear select ion lev er in NEU TRAL, sta rt the engi ne. Refer to the se parate eng ine ma nual. Standing on the ri ght side of the tiller , examin e the belt (i nside the belt cover) .
9 DEPTH ST AKE The depth ba r controls the till ing depth. Refer to SECTION 8: HOW TO USE Y OUR TILLER on page 9. HANDLE ADJUSTMENT (See Figure 8) The handl e may be adjuste d to be raised or lowered in line with th e tiller. To a djust the handle positio n loosen the handle height adjus tment cran k a few turns.
10 Figure 9 4. To tr ansport tiller, lowe r the depth s take (use to p adjustme nt hole). 5. To adj ust the depth stake, remov e the clev is pin and hair pin clip. See Figure 9. Move t he dept h stake to the desir ed setti ng. 6. To ad just th e side shields , remove th e fron t wing nut and lo osen the re ar wing n ut.
11 To adjust th e tension on the belt, refer to clu tch adjustm ent inform ation in “Chec king the Clu tch Adjustm ent” se ction of the Asse mbly Instruc tions. After be lt tensio n has bee n adju sted, if th e belt is excessi vely stretc hed, you m ay need to adjust th e idle r pul le y r o d.
12 BEL T REPLACEMENT CAUTION: Do not use an off-the-shelf belt. Your til ler has be en enginee red with a bel t made of specia l material (Kevlar Tens ile) fo r longer life and better p erformance . It shoul d not be r eplaced wi th an off-the- shelf belt.
13 SECTION 12: OFF-SEASON STORAGE If the till er will not be used for a per iod long er than 30 days , the followi ng steps sh ould be tak en to prepare th e tiller for storag e. 1. Cle an the exter ior of engine and the entir e tiller thorough ly. Lubric ate the tiller as desc ribed in the lu brication i nstruct ions.
14 Model 458.
15 Model 458 REF . NO. P ART NO. DESCRIPTION 1 61 1-0020 Wheel Shaft Ass’y: 33T 2 61 1-0021 Tine Shaft Ass’y: 18T 3 61 1-0128 Jack Shaft Ass’y 4 61 1-0129 Input Shaft Ass’y 5 617-0058 Rev .
16 Model 458 20 18 8 23 10 1 60 61 37 62 25 34 27 64 30 39 27 63 26 32 36 33 31 29 66 26 41 30 30 24 28 35 40 26 49 44 50 59 51 65 53 55 56 54 57 58 44 46 42 4 9 11 16 6 3 14 7 19 5 17 2 60 61 22 12 1.
17 Model 458 REF . NO. P AR T NO. DESCRIPTION 1 747- 1 152 S hift Rod 2 649-0033 Upper Ha ndle Ass’y 3 649-0 034 Low er Handle Ass’ y 4 710- 3005 Hex Scr ew 3/8 -16 x 1 .
18 Model 458 18 17 24 19 27 46 45 12 26 9 6 18 25 14 28 20 2 11 44 4 22 23 16 5 21 7 13 15 3 40 43 42 41 39 32 33 31 30 29 36 34 37 37 38 35 10.
19 Model 458 REF . NO. P ART NO. DESCRIPTION 1 686-01 1 1 Belt Cover Brk t. Ass’y 2 710-0237 Hex Bo lt 5/16-24 x . 62" Lg. 3 710-0412 Hex Bolt 1 /4-28 x .75" Lg. 4 710-0502 A Hex W ash.TT -Sems Screw 3 /8-16 x 1.25 0" Lg. 5 710-0591 Hex Bolt 3 /8-24 x 1.
20 MANUF ACTURER’S LIMITED W ARRAN TY FOR: For TWO YEARS from the date o f retail purch ase within th e United S tates of A merica, i ts posse ssions and te rritorie s, White Outdoor Products Comp a.
デバイスWhite 21A-458B190の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
White 21A-458B190をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWhite 21A-458B190の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。White 21A-458B190の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。White 21A-458B190で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
White 21A-458B190を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWhite 21A-458B190の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、White 21A-458B190に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWhite 21A-458B190デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。