WhiteメーカーRB650の使用説明書/サービス説明書
ページ先へ移動 of 20
IMPOR TANT: READ SAFETY RULES AND INSTRUCTIONS CAREFUL LY WHITE OUTDOOR PRODUCTS COM PANY P .O. BOX 361131 CLEVELAND, OHIO 44136-9722 REAR TINE TILLER MODEL RB650 21A-458B190 PRINTED IN U.
2 SECTION 1: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new tiller. It will help you assemble, prepare and maintain your tiller.
3 SECTION 3: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR TILLER.
4 • Only use accessories approved for this machine by the manufacturer. Read, understand, and follow all instructions provided with the approved accessory. • If situations occur which are not covered by this manual, use care and good judgment. Contact your dealer for assistance.
5 SECTION 4: LOOSE PARTS Handle Assembly Depth Stake Assembly Control Rod NOTE: Cable tie not shown..
6 SECTION 5: ASSEMBLY INSTRUCTIONS IMPORTANT: This unit is shipped WITHOUT GASOLINE or OIL. After assembly, see separate engine manual for proper fuel and engine oil recommendations. NOTE: Left and right is determined from the operator’s position, standing behind the tiller.
7 Figure 5 ATTACHING THE CLUTCH CABLE Attach the clutch cable to the handle as follows (be careful not to kink the cable). 1. Route the clutch cable to the left side of the tiller, and underneath the handle. Remove one hex nut and lock washer from the end of the casing on the clutch cable.
8 Position the tiller so the front counterweight is against a solid object, such as a wall. With the gear selection lever in NEUTRAL, start the engine. Refer to the separate engine manual. Standing on the right side of the tiller, examine the belt (inside the belt cover).
9 DEPTH S TAKE The depth bar controls the tilling depth. Refer to SECTION 8: HOW TO USE YOUR TILLER on page 9. HANDLE ADJUSTMENT (See Figure 8) The handle may be adjusted to be raised or lowered in line with the tiller. To adjust the handle position loosen the handle height adjustment crank a few turns.
10 Figure 9 4. To transport tiller, lower the depth stake (use top adjustment hole). 5. To adjust the depth stake, remove the clevis pin and hairpin clip. See Figure 9. Move the depth stake to the desired setting. 6. To adjust the side shields, remove the wing nuts.
11 To adjust the tension on the belt, refer to clutch adjustment information in “Checking the Clutch Adjustment” section of the Assembly Instructions. After belt tension has been adjusted, if the belt is excessively stretched, you may need to adjust the idler pulley rod.
12 BE LT REPLACEMENT CAUTION: Do not use an off-the-shelf belt. Your tiller has been engineered with a belt made of special material (Kevlar Tensile) for longer life and better performance. It should not be replaced with an off-the-shelf belt. If belt replacement is required, order belt or belts by part number from your nearest authorized dealer.
13 SECTION 12: OFF-SEASON STORAGE If the tiller will not be used for a period longer than 30 days, the following steps should be taken to prepare the tiller for storage. 1. Clean the exterior of engine and the entire tiller thoroughly. Lubricate the tiller as described in the lubrication instructions.
14 Model 458.
15 Model 458 RE F . NO. PART NO. DESCRIPTION 1 611-0020 Wheel Shaft Ass’y: 33T 2 611-0021 Tine Shaft Ass’y: 18T 3 611-0128 Jack Shaft Ass’y 4 611-0129 Input Shaft Ass’y 5 617-0058 Re v .
16 Model 458 12 15 12 12 22 2 60 61 5 17 19 1 60 61 11 6 16 14 4 9 3 7 20 8 18 10 23 37 34 62 25 27 64 30 39 26 63 32 36 33 31 27 29 26 41 42 46 44 49 44 26 40 30 24 35 28 21 50 59 58 51 65 53 55 56 5.
17 Model 458 RE F . NO. PART NO. DESCRIPTION 1 747-1152 Shift Rod 2 649-0033 Upper Handle Ass’y 3 649-0034 Lower Handle Ass’y 4 710-3005 Hex Screw 3/8-16 x 1.
18 Model 458 18 17 24 19 27 46 45 12 26 9 6 1 8 25 14 28 20 2 11 44 4 22 23 16 5 21 7 13 15 3 40 43 42 41 39 32 33 31 30 29 36 34 37 37 38 35 10.
19 Model 458 RE F . NO. PART NO. DESCRIPTION 1 686-0111 Belt Cover Brkt. Ass’y 2 710-0237 Hex Bolt 5/16-24 x .62" Lg. 3 710-0412 Hex Bolt 1/4-28 x .75" Lg. 4 710-0502A Hex Wash.T T -Sems Screw 3/8-16 x 1.250" Lg. 5 710-0591 Hex Bolt 3/8-24 x 1.
20 MANU FA CTURER’S LIMITED WARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, White Outdoor Products Company will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
デバイスWhite RB650の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
White RB650をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWhite RB650の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。White RB650の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。White RB650で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
White RB650を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWhite RB650の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、White RB650に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWhite RB650デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。