WindsorメーカーD250(115V) 10070100の使用説明書/サービス説明書
ページ先へ移動 of 25
Read these instructions bef ore operating the machine MOD EL: D250 (115V) 10070100 Beginning with Serial No. 1000054537 86038570 05/11/07 PRV NO. 98828 AB CARPET EXTRACTOR Operating Instru ctions (ENG.
TABLE OF CONTENTS D-250 86038570 05/11/07 1 Data Log/Table of Contents .................... 1 Safety Instructions ................................... 2 Grounding Instructions ............................ 3 Operations ..................................
SAFETY INSTRUCTIONS D-250 86038570 05/11/07 2 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use.
GROUNDING INSTRUCTIONS NOTE: In Can ada, th e use o f a tem p orary adaptor i s no t p ermit te d by the C anadia n Electri cal Co de PROPER GR OUND ING (115V) Meta l Sc r e w A daptor Grounded Out let Box Fig. A Fig. B Fig. C Tab For Gr ounding S crew Grounded Outlet Grounding P in A dapto r THIS PRODUCT IS FOR COMMERCI AL USE ONLY.
OPERATIONS D-250 86038570 05/11/07 4 CARPET INSPECTION: Determine precisely what areas you a re going to clean. Note problem areas in the carpe t or tack strip. Look for loose carpet, heavily damaged a rea s, discolored stains, or grease spots that will require prespotting.
OPERATION D-250 86038570 05/11/07 5 HEATER OPERATION The disconnect fittings o n the heater will become extremely hot during operation. Allow sufficient time to cool, or run solution through the machine with the heater turned off before disconn ecting the or performing any maintenance on the h eater.
MAINTENANCE D-250 86038570 05/11/07 6 DAILY MAINTENANCE: (At the end of each working day): 1. Flush the entire system, including floor t ool, hand tool, etc., with 1 to 3 gallons of clean, hot water. 2. Vacuum out the solution tank . 3. Rinse tank with fresh water.
MAINTENANCE D-250 86038570 05/11/07 7 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY QUARTERLY Check machine for cord damage * Check recovery dome an d gasket for damage and cleanliness * Check hose s f or.
MAINTENANCE D-250 86038570 05/11/07 8 ONLY QUALIFIED MAINTENANCE PE RSONNEL ARE TO PERFORM THE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEME NT 1. Turn off all switches and unplug machi ne. 2. Remove recovery tank. 3. Locate the vacuum motor wires and discon nect at the connector.
MAINTENANCE D-250 86038570 05/11/07 9 D-250 PUMP MAINTENA NCE Per manufacturer’s recommendatio ns the following main tena nce should be performed utilizi ng noted kits: 1.) 500 hours-Kit 86201080 – PRV NO. 250 -75A replaces the V-packing, wave washer, pa cking spreader a nd plunger guide.
TROUBLESHOOTING D-250 86038570 05/11/07 1 0 TROUBLE SHOOTING CHAR T PROBLEM POSSIBLE CAUSE SOLUTION No power to machine Dead electrical circuit Check building circuit breaker o r fuse box. Electrical shock Faulty power cord Replace. Equipment not grounding Follow grounding instructions exa ctly.
TECHNICAL SPECIFICATIONS D-250 86038570 05/11/07 11 TECHNICAL SPECIFICATIONS ELECTRICAL: 115 V, 60 Hz, 15 Amps per power cable ((D250 ) 230 V, 50 Hz, 15 Amps (D250IE) ELECTRIC VACUUM MOTOR (1) –2/1.25 HP, 2 stage, Waterlift –150” (381cm) SOLUTION PUMP 250 psi, adj.
NOTES: D-250 86038570 05/11/07 12.
RECOVERY TANK ASSEMBLY D-250 86038570 05/11/07 13 1 2 3 4 5 6 7 8 9 10 11 12 14 15 16 17 18 19 20 21 22 23 24 25 26 27 13 28 13 34 35 36 13 29 35 37 30 31 32 33.
RECOVERY TANK ASSEMBLY D-250 86038570 05/11/07 14 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86033260 05151 1 TUBE ASM, RECOVERY TANK 2 86242230 500009 1 LABEL, WARNING 3 86002620 2.
CONTROL PANEL GROUP D-250 86038570 05/11/07 15 5 4 6 2 18 19 3 9 1 16 11 13 17 10 8 12 14 7 15.
CONTROL PANEL GROUP D-250 86038570 05/11/07 16 REF PART NO. PRV NO. QTY DESCRI PTION SERIAL NO. FROM NOTES: 1 86199650 070-08 1 FAN 105 CFM AXIAL 2 86090870 61367 1 PANEL ASM, CONT.
VACUUM GROUP (LOWER) D-250 86038570 05/11/07 17 4 6 5 7 3 2 10 11 1 8 9 12.
VACUUM GROUP (LOWER) D-250 86038570 05/11/07 18 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86274980 70335 1 SCR, 10-32 X 1/2 PHTR GRN/GRND 2 86256480 70813 3 STUD, 14/20 X 3.
PUMP & HEATER GROUP (200 PSI) D-250 86038570 05/11/07 19 1 2 5 7 6 8 9 10 11 16 15 12 13 14 3 4.
PUMP & HEATER GROUP (200 PSI) D-250 86038570 05/11/07 20 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86199640 030-16 1 ELBOW, 1/4 NPT STREET LONG 90D 2 86200260 151-50C 1 HOSE, PULSE 47.
SOLUTION TANK ASSEMBLY D-250 86038570 05/11/07 21 10 11 13 12 14 16 8 7 6 11 25 24 5 4 27 1 26 29 28 2 3 1 11 12 23 17 18 19 15 30 35 16 36 37 12 33 34 32 36 20 22 11 12 9 20 21 39 38 40 40.
SOLUTION TANK ASSEMBLY D-250 86038570 05/11/07 22 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86201290 280-02 2 RIVET AL. 3/16 X 1/2 CLOSED 2 86201500 260-71 1 SOLUTION COVER D/B 3 8.
SPARE PARTS D-250 86038570 05/11/07 23 SUGGESTED SPARE PARTS PART NUMBER PRV NO. DESCRIPTION SERIAL NO. FROM 86199890 100-04A FUSE 3 AMP 200 PSI 86199240 250-33A BPR REPAIR KIT PUMPTEC 86201810 130-14.
115V WIRING DIAGRAM D-250 86038570 05/11/07 24.
デバイスWindsor D250(115V) 10070100の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Windsor D250(115V) 10070100をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWindsor D250(115V) 10070100の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Windsor D250(115V) 10070100の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Windsor D250(115V) 10070100で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Windsor D250(115V) 10070100を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWindsor D250(115V) 10070100の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Windsor D250(115V) 10070100に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWindsor D250(115V) 10070100デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。