WindsorメーカーModel Dの使用説明書/サービス説明書
ページ先へ移動 of 16
Handling, Installing and Operating Instructions Important Do not operate machine in unstable, low-flow range (surge). Read and become familiar with this manual prior to installing your Spencer Industravac equipment. Following the instructions detailed here will help you realize its full potential of efficient service and extended lifespan.
2 Contents Page I. W arranty 1 II. General Introduction 1 III. Getting Started 1 IV . Operation and Adjustments 7 V . Maintenance 7 Vl. T roubleshooting Guide — Separator 10 Vll.
3 Location Industravac vacuum producers are designed for operation at or near sea level atmospheric pressure and a nominal ambient temperature of 70°F (21°C).When necessary , they can be factory- designed for higher altitude or higher temperature operation.
4 Stationary Model. No special foundation is required. A level concrete floor or pad is recommended, although any other substantial floor is satisfactory .
Stationary Model Portable Model Stationary Model Portable Model 5 Series A Series B 2 1 / 4 cu. ft. DIRT CAN 2 1 / 4 cu. ft. DIRT CAN INLET EXHAUST DIFFUSER MANUAL BAG SHAKER 4" O.D. INLET INLET VA LV E MANUAL BAG SHAKER INLET V AL VE INLET V AL VE INLET V AL VE ST ARTER HANDLE 6" O.
6 Series C Series D Series V Stationary Model Portable Model INLET VA LV E MANUAL BAG SHAKER INLET INLET V AL VE INLET V AL VE INLET VA LV E 2-1/2 ” O.D. INLET MANUAL BAG SHAKER 2 1 / 4 cu. ft. DIRT CAN 2 1 / 4 cu. ft. DIRT CAN Stationary Model Stationary Model EXHAUST DIFFUSER ST ARTER HANDLE 4 1 / 3 cu.
7 V . Maintenance CAUTION: Disconnect electrical power before performing any maintenance procedure. 1. Lubrication 1. Motor . Follow motor manufacturer's recommendations. For following items 2 through 4, apply light lubricating oil yearly or more often as needed.
Reassembly (For Series V see Form ZZ) 1. Bolt the motor down tightly in its original position with the shaft in the exact center of the vacuum producer casing. Be sure that shims (if removed) are replaced in their exact positions on the same attach-points as before.
9 Balancing (For Series V see Form ZZ) T urn the machine on with inlet blocked to check balance. If there is excess vibration due to an unbalanced condition after reassemble, use the following balancing procedure: 1. Mark the position of the end impeller hub on the shaft.
10 Possible Cause • Worn or poorly fitting seals. • Holes worn in separator by abrasive materials. • Leaks. • Separator outlet blocked. • Dirt can liner sucked up against filter bag inlet. • Machine rotating backward. • Filter bags clogged.
11 Possible Cause VI. T roubleshooting Guide - V acuum Producer PROBLEM INSUFFICIENT AIR THROUGH SYSTEM MACHINE NOISY Corrective Action Change motor leads to correct rotation. Following instructions on pages 7-8, disassemble machine and reassemble correctly .
12 Possible Cause VI. T roubleshooting Guide - V acuum Producer (cont.) PROBLEM MACHINE VIBRA TING MOTOR HOT Corrective Action Clean impellers, check filter bags for holes. Straighten shaft. Replace bearing(s). Replace with correct motor . Disassemble machine, balance motor .
13 Filter Bag Part No. Filter Bag Maintenance Record Date Filter Bag Material Date Changed.
14 V acuum Accessories Record (Hoses, T ools, V alves) Part No. Description.
15 V acuum Cleaning Attachments and Accessories Catalog, Bulletin 241, contains Spencer ’s product line of professional cleaning components for use with portable and station- ary Industravac systems.
Industrially rated products offering effective solutions for air and gas moving problems: • Modular central vacuum systems • Mobile or stationary integrated vacuum units • Dust collectors and se.
デバイスWindsor Model Dの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Windsor Model Dをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWindsor Model Dの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Windsor Model Dの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Windsor Model Dで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Windsor Model Dを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWindsor Model Dの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Windsor Model Dに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWindsor Model Dデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。