WindsorメーカーSC326 10052220の使用説明書/サービス説明書
ページ先へ移動 of 31
Read these instructions before using the machine MODELS: SC326 10052220 SCC326 10052260 Operating Instructions 86039090 02/20/09 PRV NO. 98965 BE WALK BEHIND SCRUBBER IPX4.
MACHINE DATA LOG/OVERVIEW CUTTER 36V 86039090 04/03/07 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: ____________________ ___________________________________ .
TABLE OF CONTENTS CUTTER 36V 86039090 04/03/07 3 Machine Data Log/Overview. ........................ 2 Table of Contents .......................................... 3 HOW TO USE THIS MANUAL How to use this Manual. ................................ 1-1 SAFETY Important Safety Instructions .
HOW TO USE THIS MANUAL CUTTER 36V 86039090 04/03/07 1-1 This manual contains the f ollowi ng sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
CUTTER 36V 86039090 04/03/07 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors.
HAZARD INTENSITY LEVEL CUTTER 36V 86039090 04/03/07 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words - WARNI NG and CAUTION and FOR SAFETY.
SAFETY LABEL LOCATION CUTTER 36V 86039090 04/03/07 2-3 NOTE: These drawings indicate the location of safet y labels on the machine . If at any time the labels become illegible, promptly replace them. 2% GRADE WARNING SEE MANUAL CIRCUIT BREAKER DECAL 86243610 PRV NO.
TECHNICAL SPECIFICATIONS CUTTER 36V 86039090 04/03/07 3-1 ITEM DIMENSION/CAPACIT Y Nominal power 2160 W Rated Voltage 36 Volt DC Rated Amperage 60 amps Batteries 6 x 6 volt 250-305-335 AH @ 20 Hr rate Scrub Brush Motors 2 x .75 hp (.56 kW ) Vacuum Motor 3 Stage .
TECHNICAL SPECIFICATIONS CUTTER 36V 86039090 04/03/07 3-2 SPECIAL NOTES: The sound pressure level at the operator’s ear was measured to be 75 dBA. This was a nearfield, broad-band measurement taken in a typical industrial environment on a tile floor.
HOW THE MACHINE WORKS CUTTER 36V 86039090 04/03/07 The Saber Cutter is a battery powered, self- propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into the recovery tank.
COMPONENTS CUTTER 36V 86039090 04/03/07 3-4 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solution Strainer 10. Squeegee 11. Aqua-Mizer 12.
CONTROLS CUTTER 36V 86039090 04/03/07 3-5 3 5 1 7 6 13 11 10 4 2 9 12 8 14 15.
CONTROLS CUTTER 36V 86039090 04/03/07 3- 6 1. Key Switch 2. Emergency Shut-Off Switch 3. Speed Control Knob 4. Propel Control Lever 5. Reverse Button 6. Brush Switch 7. Brush Lift Lever 8. Solution Control Knobs 9. Vacuum Switch 10. Squeegee Lift Lever 11.
CONTROLS CUTTER 36V 86039090 04/03/07 3-7 7. BRUSH PRESSURE LEVER Adjusts the amount of brush pressure to the floor by raising or lowering the scrub d eck. To apply brush pressure, lower brush pressure lever to floating position. To apply additional pressure, place lever in restricted position.
CONTROLS CUTTER 36V 86039090 04/03/07 3-8 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicate full charge. Bars flashing near the left side indicate the batteries should be recharged.
MACHINE OPERATION CUTTER 36V 86039090 04/03/07 3-9 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performanc e or lost time from breakdown. Follow the same procedure each time to avoid missing steps.
MACHINE OPERATION CUTTER 36V 86039090 04/03/07 3-10 NORMAL SCRUBBING Plan the scrubbing pattern in advance. The longest track is around the perimeter of the area to be cleaned. For efficient operation, the runs should be the longest possible without turning, stopping, or raising and lowering scrub deck/squeegee.
MACHINE OPERATION CUTTER 36V 86039090 04/03/07 3-11 DOUBLE SCRUB For floors which are heavily soiled or h ave thick accumulations of floor finish may not clean sufficiently with one pass.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 50 HRS 100 HRS 200 HRS Check batteries after cha rging; add water if necessary * Check pad wear to preven.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-2 1. Batteries 2. Squeegee 3. Aqua Mizer 4. Scrub Brushes 5. Recovery Tank Float Shut-Off 6. Solution Strainer 7.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-3 1. BATTERIES The batteries provide the power to ope rate the machine. The batteries require regul ar maintenance to keep them operating at peak efficiency. The machine batteries will hold their charge for long periods of time, but they can only be charged a certain number of times.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-4 CHECKING BAT TERY SPECIFIC GRAVITY Use a hydrometer to chec k the battery specific gravity. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, the readi ng m ay not be accurate.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-5 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machi ne. FOR SAFETY: When charging, conn ect the charger to the batteries before conne cting the charger to the AC wall outlet.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-6 2. SQUEEGEE BLADES The front squeegee blade allows solution to pass through channels in the blade into the squee gee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4- 7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeege e and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine. Do not allow machine to roll back.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-8 4. SCRUB BRUSHES There are four different types of brushes available to cover applications from cle aning heavily soiled floors to polishing. A pad driver is also available to take advantage of the many cleaning pads on the market.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-9 ! WA RNI NG 6. SOLUTION STRAINER The solution strainer is located in front of the left front wheel. The solution strainer protect s the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-10 ! WA RNI NG 8. TRACTION MOTOR Do not use a pressure washer to clean around the motors. Use tap pressure only . TRACTION MOTO R CARBON BRUSH REPLACEMENT FOR SAFETY: Before leaving or servicing m achine, stop on a level surface, turn off machine and remove key.
MAINTENANCE CUTTER 36V 86039090 04/03/07 4-11 11. VACUUM MOTOR (Refer to the Vacuum Group in the parts se ction of manual) Do not use a pressure washer to clean around the vacuum motors. Use tap pressure onl y. Care must be taken so that water is not directed into vacuum motor air intakes.
MACHINE TROUBLESHOOTING CUTTER 36V 86039090 04/03/07 4-12 PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Worn squeeg.
MACHINE TROUBLESHOOTING CUTTER 36V 86039090 04/03/07 4-13 PROBLEM CAUSE SOLUTION Little or no solution flow to the floor Solution tank empty Fill solution tank Solution flow turned off or set too low .
デバイスWindsor SC326 10052220の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Windsor SC326 10052220をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWindsor SC326 10052220の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Windsor SC326 10052220の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Windsor SC326 10052220で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Windsor SC326 10052220を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWindsor SC326 10052220の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Windsor SC326 10052220に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWindsor SC326 10052220デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
