WindsorメーカーSP20-10090310の使用説明書/サービス説明書
ページ先へ移動 of 33
MODELS: U17-10090580 SP13-10 090220 SPT17-10090370 SP17IE-10090270 U20-10090600 SP15-10 090230 SPT20X-10090380 SP17IA-10090260 U17X-10090590 SP17-10 090240 SP17XIE-10090300 U20X-10090610 SP20-10 09031.
MACHINE DATA LOG/OVERVIEW 86309580 FLOOR POLISHER 10/08/0 8 2 Model: Date of Purchase: Serial Number : Sales Representative: Address: Phone Number:.
TABLE OF CONTENTS 86309580 FLOOR POLISHER 10/08/0 8 3 Machine Data Log. ............................ 2 Table of Contents .............................. 3 HOW TO USE THIS MANUAL How to use this Manual. .................... 1-1 SAFETY Important Safety Instructions .
HOW TO USE THIS MANUAL 86309580 FLOOR POLISHER 10/08/0 8 1-1 This manual contains the f ollowin g sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
SAFETY 86309580 FLOOR POLISHER 10/08/0 8 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors.
SAFETY 86309580 FLOOR POLISHER 10/08/0 8 2 - 2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard in tensity identified by signal words – WARN ING and CAUTION and FOR SAFTEY.
SAFETY 86309580 FLOOR POLISHER 10/08/08 2 - 3 GROUNDING INSTUCTIONS-120V THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power ci rcuit. The amp, hertz, and voltage are listed on the data label found on each machine.
SAFETY 86309580 FLOOR POLISHER 10/08/0 8 2 - 4 GROUNDING INSTRUCTIONS-230V THIS PRODUCT IS FOR COMM E RCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
SAFETY 86309580 FLOOR POLISHER 10/08/08 2 - 5 SAFETY LABEL LOCATION NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement.
TECHNICAL SPECIFICATIONS 86309580 FLOOR POLISHER 10/08/0 8 3 - 1 ITEM DIMENSION/CAPACITY/MODEL CONSTRUCTION Heavy-duty die cast aluminum deck with heavy- duty rubber bumper, tubular steel adjust able handle with die cast alumin um handl e housing MOTOR 1HP 115V induction SP13, SP15, SP17, U17, SP17, SP20, U20 1.
HANDLE INSTALLATION 86309580 FLOOR POLISHER 10/08/0 8 3-2 The handle must be installed by qualifi ed personnel. Read all instructions thoroughly. The machine is shipped with handle unassemble d. The machine is shipped wit h handle unassembled. Follow these steps for installation: 1.
OPERATION 86309580 FLOOR POLISHER 10/08/0 8 3 - 3 CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. 3. Adjustment Handle – Allows the handle to be adjusted to a comfortable operating position.
OPERATION 86309580 FLOOR POLISHER 10/08/0 8 3-4 MACHINE OPERATION For indoor use only. When using the pad, al ways keep the machine moving when in contact with the floor. High starting torque. Hold machine firmly with both hands. 1. Ensure that the pad driver is in good shape.
NOTES: 86309580 FLOOR POLISHER 10/08/0 8 3-5.
MAINTENANCE 86309580 FLOOR POLISHER 10/08/0 8 4-1 SCRUB BRUSHES NOTE: All original equipment brushes are equipped with “Perform Alert © ” . This feature will tell the operator when it is time to replace the scrub brushes. “Perform Alert © ” brushes ha ve pre-trimmed bright yello w tufts to indicat e the length of a worn out brush.
MACHINE TROUBLESHOOTING 86309580 FLOOR POLISHER 10/08/0 8 4-2 PROBLEM CAUSE SOLUTION Machine will not run Circuit breaker tripped in building. Check and reset. Power switch failure Test switch for continuity and replace if necessary. Tripped circuit breaker Reset.
NOTES: 86309580 FLOOR POLISHER 10/08/0 8 4- 3.
BRUSH/PAD DRIVER 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 1 3 3 1A-1E 1 2A-2W.
BRUSH/PAD DRIVER 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1A 86284280 02216 - PAD DRIVER, 13" POLISHER 1B 86284330 02396 - PAD DRIVER, .
ELECTRICAL-120V 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 3 14 A-C 3 1 2 4 6 7 8 9 10 11 12 13 5.
ELECTRICAL-120V 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86002010 14942 1 BOOT, 3/8 CIRCUIT BREAKER 2 86198450 20005 1 CLAMP, 5/16 NYLON 3 86234150 23167 1 CORD SET , 14/3 ST X 50FT , YLW 4 86216920 23206 1 C O R D S E T ,1 4 / 3X5 2I N ,S J T ,B L K 5 86268450 70689 1 SCR, M4.
ELECTRICAL-230V 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 5 14 A-C 3 A-B 1 2 4 6 7 8 9 10 11 12 13 5.
ELECTRICAL-230V 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 6 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86002010 14942 1 BOOT, 3/8 CIRCUIT BREAKER 2 86198450 20005 1 CLAMP, 5/16 NYLON 3A 86216950 23212 CORD SET, EURO 1.5MM X 75 BLK SP17HDIE, SP17IE, SPX17IE, SPDS17IE 3B 86216970 23217 CORD SET, SAA33 1.
DECK 86309580 FLOOR POLISHER 10/0 8/0 8/08 5 - 7 1 2A-2D 3 4 5 6 7 8 10 11 13 14 12 9A-9F.
DECK 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 8 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86214930 03111 1 AXLE, MAIN POLISHER 2A 86216350 14373 1 BUMPER, EXTRUSION 53.4 IN. SP13 2B 86216330 14371 - BUMPER, EXTRUSION 37.3 ” SP15 2C 86216340 14372 - BUMPER, EXTRUSION 43.
HANDLE 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 9 20 11 18 4 23 14 2 26 3 7 17 5 6 27 12 13 1 9 10 8 20 24 21 25 15 22 20 8 23 18 11 19 14 16.
HANDLE 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 10 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1 86215130 14344 1 BAR, HANDLE ADJUST 2 86216370 14434 1 BUMPER, BURNISHER HANDLE 3 86004070.
MOTO R 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 11 8 A-B 6 7 7 2 3 1 A-D 6 9 DUAL SPEED ONLY 5 4.
MOTO R 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 1 2 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES 1A 86312270 - 1 MOTOR, 1HP 115V INDUCTION SP13, SP15, SP17, U17, SPT17, SP20, U20 1B 86312280 - 1 MOTOR, 1.5HP 115V INDUCTION SP17X, U17X, SPT20X, SP20X, U20X 1C 86312300 - 1 MOTOR, 1HP 230V INDUCTION SP17IA, SP17IE 1D 86312310 - 1 MOTOR, 1.
WIRING-120V 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 1 3 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86311830 - 1 WIRE, 125MM, BLK/14, 76029X76029 M -MOTOR -CB1 -SWITCH -SWITCH 1 CORD .
WIRING –230V 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 1 4 REF PART NO. PRV NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 86311830 - 1 WIRE, 125MM, BLK/14, 76029X76029 M -MOTOR EMC FILTER2 EMC FI LTER -.
SUGGESTED SPARE PARTS 86309580 FLOOR POLISHER 10/0 8/0 8 5 - 15 PART NO. PRV NO. SERIAL NO. FROM NOTES: 86225710 87202 WASHER, BEARIN G (HANDLE ADJ) 86224740 73990 SPRING, EXT .5 OD X 3.5L 86224750 73993 SPRING, COMP .48 OD X .91 L 86007110 72123 SWITCH.
86309580 FLOOR POLISHER.
デバイスWindsor SP20-10090310の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Windsor SP20-10090310をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWindsor SP20-10090310の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Windsor SP20-10090310の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Windsor SP20-10090310で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Windsor SP20-10090310を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWindsor SP20-10090310の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Windsor SP20-10090310に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWindsor SP20-10090310デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
