WindsterメーカーRA.3130/3136の使用説明書/サービス説明書
ページ先へ移動 of 18
WINi:JS're~TM MODEL: RA.3030/3036 RA.3130/3136 OPERATION MANUAL c@~s 230302 Please read and save this guide through before using your range hood Store the guide away in a safe place so that you will know where it is. when you want to refer to it.
A. Important Safety Instructions Read and Save These Instructions CAUTION- To reduce risk of fire and to properly exhaust air. be sure to duct air outside- Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.
WARNING- To reduce the risk of injury to persons in the event of a range top grease fire. observe the following: A- SMOTHER FLAMES with a close- fitting lid. cookie sheet. or metal tray, then turn off the burner. Be careful to preven burns. If the flames do not go out immediately, EVACUATE AND CALL THEFIRE DEPARTMENT.
B. Safety Notes 1. All electrical work must be done in accordance with local and/or national electrical code as applicable for safety. This product must be grounded if your are unfamiliar with methods of installing electrical wiring, secure the services of a qualified electrician.
c. Tools and Materials Required ~ Drill. electric of ratchet drive. with 3/16" wood bit (for drilling starter holes and 1 ¥4 "wood bit (to drill an access holes in the cabinet or kitchen wall for the electric power line) ~ One common screwdriver.
E. Preparing The Range Hood 1. Remove the top electrical knockout. you may plan to bring power to the range hood either through the cabinet or through the wall (Fig.1) ~"~I Knooko", ~~~ ~ Fig. 2. Insert a screwdriver into the knockout slot and bend the knockou back and forth.
F. Preparing The Installation Location Note: Please also refer P.11 "J. Making the Electrical Connection' 1. A. If you want to move the electric range to make room for working on the cabinet turn off the 220 volt power for the electric range at the service entrance.
4. Screw the four 1" wood screws (tor mounting the hood) into the exact center of the arrow and of the keyhole mounting slots marked on the cabinet bottom (for flush installations), or marked on the 1 "x2" wood strips (tor recessed cabinet installation) (Fig.
Wiring to power supply & SAFETY WARNING RISK OF ELECTRICAL SHOCK. THIS RANGE HOOD MUST BE PROPERLY GROUNDED. MAKE SURE THIS IS DONE BY SPECIALIZED ELECTRICIAN IN ACCORDANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL CODES.
H. Mounting Range Hood To Cabinet Note: Please also refer P.11 "J. Making the Electrical Connection' 1. Position the hood in place so that: a. The electrical line is routed through the appropriate Knockout opening. This step will have to be accomplished while positioning the hood (Fig.
I. Mounting Range Hood Without Cabinet Note: Please also refer P.1 0 "J. Making the Electrical Connection' 1. Using metal brackets and screws (included), center hood onto board and install screw. 2. Remove the hood from the board and nail the wood board onto the wall.
J. Making the Electrical Connection 1. Turn the six nuts at the front/back of bottom board. ( Fig.13) 2. Remove screws on wiring case. fish out wires through the knockout. (Fig.13) screw Fig.! 3. Mark the electrical connection by fastening all wires to the existing wall wiring according to the their colors.
K. Use and Care Operate switches (Fig.9) ABC 0 I I I .... Switch A: I e I ON I OFF I DELAY Fig.9 "ON" - When the hood is "OFF", turn on the blower by press" . button once the blower will operate at second speed and LED light indicate "2", "OFF" - During operation, contiune to press" .
L. Halogen light replacement Note: The halogen light will be very hot when it is working Never touch it with bare hand(s). Before changing halogen light ensure the unit is switched off and the halogen light is cool. ~q B Q Note: Ensure the unit is switched off.
M. Maintenance Instruction 1. Maintenance shall be important than repair. Please take care of the needed maintenance in order to secure and extend the excellent functions and using life. Note: Before repairing the range hood. Disconnect the power source.
o. Parts Layout Diagram 15 ~~ -15- 1 Machine body 7 Chamber 13 Safety mesh 2 Control switch 8 Motor 14 Oilcollector (round) 3 Halogen light 9 Fan 15 Hanging bracket 4 Transformer 10 Oiltunnel 16 Inner.
P. Circuit Diagram NOTE: Any faults with this unit should only be attended to by a qualifiec technician. G)§@@ -16-.
Q. Size o Model: RA-3030 / RA-3036 o Model: RA-3130 / RA-3136 / RA-3142 / RA-314E -17-.
デバイスWindster RA.3130/3136の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Windster RA.3130/3136をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWindster RA.3130/3136の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Windster RA.3130/3136の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Windster RA.3130/3136で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Windster RA.3130/3136を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWindster RA.3130/3136の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Windster RA.3130/3136に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWindster RA.3130/3136デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
