WolfメーカーPro Wallの使用説明書/サービス説明書
ページ先へ移動 of 20
I NST ALLA TION I NSTR UCTIONS P RO W ALL C HIMNEY V ENTILA TION H OODS READ AND SA VE THESE INSTRUCTIONS.
As you follow these instructions, you will notice W ARNING and CAUTION symbols. This blocked information is important for the safe and efficient installation of Wolf equip- ment. There are two types of potential hazards that may occur during installation.
3 W OLF PRO W ALL CHIMNEY VENTILA TION HOODS Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION REQUIREMENTS IMPORT ANT NOTE: This installation must be completed by a qualified installer or W olf authorized service center technician.
4 W OLF PRO W ALL CHIMNEY VENTILA TION HOODS LIST OF MA TERIALS The following is a list of materials shipped with the W olf Pro wall chimney hood. Stainless steel wall chimney hood T ransition with ba.
5 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS ELECTRICAL REQUIREMENTS W olf Pro wall chimney ventilation hoods require a separate, grounded 110 / 120 V AC, 60 Hz power supply . The service should have its own 15 amp circuit breaker .
6 W OLF PRO W ALL CHIMNEY VENTILA TION HOODS INST ALLA TION SPECIFICA TIONS The illustration and chart below provides dimensions specific to each Pro wall chimney hood model.
7 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS DUCTWORK INST ALLA TION THROUGH ROOF 24" (610) DEPTH OF HOOD ROOF CAP OR REMO TE BLOWER 10" (254) ROUND DUCT SOFFIT OR CABINET OR DUCT CO VER NOTE: VERTICAL DISCHARGE ONL Y FOR PRO WALL CHIMNEY HOODS .
Existing W all Studs 2 x 4 Bloc king Back of W all Hood Outline 2" (51) 14" (356) 16" (406) 16¾" (425) Wood Mounting Strip 8 W ALL FRAMING IMPORT ANT NOTE: There must be a minimum 10" (254) opening in the ceiling to accommodate the ductwork necessary for proper ventilation.
9 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS HOOD PREP ARA TION Follow these steps to prepare the wall chimney hood for installation: Remove the filters by pressing up at the angle the filters are placed in, then rotate the bottom of the filter down.
10 W OLF PRO W ALL CHIMNEY VENTILA TION HOODS A CCESSORIES Optional acces- sories are available through your Wolf dealer . T o obtain local dealer information, visit the Locator section of our website, wolfappliance.
11 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS HOOD INST ALLA TION IMPORT ANT NOTE: If an optional duct cover is to be used with the Pro wall c.
12 W OLF PRO W ALL CHIMNEY VENTILA TION HOODS Do not remove the control knob bezel to access hood wiring; this will damage the bezel assembly . Location of wiring IMPOR T ANT NO TE Y ou must follow all National Electrical Code regulations. In addition, be aware of local codes and ordinances when installing your service.
13 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS INST ALL WIRING IN-LINE OR REMO TE BLOWER WIRING Remove the hood electrical box cover . Run power cable to the installation location. Insert the power cable into the electrical box by running it through the wire clamp previously installed.
14 W OLF PRO W ALL CHIMNEY VENTILA TION HOODS FIL TER INST ALLA TION Follow these instructions to install filters and grease cups for W olf Pro wall chimney hoods: Reinstall the internal frame. Refer to Hood Preparation on page 9. Remove all packaging material from the filters and grease cups.
15 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS Thre a ded S t u d s T op of Hood Intern a l Blower Hex He a d N u t s Pow e r Cord Thre a ded S.
Be sure that there is enough space for any transitions that may be needed between the blower and the connecting ductwork. For best performance, locate transitions nearest the blower . Refer to the illustrations below and on the following page for overall dimensions of W olf in-line and remote blowers.
17 Dimensions in parentheses are in millimeters unless otherwise specified. INST ALLA TION INSTRUCTIONS BLO WER ASSEMBLIES W olf Pro wall chimney ventilation hoods are shipped without the blower assembly . Wolf internal, in-line and remote blower assemblies are available as sales accessories through your W olf dealer .
18 W OLF PRO W ALL CHIMNEY VENTILA TION HOODS The information and images are the copyright property of Wolf Appliance, Inc., an affiliate of Sub-Zero, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Wolf Appliance, Inc.
19 CUT -OUT FOR LOGO PLACEMENT BO TT OM EDGE OF HOOD FOLD LINE FOR LOGO PLACEMENT LEFT OUTER EDGE OF HOOD.
810482 6 / 2007 WOLF APPLIANCE, INC. P . O . BO X 44848 MADISON, WI 53744 800-332-9513 WOLF APPLIANCE.COM.
デバイスWolf Pro Wallの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Wolf Pro Wallをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWolf Pro Wallの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Wolf Pro Wallの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Wolf Pro Wallで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Wolf Pro Wallを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWolf Pro Wallの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Wolf Pro Wallに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWolf Pro Wallデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
