WoodstockメーカーW2000の使用説明書/サービス説明書
ページ先へ移動 of 25
COPYRIGHT © 1995 BY WOODSTOCK INTERNATIONAL, INC., REG.# TX 3 360-515 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. PRINTED IN TAIWAN REPRINTED FEBRUARY 1999 P.
W2000 Rebel ® – 1 TABLE OF CONTENTS I. INTRODUCTION ..................................................................................................................................2 A. SAFETY INSTRUCTIONS FOR ALL TOOLS ...........................
2– W2000 Rebel ® For Your Own Safety, Read Instructions Before Using The Rebel ® A. Safety Instructions For All Tools These safety rules cannot cover every situation in a workshop. Consider your individual workshop conditions when setting up or operating any machine.
W2000 Rebel ® – 3 B. Additional Safety Rules For The Rebel ® 18. NEVER LEAVE THE TOOL RUNNING UNATTENDED - TURN POWER OFF. Do not leave the tool until it comes to a full stop. 19. DO NOT OPERATE THE TOOL IF USING DRUGS, ALCOHOL, OR MEDICATION. 20.
4– W2000 Rebel ® Woodstock International, Inc. is proud to offer the W2000 Rebel ® Router Table. The Rebel ® , named because of its radical design and construction features, is substantially different to what is currently available in the market place.
W2000 Rebel ® – 5 The Rebel ® is designed for heavy-duty use, yet it weighs only 35 pounds and is completely portable. However, when lifting, we must caution against improper lifting techniques. Always keep your back straight and lift with your legs.
6– W2000 Rebel ® Assembly of The Rebel ® is extremely straight forward and can be accomplished with just a few simple hand tools. In fact, the only tools you will need are a regular screwdriver, Phillips ® screwdriver, adjustable wrench, 3 ⁄ 16 " Allen ® wrench and a good quality straight edge.
W2000 Rebel ® – 7 Figure 4. Attaching the fence. The Rebel ® has a two-part, split fence designed for either straight-line or offset shaping. Assembling the fence is quite simple and straightforward.
8– W2000 Rebel ® The safety guard system consists of a clear plastic guard and arm which have been assembled at the fac- tory. There is also a height adjustment bar, mounting bracket with lock knob and bolt and washer.
W2000 Rebel ® – 9 Although the power switch on your router can be turned on and off each time you use The Rebel ® , the optional switch (Item Number W2001) offers greater convenience and safety. The optional switch is avail- able through your retailer.
10 – W2000 Rebel ® If using the optional safety switch, make sure it is in the off position. You can now plug your router into the cord connected to the back of the switch.
W2000 Rebel ® – 11 A. Router Table Insert Located in the four corners of the insert ledge on the table are four holes. These holes are threaded to accept the 10-32 x 3 ⁄ 4 " setscrews provided. Figure 14 . The setscrews are turned in or out from underneath to adjust router table insert flush with the table.
12 – W2000 Rebel ® For applications where the entire edge of the work- piece is being shaped, the outfeed fence must be offset by the same amount of material that you are removing. Use a sample piece at least 12" long as a test piece. Read and follow all safety procedures covered in this manual before cutting a sample.
W2000 Rebel ® – 13 Figure 18. Fence alignment. Figure 19. Safety guard adjusted properly. For applications where an adequate bearing surface remains after edge shaping, the fences must be in a straight line in relation to one another. One of the eas- iest ways to do this is to remove the existing wood fac- ings and put on a one piece unit.
14 – W2000 Rebel ® Figure 20. Miter gauge. Step 6 - Adjust the 90° miter gauge stop bolt so it rests against the pin. Re-tighten the jam nut. Be careful not to alter the position of the stop bolt. Step 7 - Re-check the squareness of the miter gauge to the miter slot using your square.
W2000 Rebel ® – 15 A. Site Planning B. Working Height Although The Rebel ® is completely portable and can be set up and used just about anywhere, we would like to discuss some basic considerations. When choosing a location for The Rebel ® , ensure that there is adequate room for maneuverability and safety.
16 – W2000 Rebel ® D. General Operations The general operating procedures are just that: “gener- al in nature”. They are not the final word on perform- ing any one of the many functions that are possible with The Rebel ® .
W2000 Rebel ® – 17 E. Straight Edge Shaping Straight edge shaping requires the use of the fence assembly. Although many edge shaping router bits have a guide bearing, the fence should still be used to provide maximum support and safety during the rout- ing operation.
18 – W2000 Rebel ® G. Freehand Work The Rebel ® is ideally suited to performing freehand work. Freehand shaping enables you to profile the edge of curved or irregular shaped wood. In order to free- hand shape on The Rebel ® : The fence must be removed, a starting pin or starting block and a router bit with a guide bearing must be used.
W2000 Rebel ® – 19 Step 6 - Once the workpiece or fixture is contacting the guide bearing on the router bit, move the workpiece or fixture away from the starting pin or starting block and continue feeding against the guide bearing. Figure 27. It is important that you feed the work smoothly and evenly in order to reduce tear-out and burning.
20 – W2000 Rebel ® Figure 28. Stop block in position. H. Using Stop Blocks If a particular application requires that you precisely and consistently start and/or stop multiple workpieces at the same place, it may be beneficial to use stop blocks.
W2000 Rebel ® – 21 Because there are no moving parts, maintenance is vir- tually eliminated. However, we do make the following recommendations: • Give the table a shot of some type of protec- tive coating. Many types of machine table coatings are available on the market today.
22 – W2000 Rebel ® VI. Parts Breakdown.
W2000 Rebel ® – 23 VII. Parts List 1 TABLE TOP 2 LEG 3 PANEL 4 SIDE PANEL 5 CAP SCREW 1 / 4 "-28 X 5 / 8 '' 7 SETSCREW 10-32 X 5 / 8 '' 8 FOOT 9 FENCE 10 FENCE LOCK 11 FLAT.
24 – W2000 Rebel ® Woodstock International, Inc. (Woodstock) warrants this product against defects in workmanship and mate- rials under normal use and service for a period of one year. This warranty extends to the original purchaser from the date of purchase.
デバイスWoodstock W2000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Woodstock W2000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはWoodstock W2000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Woodstock W2000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Woodstock W2000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Woodstock W2000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はWoodstock W2000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Woodstock W2000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちWoodstock W2000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
