YamahaメーカーD5000の使用説明書/サービス説明書
ページ先へ移動 of 42
YDG2030 PROFESSIONAL DIGIT AL DELA Y OPERA TING MANUAL MANUEL D’UTILISA TION BEDIENUNGSHANDBUCH INPUT LEVEL -00 +10 LR DRY WET MIX LR CLIP -6 -12 -18 -24 -30 -36 -42 PROGRAM PROFESSIONAL DIGITAL DEL.
D5000 FCC INFORMA TION (U .S.A.) 1. IMPORT ANT NO TICE: DO NO T MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly appro ved b y Y amaha may void y our authority , granted by the FCC , to use the product.
Contents - 1 D5000 Contents Introduction .............................................................................................................. 2 Precautions .....................................................................................
2 - Introduction D5000 Introduction With its high-quality 20-bit sound, the Yamaha D5000 Professional Digital Delay is the perfect choice for studio and sound reinforcement applications. It has four types of effect programs: DUAL (stereo) delay, SINGLE (mono) delay, FREEZE record and playback, and S&H (sample and hold) playback.
Precautions - 3 D5000 Precautions Avoid excessive heat, humidity, dust, and vibration Keep the unit away from locations where it is likely to be exposed to high temperatures or humidity - such as near radiators, stoves, in direct sunlight, etc. Avoid locations which are subject to excessive dirt accumulation.
4 - The front panel D5000 The front panel 1 INPUT LEVEL – The two concentric rotary controls are used to adjust the level of the input signal. The inner control adjusts the left channel and the outer control adjusts the right channel. 2 MIX – This control adjusts the amount of effect from DRY (no effect) to WET (full effect).
The back panel - 5 D5000 The back panel 1 BYPASS or PROGRAM INC/DEC Footswitch Jack – The function of this jack is determined by the FOOT SW FUNCTION parameter of the UTILITY Mode. If it is set to BYPASS , the footswitch duplicates the function of the [BYPASS] key.
6 - System structure D5000 System structure The D5000 has three operational modes: • Program Select Mode - Use this mode to STORE and RECALL programs.
Program Select Mode - 7 D5000 Program Select Mode About the programs of the D5000 The D5000 has 100 user programs. All of the programs are user-programmable. There are four types of programs available: • DUAL (stereo) Delay (refer to the diagram on page 100) There are two delay units (A-channel and B-channel) and three taps for each unit.
8 - Program Select Mode D5000 Press the [ > ] " RECALL " CURSOR key. If you have not made any changes to the previous settings, it will be replaced with the new program.
Parameter Edit Mode - 9 D5000 Parameter Edit Mode The D5000 has four types of effect program. The first two are high-quality, multi-tap digital delays, either DUAL (stereo) or SINGLE (mono).
10 - Parameter Edit Mode D5000 Changing the TEMPO parameter Use one of the following methods to modify the TEMPO parameter: • Manual Input Select the parameter with the CURSOR keys, then modify the value by rotating the DATA ENTRY encoder.
Parameter Edit Mode - 11 D5000 Page 2 parameters Page 3: Setting the title and controller assignments Use this page to edit the name of your delay program. You can set two parameters that can be controlled by a MIDI device. These parameters are set for each individual program.
12 - Parameter Edit Mode D5000 Page 3: parameters Adding feedback To create a dense sounding effect, you can add feedback to each of the taps of the delay. You can also invert the phase of the returning signal as well as filter out low and high frequency elements.
Parameter Edit Mode - 13 D5000 Modulating the delay Add modulation to the delay by changing the parameters accessed by the [MOD] key. Modulation parameters HPF (20 Hz ~ 4.0 kHz or THRU) Set the cutoff frequency for the high pass filter for the feedback loop.
14 - Parameter Edit Mode D5000 Ducking/gating the delay When you set ducking, the delay effect is only applied to the signal when the input level drops below the threshold you set. If you select the gate, the delay effect is applied to the signal when the control level exceeds the threshold.
Parameter Edit Mode - 15 D5000 of a DUCK ) for a very short time. This can sound unnatural, especially if the GATE closes abruptly. There are two parameters which you can adjust, HOLD and RELEASE . By setting a long HOLD time, the gate can be kept open even after the signal has dropped below the threshold.
16 - Parameter Edit Mode D5000 Editing a sampling/playback program To edit a sampling/playback program, press the [ DELAY ] key. FREEZE program The FREEZE program allows you to sample (digitally record) and playback sounds. You can record in stereo for a maximum of 5.
Parameter Edit Mode - 17 D5000 When the D5000 is in standby mode, the bar graph at the bottom of the LCD will have the message " REC. READY " displayed on it. During the recording process, the bar graph indicates the current status. Upon completion of the recording, the message " OK " will be displayed on the bar graph.
18 - Parameter Edit Mode D5000 Page 2: Setting the playback parameters FREEZE PLAY parameters Setting the start and end points for playback Your recorded sample may contain silence or otherwise unneeded sounds at either the beginning or end. Use the START and END parameters to move the playback points to tailor the sample to your needs.
Parameter Edit Mode - 19 D5000 Playback loop You can set a loop point within the sample. This sets the start point for repeats after the first playback. Page 3: Setting the pitch and MIDI note number FREEZE PITCH parameters Press the [ DELAY ] key again to select the third page of the FREEZE program.
20 - Parameter Edit Mode D5000 Page 4: Setting the title and controller assignments This page is identical to Page 3 of the DELAY program (see page 11). S&H (sample and hold) program A sample and hold program allows you to record a sound (sample) and then play it back repeatedly (hold).
Parameter Edit Mode - 21 D5000 The sample and hold function is controlled by the [ TRIGGER ] key or by a footswitch connected to the TRIGGER Footswitch Jack.
22 - Utility Mode D5000 Utility Mode The [ UTILITY ] key allows you to access the system parameters. Each time you press the key, the D5000 cycles to the next command: Until you select one of the other modes, the LED set in the [ UTILITY ] key remains lit.
Utility Mode - 23 D5000 PARAMETER DISPLAY FOOT SW (footswitch) FUNCTION FOOT SW FUNCTION parameters Press the [ UTILITY ] key to select the PARAMETER DISPLAY command. Change the MODE from " NORMAL " to " DETAIL(AUTO) " or " DETAIL(HOLD) " by rotating the DATA ENTRY encoder.
24 - Utility Mode D5000 When the FOOT SW FUNCTION is set to PROGRAM , the D5000 switches to the next program each time you press the footswitch. When the last program in the range ( TO ) is the current program, when you press the footswitch again, it will select the first program again.
Utility Mode - 25 D5000 MIDI CONTROLLER Each D5000 program (except for Sample and Hold programs) can accept input from two MIDI controllers. These parameters allow you to assign a MIDI controller number to the controller channels of the programs (see page 12).
26 - Utility Mode D5000 BULK DUMP procedure The D5000 should be correctly connected to an external MIDI device, for example, a MIDI data filer such as the Yamaha MDF2. Set the desired parameters. Make certain that the external MIDI device is ready to receive your data.
Utility Mode - 27 D5000 REPEAT DELAY This command is only available for the delay programs. It allows you to very rapidly create linear delay programs.
28 - How to initialize the D5000 D5000 How to initialize the D5000 You can reset all programs and system parameters back to their original factory settings with the following procedure: • While pressing the [ < ] " STORE " CURSOR key, turn the power on.
Specifications - 29 D5000 Specifications Audio quality ("WET" circuit) Frequency Response 20 Hz to 20 kHz +/-1.0 dB Dynamic Range greater than 100 dB Hum and Noise less than -76 dB Distortion less than 0.
30 - Preset Program Library D5000 Preset Program Library * As shipped from the factory, the program numbers from 56 to 96 contain the same programs as from 1 to 41. Program number Title Type Input Mode Explanation 1 T120 Single 15 DUAL delay STEREO Simple delay program with single active tap.
100 - Block diagram/Schéma de principe/Blockdeagramm D5000 Block diagram/Schéma de principe/Blockdeagramm Single Stereo D / A D / A A / D LEVEL METER Lch MIX BALANCE OUTPUT L OUTPUT R KEY LCD LED BY.
Dimensions/Abmessungen - 101 D5000 Dimensions/Abmessungen 50 28.5 230.5 21 6.4 D:336.4 3.6 305.4 440 348 H:45.2 1.2 44 W:480.
102 - MIDI Data format D5000 MIDI Data format 1. Transmission Conditions 2. Transmission Data 1) System Exclusive Messages 1 Program Bulk Data When a MIDI BULK DUMP operation is performed with the "PROGRAM" ITEM selected or when a Program Bulk Data Request message is received, the data is transmitted on the currently set MIDI channel.
MIDI Data format - 103 D5000 Checksum 0eeeeeee EOX 11110111 ( F7H ) 3 System Set-up Bulk Data When a MIDI BULK DUMP operation is performed with the "SYSTEM" ITEM selected or when a System Set-up Bulk Data Request message is received, the data is transmitted on the currently set MIDI channel.
104 - MIDI Data format D5000 3. Reception Data and Conditions 4. Reception Data 1) Channel Voice Messages 1 Note Off Received on the currently set MIDI channel (if set to OMNI, all channels received). When a delay program is active or a FREEZE program is set to record, the incoming data can be used as a trigger signal.
MIDI Data format - 105 D5000 00110110 ( 36H ) ASCII “6” 00110011 ( 33H ) ASCII “3” Data Name 01001101 ( 4DH ) ASCII “M” Program 0ppppppp p = 1 (program 1) ~ 100 (program 00) EOX 11110111 ( F7H ) 2 Program Change Bank Bulk Data Request Received on the currently set MIDI channel.
106 - MIDI Data format D5000 Header 01001100 ( 4CH ) ASCII "L” 01001101 ( 4DH ) ASCII "M” 00100000 ( 20H ) ASCII " ” 00100000 ( 20H ) ASCII " ” 00111000 ( 38H ) ASCII ".
D5000 Parameter List - 107 D5000 D5000 Parameter List PR OGRAM No. D A TE: . . TITLE: PROGRAMMER: INPUT MODE: STEREO . L-MONO TYPE: DUAL . SINGLE DISPLAY UNIT: SECOND. DISTANCE. TEMPO. 30FRAME. 25FRAME. 24FRAME TEMPO: DELA Y FB MOD NO TE TIME LEVEL P AN A 1 OFF .
MIDI Implementation YAMAHA [PROFESSIONAL DIGITAL DELAY] Date:07-JUL-1994 Model D5000 MIDI Implementation Chart Version : 1.0 +-----------------------------------------------------------------------+ | | Transmitted | Recognized | Remarks | | Function .
VS10980 R1 1 CR 94 11 500 CR Printed in Japan P.O.Box 1,Hamamatsu,Japan.
デバイスYamaha D5000の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yamaha D5000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha D5000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha D5000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha D5000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha D5000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha D5000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha D5000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha D5000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。