ページ先へ移動 of 94
F200 LF200 F225 LF225 OWNER’S MANUAL LIT -18626-07-15 69J-28199-17 U.S.A.Edition.
ZMU01690 Read this owner’s manual carefully be fore operating your outboa rd motor. U69J17E0.book Page 1 Tuesday, March 7, 2006 10:00 AM.
Important manual information EMU31280 To the owner Thank you for choosing a Yamaha outboard motor. This O wner’s Manual contains infor- mation needed for proper operation, mainte- nance and care. A thorough understanding of these simple instructions w ill help you obtain maximum enjo yment from your new Yamaha.
Table of contents General informa tion .................. ........ 1 Identific ation num bers reco rd .......... 1 Outboa rd motor seria l number ........... 1 Key num ber .................... ........... ......... 1 Emiss ion control informa tion ...
Table of contents Filling fuel ........ ................... ........... 38 Ring Free Fuel Additi ve ............. ....... 38 Operating engine .......... ............ ..... 38 Feeding fuel.............. ............ ............ 38 Starting e ngine ...
Table of contents Consumer information .................... 79 Importan t warrant y inform ation for U.S.A. an d Canada .... ........... 79 YAMAHA MOTOR CORPORATION, U.S.A. FOUR-STROKE OUTBOARD MOTOR THREE-YEAR LIMITED WA RRANTY ............... 81 IMPORTANT WARRANTY INFORMATION IF Y OU USE YOUR YAM AHA OUTSI DE THE USA OR CANADA .
General information 1 EMU25170 Identification numbers record EMU25183 Outboard motor serial number The outboard motor serial n umber is stamped on the label attached to the port side of the clamp bracket.
General informati on 2 EMU25262 Manufactured date label This label is a ttached to the clamp bracket or the swivel bracket. EMU25272 Star la bels Your outboard motor is labeled with a Califor- nia Air Resources Board (CARB) star label. See below for a description of you r particular label.
General information 3 EMU25300 Three Stars — Ultra Low Emission The three-star label identifies engines that meet the Air Resource s Board ’ s 2008 ex- haust emission standards. Engines meeting these standards have 65% lower emissions than One Star-Low-Emission engines.
General informati on 4 ● Know the marine laws and regulations where you will b e boating — and obey them. For basic boating rules, see “ Rules of the road ” on page 5. ● Stay informed about the weather. Check weather forecasts before bo ating.
General information 5 EMU25413 Label (counter rotation models) W ARNING EWM01281 Use only a counterclockwise rotation pro- peller with this engine. Counterclockwise propellers are marked with a letter “ L ” after the size indication.
General informati on 6 Crossing: (you are t raveling across the other vessel ’ s path) Overtaking: (you are passing or being passed by another vess el) In the following illustration, your boat is in the center. You shoul d give the right-of-way to any vessels shown in white area (you are the Give-Way vesse l).
General information 7 vessels, the op erator should sou nd a pro- longed blast on the whistle (4 to 6 seconds). I f another vessel is around the bend, it too should sound the w histle. Even if no reply is heard, however, the vessel s hould still pro- ceed around the bend with caution.
General informati on 8 EMU25540 Fueling instructions W ARNING EWM00010 GASOLINE AN D ITS VAPORS ARE HI GH- LY FLAMMABLE AN D EXPLOSIVE! ● Do not smoke when refueling, and keep away from sparks, flames , or other sources of ignition. ● Stop engine before refueling.
General information 9 ● Take care not to spill gasoline. If gas o- line spills, wipe it up immediately with dry rags. ● Do not overfill the fuel tank.
General informati on 10 EMU25700 Battery requireme nt CAUTION: ECM01060 Do not use a battery that does not meet the specified capacity. If a batter y which does not meet specifications is used, the elec- tric system could perform poorly or be overloaded, causing electric system dam- age.
General information 11 For instructions on propeller removal and in - stallation, see page 64. EMU25770 Start-in-gear protection Yamaha outboard motors or Yamaha -ap- proved remote control units are equipped with start-in-gear protection device(s). This feature permits the engine to be started only w hen it is in neutral .
Basic components 12 EMU25799 Main components NOTE: * May not be ex actly as shown; also may not be included as stand ard equipment on all models . 1. T op cowling 2. Anti -cavitation pl ate 3. T r im tab (anode) 4. Propeller* 5. Cooling water inle t 6.
Basic components 13 EMU26180 Remote control The remote control lever actuate s both the shifter and the throttle. The electrica l switches are mounted on the remote control box. 1 4 6 3 2 5 ZMU05429 1. T achom eter unit (Square type)* 2. T achom eter unit (Round type)* 3.
Basic components 14 EMU26190 Remote control lever Moving the lev er forward from the neutral po- sition engages forward gear. Pulling the leve r back from neutral engages reverse. The en- gine will c ontinue to run at idle until the lever is moved about 3 5 ° (a detent c an be felt).
Basic components 15 NOTE: The neutral throttle lever will operate only when the rem ote control lever is i n neutral. The remote control lever will operate only when the neutral throttle le ver is in the closed position.
Basic components 16 When constant speed is desired, tighten the adjuster to maintain the de sired throttle set- ting. EMU25990 Engine stop lanyard switch The lock plate must be attached to the engine stop switch for the engine to run. The lanyard should be attache d to a secure pl ace on the operator ’ s clothing, or arm or leg.
Basic components 17 With the main switch i n the “” (start) po- sition, the starter motor turns to start the en- gine. When the ke y is released, it returns automatically to the “” (on) position.
Basic components 18 NOTE: For instructions on using the power trim and tilt switch, see page 45. EMU26161 Power trim and tilt s witches (twin bin- nacle type) The power trim and tilt system adjusts the out- board motor angle in relation to the transom.
Basic components 19 EMU26340 Tilt support lever for power trim and tilt or hydro tilt model To keep the outbo ard motor in the tilted up po- sition, lock the tilt support leve r to the clamp bracket. EMU26382 Top cowling loc k lever (pull up type) To remove the engine top cowling, pull up the lock lever(s) a nd lift off the cowling.
Basic components 20 EMU31702 Wate r separ ator This engine has a combina tion fuel filter/water separator and associated w arning system. If water separated from the fuel exceeds a spe- cific volume, the wa rning device will activate. Activation of warning devic e ● The water separator warning i ndicator will blink.
Basic components 21 CAUTION: ECM00020 ● Do not continue to run t he engine if the low oil pressur e warning indicator is on and the engine oil level is lower. Serious engine damage will occur. ● The low oil pressure warning indicator does not indicate the engine oil level.
Basic components 22 NOTE: The speedometer displays km /h, mph, or knots, according to operator preference. Se- lect the desired unit of measurement by set- ting the selector switch on the back of the gauge. See the illustration for settings. EMU26620 Trim met er (di gital t ype) This meter show s the trim angle of your out- board motor.
Basic components 23 EMU26690 Trip meter This gauge displays the distance the boat has traveled since the gauge w as last reset. Press the “” (mode) button re peatedly until the indicato r on the face of the gauge points to “” (trip). To reset the trip meter to zero, press the “” (set) and “” (mode) buttons at the same time.
Basic components 24 EMU26720 Fuel warning indica tor If the fuel level decreases to one s egment, the fuel level warning segm ent will begin to blink. CAUTION: ECM00880 Do not continue to operate the engine with full throttle if a warning device has activat- ed.
Basic components 25 EMU26750 Fuel flow meter The fuel flow meter d isplays the amount of fuel flow over a one hour period, at the current rate of engine operation. If twin engines are installed on your boat, the fuel flow meter display s the total fuel flow of both the port and starboard engin es.
Basic components 26 NOTE: If twin engines are installed on your boat, the gauge will only displ ay the total fuel economy of both engines. NOTE: ● Fuel consumption varies greatly with boat design, weight, propeller used, en gine trim angle, sea conditions (inc luding wind), and throttle position.
Basic components 27 NOTE: If the two engines ’ sp eeds are not synchro - nized while cruising, they can be synchro - nized by adjusting trim angl e or throttle. EMU26791 Water separator warning indicator This indicator wil l blink when water has accu - mulated in the water sepa rator.
Basic components 28 NOTE: The tachometer un it shows various kinds of information accord ing to the setting made us- ing the “” (set) and “” (mode) buttons. For details, see the attached op eration manu- al. Preoperation checks Place the gear shift lever in neutral and turn the main switch to “” (on).
Basic components 29 vice has ac tivated while the appropriate en - gine oil quantity is maintained, consult your Yamaha dealer. CAUTION: ECM01600 Do not continue to run the engine if the low oil pressure w arning device has acti- vated. Serious engine damage will occur.
Basic components 30 CAUTION: ECM00910 Gasoline mixed with w ater could cause damage to the engine. Engine trouble warning This indicator will blink when the engine mal - functions while cruising . Get back to the port soon and cons ult a Yamaha dealer immedi - ately.
Basic components 31 NOTE: After the main switch is first turned on, all the displays come on as a test. After a few sec- onds, the gauge will change to normal opera- tion. NOTE: The speed & fuel meter unit shows various kinds of information accordin g to the setting made with the “” (set) and “” (mode) buttons.
Basic components 32 NOTE: After the main switch is first turned on, all the displays come o n as a test. After a few sec- onds, the gauge will change to normal opera- tion. NOTE: The speedometer unit show s various kinds of information accord ing to the setting made us- ing the “” (set) and “” (mode) buttons.
Basic components 33 EMU26801 Warning system CAUTION: ECM00090 Do not continue to operate the engine if a warning device has activated. Consult your Yamaha dealer if the problem cannot be located and corrected. EMU26824 Overheat warning (twin engines) This engine has an overheat warning device.
Basic components 34 ● The buzzer will soun d. If the warning system ha s activated, stop the engine as s oon as it is safe to do so. Check the oil level and add oil as needed. If the oil level is c orrect and the warnin g device does not switch off, consult yo ur Yamaha dealer.
Operation 35 EMU26901 Installation CAUTION: ECM00110 Incorrect engine height or o bstructions to smooth water flow (such as the design or condition of the boat, or accessories such as transom ladders or depth finder tr ans- ducers) can create airborne water spray while the boat is cr uising.
Operation 36 EMU26930 Mounting height (boat bottom) To run your boat at optimum efficiency, the water resistance (drag) of the boat and out- board motor must be made as little as possi- ble. The mounting height of the outboard motor greatly affec ts the water resistance.
Operation 37 EMU27103 Preoperation checks W ARNING EWM00080 If any item in the preoperation check is not working properly, have it inspected and repaired before operating the outboard motor. Otherwise an accident could occur. CAUTION: ECM00120 Do not start the engine out of water.
Operation 38 NOTE: Be sure to com pletely insert the di pstick into the dipstick guide. EMU30021 Filling fuel W ARNING EWM00060 Gasoline and its vapors are highly flam- mable and explosive. Keep away from sparks, cigarettes, flames, or other sour c- es of ignition.
Operation 39 EMU27490 Starting engine EMU27624 Electric start and remote control models 1. Place the remote control lev er in “” (neutral). NOTE: The start-in-gear protection device prevents the engine from starti ng except when in neu- tral. 2. Attach the engine stop sw itch lanyard to a secure place on your c lothing, or your arm or leg.
Operation 40 3. Turn the main switch to “” (on). NOTE: Dual engine users: When the main switch is turned on, the buzzer operates for a few sec- onds then stops automatically. The buzzer also operates if one of the engines s talls. 4. Turn the main s witch to “” (start), and hold it for a maximum of 5 s econds.
Operation 41 ● A continuous flow of water from the pilot hole shows that the water pump is pumping water through the cooling pas- sages. If water is not flowing out of the pilot hole at all times while the engine is running, overheating and serious dam- age could occur.
Operation 42 To shift from in gear (forward/reverse) to neu- tral 1. Close the throttle so that the engine slows to idle speed. 2. After the engine is at idle sp eed in gear move the remote co ntrol lever firmly and crisply into the neutral positio n.
Operation 43 2. After stopping the engine, disconnect the fuel line or close the fuel cock if th ere is a fuel joint or a fuel cock on the boat. 3. Tighten the air vent screw on the fuel tank cap (if equipped). 4. Remove th e key if the boat will be left un- attended.
Operation 44 complete stop with the engine off. Do not adjust the trim angle with this switch while the boat is moving. Adjust the outboard motor trim angle using the power trim and tilt switch. To raise the bow (trim-out), pres s the switch “” (up).
Operation 45 Bow Down Too much trim-in causes the boat to “ plow ” through the water, decreasing fuel economy and making it hard to increase speed.
Operation 46 2. Disconnect the fue l line from the out- board motor or close the fuel cock . 3. Press the power trim and tilt switch / pow- er tilt switch “” (up) until the outboard motor has tilted up completel y. 4. Push the tilt support knob into the clamp bracket or pull the tilt support lever toward you to support the engine.
Operation 47 CAUTION: ECM00250 Be sure to retract the tri m rods completely during mooring. This protects the rods from marine growth and corr osion which could damage the power trim and tilt mechanism. EMU28055 Procedure for tilting down (power trim and tilt model s / power tilt m odels) 1.
Operation 48 W ARNING EWM00660 ● Place the gear shift in neutral before set- ting up for shallow water cruising. ● Return the outboard motor to its nor mal position as soon as the boat is back in deeper water.
Operation 49 Cruising in turbid water Yamaha strongly recommends that you use the optional chromium -plated water pump kit (not available for s ome models) if y ou use the outboard motor in turbid or muddy water con - ditions.
Maintenance 50 EMU31480 Specificatio ns NOTE: “ (AL) ” stated in the specification data below represents the numerical value for the alumi- num propeller installed. Like wi se, “ (SUS) ” represents the value for stainless steel propeller installed and “ (PL) ” for plastic propeller installed.
Maintenance 51 Gear oil quantity: F200 TR 1150. 0 cm ³ (38 .88 US o z) (40. 56 Imp.oz) F225 TR 1150. 0 cm ³ (38 .88 US o z) (40. 56 Imp.oz) LF20 0TR 1000 .0 cm ³ (33. 81 US oz ) (35.2 7 Imp.oz) LF22 5TR 1000 .0 cm ³ (33. 81 US oz ) (35.2 7 Imp.oz) Tightening torque for engine: Spark p lug : 25.
Maintenance 52 ● Store the outboard motor in a dry, well- ventilated place, not in direct sunlight. EMU28303 Procedure EMU30740 Flushing with the flushing attachment 1. Wash the outboard motor body using fresh water. For further informatio n, see page 55.
Maintenance 53 6. Run the engine at a fast idle for a few minutes in neutra l position while supply- ing fresh water. 7. Just prior to turning off the en gine, quickly spr ay “ Yamaha Stor-Rite Engine Fogging Oil ” (Part No. LUB-STR RT-12-00) alter- nately into the intake s ilencer or the fog- ging hole of the silenc er cover, if equipped.
Maintenance 54 Batteries vary among m anufacturers. There- fore the following procedures may not always apply. Consult your battery manufacturer ’ s in - structions. Procedure 1. Disconnect a nd remove the battery from the boat. Always disconnect the black negative cable first to prevent the risk of shorting.
Maintenance 55 instead of cooling the engine, which can cause serious overheating. Be sure the connector is tightened securely on the fit- ting after flushing the engin e. NOTE: ● When flushing the engine w ith the boat in the water, tilting up the outboard motor until it is completely out of the water will achieve better results.
Maintenance 56 EMU30563 Maintenance chart NOTE: ● Refer to the sections in this chapter for explanations of each owner-specific a ction. ● The maintenance cycle on thes e charts assume usage of 200 hours per year and regular flushing of the cooling w ater passages.
Maintenance 57 EMU28874 Maintenance chart (additi onal) EMU28910 NOTE: When using lead or high-s ulfur gasoline, inspecting v alve clearance may b e required more fre- quently than every 500 hours.
Maintenance 58 EMU28931 Greas ing Yamaha marine grease (Water resistant grease) EMU28952 Cleaning and a djusting spark plug W ARNING EWM00560 When removing or installing a spark plug, be careful not to damage the insulator. A damaged insulator could allow exter nal sparks, which could lead to explosion or fire.
Maintenance 59 The spark plug is an important engine compo- nent and is easy to inspect. The con dition of the spark plug can indicate something about the condition of the engine. For example, if the center electrode p orcelain is very w hite, this could indicate an inta ke air leak or carburetion problem in that cyl inder.
Maintenance 60 Checkpoints ● Fuel system parts leaka ge ● Fuel line joint leakage ● Fuel line cracks or other damage ● Fuel connector leakage EMU29087 Changing engine oil W ARNING EWM00760 ● Avoid draining the engine oil immediate- ly after stopping the engine.
Maintenance 61 3. Remove the oi l filler cap. Add the correct amount of oil through the filler ho le, and install the filler cap. CAUTION: ECM00970 ● Do not overfill the oil, and be sure the outboard motor is upright ( not tilted) when checking and changing the engine oil.
Maintenance 62 9. Dispose of used oil acc ording to local regulations. NOTE: ● For more information on the disposal of used oil, consult your Yamaha dealer. ● Change the oil mo re often when operating the engine under adverse conditions such as extended trolling.
Maintenance 63 EMU29112 Checking wiring and c onnectors ● Check that each ground ing wire is properly secured. ● Check that each connector is engaged se- curely. EMU29120 Exhaust leakage Start the engine and check that no exhaust leaks from the j oints between the e xhaust cover, cylinder head, and body cylinder.
Maintenance 64 5. Check that the tilt rod and trim rods are free of corrosion or other flaws. 6. Activate the tilt-down switch until the trim rods have retracte d completely i nto the cylinders. 7. Activate the trim-up switch until the tilt rod is fully extended.
Maintenance 65 ● Check the propel ler shaft oil seal for dam- age. NOTE: If the shear pin equipped: it is des igned to break if the propeller hits a hard underwater obstacle to help protect the propeller and drive mechanism. The prope ller will then spin freely on the shaft.
Maintenance 66 NOTE: If the propeller nut does not align w ith the pro- peller shaft hole af ter tightening to the speci- fied torque, tighten the nut further to align it with the hole. EMU29282 Changing gear oil W ARNING EWM00800 ● Be sure the outboard motor is se curely fastened to the transom or a stable stand.
Maintenance 67 5. With the outboard motor in a vertical po- sition, and us ing a flexible or pressurized filling device, inject the gear oil into the gear oil drain screw hole. 6. Put a new gasket on the oil level plug. When the oil begins to flow out of the oil level plug hole, insert and tighten the oil level plug.
Maintenance 68 ● Avoid bodily contact with electrolytic fluid as it can cause severe burns or per- manent eye injury. ● Wear protective eye gear when handling or working near batteries. Antidote (EXTE RNAL): ● SKIN - Flush with wat er. ● EYES - Flush with water for 15 minutes and get immediate medical attention.
Maintenance 69 ● Connect the red battery cable first when installing the battery and disconnect the black battery ca ble first when removing it. Otherwise, the electrical parts can be damaged. ● The electrical contacts of the battery and cables must be clean and properly connected, or the battery will not start the engine.
Maintenance 70 EMU29400 Coating the boat bottom A clean hull improves boat performance. The boat bottom should be kept as clean of marine growth as possible. If nece ssary, the boat bot- tom can be c oated with an anti-foulin g paint approved for your area to inhibit marine growth.
Trouble Recovery 71 EMU29424 Troubleshooting A problem in the fuel, compression, or ignition systems can cause poor starting, los s of pow- er, or other problems. This section describes basic checks and possible remedies, and cov - ers all Yamaha outbo ard motors.
Trouble Recovery 72 A. Check for pinched or kinked fuel li ne or oth- er obstructions in fuel system . Q. Is fuel contaminated or stale? A. Fill tank with clean, fresh fuel. Q. Is fuel filter clogged? A. Clean or replace filter. Q. Have ignition parts fail ed? A.
Trouble Recovery 73 Q. Is load on boat improperly dis tributed? A. Distribute load to pl ace boat on an even plane. Q. Is water pump or thermostat faulty? A. Have serviced by a Yamaha dealer. Q. Is there excess water in fuel filter cup? A. Drain filter cup.
Trouble Recovery 74 A. Connect corr ectly. Q. Is heat range of spark plug incorrect? A. Inspect spark plug and replace it with rec- ommended type. Q. Is high press ure fuel pump drive belt br o- ken? A. Have serviced by a Yamaha dealer. Q. Is engine not responding properly to shift lever position? A.
Trouble Recovery 75 EMU29492 Replacing fuse If the fuse has blown on an electric start mod- el, open the fuse box and use a f use puller to replace the fuse with a spare one of the prop- er amperage. W ARNING EWM00630 Be sure to use the specified fuse.
Trouble Recovery 76 NOTE: Consult your Yamaha dealer if the new fuse immediately blow s again. EMU29522 Power tr im and tilt / power tilt w ill not operate If the engine c annot be tilted up or down w.
Trouble Recovery 77 4. Unscrew the filter cu p from the filter hous- ing. NOTE: Be careful not to twist the water detection switch lead when unscrew ing the filter cup. 5. Drain the water in the filter cup by soaking it up with a rag. NOTE: Properly dispose of the rag.
Trouble Recovery 78 EMU29970 Procedure 1. Thoroughly was h away mud, sa lt, sea- weed, and so on, with fresh water. 2. Remove the spark plu gs and face the spark plug holes downward to allow any water, mud, or contaminants to drain. 3. Drain the fuel from the vapor separator, fuel filter, and fuel line.
Consumer information 79 EMU29811 Important warranty information f or U.S.A. and Canada U69J17E0.book Page 79 Tuesday, March 7, 2006 10:00 AM.
Consumer information 80 U69J17E0.book Page 80 Tuesday, March 7, 2006 10:00 AM.
Consumer information 81 EMU29830 YAMAHA MOTOR CORPORATION, U .S.A. FOUR-STROKE OUTBOARD MOTOR THREE-YEAR LIMITED WARRANTY U69J17E0.book Page 81 Tuesday, March 7, 2006 10:00 AM.
Consumer information 82 U69J17E0.book Page 82 Tuesday, March 7, 2006 10:00 AM.
Consumer information 83 EMU29841 IMPORTANT WARRANTY INFORMA TION IF YOU USE YOUR YAMAHA OUTSIDE THE USA OR CANADA U69J17E0.book Page 83 Tuesday, March 7, 2006 10:00 AM.
A5-tate_Blank.fm Page 1 Friday, May 16, 2003 9:00 AM.
A5-tate_Blank.fm Page 1 Friday, May 16, 2003 9:00 AM.
March 2006–1.8 × 1 CR Printed in Japan Printed on recycled paper Y AMAHA MOT OR CORPORA TION, USA.
YAMAHA MOTOR CO., LTD. MADE IN JAPAN PAYS D'ORIGINE JAPON OUTBOARD MOTOR W ARRANTY REGISTRA TION ENREGISTREMENT DE LA GARANTIE DU MO TEUR HORS-BORD Please complete and mail this card. This information is necessary to accurately register your unit for warranty .
PLACE POST AGE HERE A T TN: W ARR ANTY DEP ARTMENT Warranty card 2/27/02 11:47 AM Page 2.
Yamaha F225をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYamaha F225の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yamaha F225の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yamaha F225で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yamaha F225を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYamaha F225の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yamaha F225に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYamaha F225デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。