Yard Machinesメーカー410の使用説明書/サービス説明書
ページ先へ移動 of 20
IMPOR T ANT : READ SAFETY R ULES AND INSTR UCTIONS CAREFULL Y MTD PR ODUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 REAR TINE TILLER Models 410 Thru 420 O PERA T OR’S M ANU AL Warning: T.
2 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE YOUR TILLER.
3 • Only use accessories approved for this machine by the manufacturer. Read, understand, and follow all instructions provided with the approved accessory. • If situations occur which are not covered by this manual, use care and good judgment. Contact your dealer for assistance.
4 SECTION 2: FINDING YOUR MODEL NUMBER This Operator’s Manual is an important part of your new tiller. It will help you assemble, prepare and maintain your tiller.
5 SECTION 5: ASSEMBLY INSTRUCTIONS This instruction manual covers several different model tillers. Follow only those instructions which pertain to your unit. NOTE: Left and right is determined from the operator’s position, standing behind the tiller.
6 Figure 5 4. Place the hex opening of the hex nut retainer bracket over the flange nut securing the handle adjustment lock and install the lock nut on the lower shoulder bolt. See Figure 6. Figure 6 5. Pivot handle assembly into position desired. Tighten the bottom bolt and nut securely.
7 1. Remove the T-handle, nut, hairpin clip, and rubber washer from the ends of the handle adjustment rod. Slide the rod up through the left side of the bracket on the front of the handle assembly. Refer to Figure 7. 2. Slide the rubber washer on the unthreaded end of the handle adjustment rod.
8 SECTION 6: CONTROLS Figure 12 GEAR SELECTION HANDLE The gear selection handle is located on the front of the handle assembly (right hand handle on Model 420). It is used to select NEUTRAL, REVERSE, or one of the FORWARD modes. This tiller is designed for the gear selection handle to be moved while the engine is running.
9 SECTION 7: OPERATION NOTE: Engine is shipped without oil. BEFORE ST ARTING 1. Service engine with oil as instructed in the separate engine manual packed with your unit. 2. Fill fuel tank with clean, fresh, lead-free, low- lead or regular grade leaded gasoline.
10 SECTION 8: HOW TO USE YOUR TILLER WARNING: When operating the tiller for the first time, use the depth stake setting that gives 1 inch of tilling depth (second hole from the top). Refer to Figure 14. Tilling depth is controlled by the depth stake which can be adjusted to five different settings.
11 SECTION 9: ADJUSTMENTS HANDLE ADJUSTMENT The handle height may be adjusted. On Model 420, the handle may also be adjusted to be in line with the tiller, or swung to the left or right.
12 TIRES Recommended operating tire pressure is approximately 14 p.s.i. on 14 inch tires and 20 p.s.i. on 16 inch tires. (Check sidewall of tire for tire manufacturer’s recommended pressure). Maximum tire pressure under any circumstances is 30 p.s.i.
13 SECTION 13: TROUBLE SHOOTING GUIDE Note: For repairs beyond the minor adjustments above, contact your local authorized service dealer. T rouble P ossible Cause(s) Corrective Action Engine f ails to star t Fuel tank empty , or stale fuel. Throttle control le ver not in correct star ting position (if so equipped).
14 Models 410-415.
15 Models 410-415 REF . NO . PA R T NO DESCRIPTION 1 735-0246 Vinyl End Plug 2 647-0014 Clutch Control Ass’y . 3 710-1017 T orx Mach. AB-T ap Scr . 1/4 x .62" Lg. 4 786-0131 Handle Cov er 5 786-0098 Retaining Brkt.—R.H. 6 786-0118 Retaining Brkt.
16 Models 410, 415, 420 REF . NO . P AR T NO . DESCRIPTION 1 710-0118 He x Bolt 5/16-18 x .75" Lg. 2 712-3004A He x T op L-Nut 5/16-18 Thd. 3 786-0107 Cable Mtg. Brack et 4 710-1017 T orx Mach. AB-T ap Scr . 1/4 x .6" Lg 5 738-0899 Belt Cov er Bolt 6 786-0117 Shift Cov er Bracket 7 786-0100 Belt Cov er 8 736-0142 Fl-W ash.
17 Models 410, 415, 420 REF . NO . P ART NO . DESCRIPTION 1 721-0295 Chain Case Gasket 2 786-0086 Reinf orcement Plate 3 716-0865 Snap Ring 4 750-0938 Spacer .735" I.D . x .886" O .D . 5 611-0058 Wheel Shaft 6 717-1458 Spur Gear 46T 8 736-0351 Fl-W ash.
18 Model 420.
19 Model 420 REF . NO . P ART NO . DESCRIPTION 1 735-0246 Vinyl End Plug 2 647-0014 Clutch Control Ass’y . 3 710-1017 T orx Mach. AB-T ap Scr . 4 786-0131 Handle Cov er 5 786-0098 Retaining Brkt.—R.H. 6 786-0118 Retaining Brkt.—L.H. 7 720-0278 Grip (2 Req’ d.
MANUF A CTURER’S LIMITED W ARRANTY FOR: For TWO YEARS from the date of retail purchase within the United States of America, its possessions and territories, MTD PRODUCTS INC will, at its option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.
デバイスYard Machines 410の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Yard Machines 410をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYard Machines 410の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yard Machines 410の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yard Machines 410で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yard Machines 410を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYard Machines 410の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yard Machines 410に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYard Machines 410デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。