Yard Machinesメーカー580 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 28
IMPORT ANT : READ SAFETY RULES AND INSTRUCTIONS CAREFULL Y MTD PRO DUCTS INC. P .O . BO X 368022 CLEVELAND , OHIO 44136-9722 22” Side Dischar ge High Wheel La wn Mo wer Model Series 580 PRINTED IN U .
2 SECTION 1: FIND ING LAWN M OWER MODEL NUMBER This Operator’s Manual is an important part of y our new lawn mowe r . It will help you assemble, prep are and maintain you r mowe r prope rly.
3 SECTION 3: IMPORTANT SAFE OPERATION PRACTICES WARNING : Thi s symbol p oints out impor tant safet y instr uctions which, if not fol lowed, could endanger the person al safe ty and/or pr operty o f yoursel f and othe rs. Read and follow all in stru ctions in this manual bef ore at tempting to operate y our lawn mower.
4 serious personal i njury. Keep a firm hold on the handle a nd walk, nev er run. If you feel you a re losing your footin g, RELEASE THE BLADE CONTROL HANDLE IMMEDIATELY and the blade will stop rotating within three seconds. • Mow only in daylight or good artifici al light.
5 stopp ed. Disconnect the spark plug wire, and keep the wire a way from the spark plug to prevent acciden tal starting. • Check the bla de and engine m ounting bolts at frequent in tervals for prop er tightness. Als o, visuall y inspect blad e for damage (e .
6 SECTION 4: SLOPE GAUGE 15° SIGHT AND HOLD THIS LEVEL WITH A VERTI CAL TR EE A POWER POLE A CORNER OF A BUI LDING OR A FENCE POS T F O L D O N D O T T E D L I N E , R E P R E S E N T I N G A 1 5 ° S L O P E USE THIS PAGE A S A GU IDE TO DETER MIN E SLOP ES WHERE YOU MAY N O T OPE RAT E SAF ELY.
7 SECTION 5: CON TENTS OF HARDW ARE PACK For identificat ion pur poses, lay out the har dware accordi ng to the i llustration below . P ar t numbe rs are shown in parenth eses. (Har dware pack may contain extra items whic h are no t used on your unit.
8 SECTION 6: UNPACKING Remo ving Unit from Carton • Remo ve staples , break gl ue on top flaps, or c ut tape at car ton end an d peel along top flap to op en carton . Remove lo ose p arts if i ncluded with un it (i.e., o perator 's manu al, etc.
9 Assembling Handle Figure 5 • Raise t he lowe r handle in the directi on sho wn in Fi gure 5 (ste p 1) t ill it snap s into place. • Raise t he uppe r hand le in the direct ion sho wn in Fi gure 5 ( step 2). Tighten the hand knobs wh ich are already on the han dle.
10 • Attach the othe r end of th e struts as foll ows. Plac e one cup ped was her ove r each hex bolt alig ning t he crowned side of the wa sher aga inst t he head of th e bolt . Insert h ex bol ts up thr ough th e middle holes in deck besi de the e ngine and then thr ough the s truts.
11 • Inst all the oth er whe el asse mbly and the othe r end of th e axle s haft in the sa me way. • Remo ve the blo cks fr om the rea r of th e mower a nd place the rear height adjusters in the same relative position as the two front height adj usters.
12 • Push th e hooks on top o f the ba ffle til l these s nap over the hing e on the discha rge chute . Relea se the chute deflec tor . Figure 11 SECTI ON 8: CON TROLS IMPORTANT: Always wear safe ty glasses while ope rating the mower, or while per forming a ny adjustmen ts or repairs o n it.
13 Drive Clutch Control Squeez e the dri ve clutc h con trol aga inst th e upper h andle of the mo wer to eng age the drive m echan ism and move the wh eels. Release t he driv e clutch control to slow do wn the m ower when negotia ting a n obsta cle, making a turn, or stopping the mowe r.
14 Before Star ting • Attach s park plug wire t o spark pl ug. If y our unit is equip ped with a rub ber boot o ver the end of th e spark plug wir e, make c ertain t he meta l cap on t he end o f the spar k plug wi re (insi de the rubber boot) is fastened secu rely ov er th e metal tip on the spar k plug.
15 • Squeez e the d rive clutc h co ntrol aga inst t he uppe r handle of the m ower to eng age the drive m echan ism and move the whee ls. Re lease the drive c lutch contr ol to sl ow down the mowe r when neg otiating a n obstacle, m aking a tu rn, or s topping th e mower.
16 • Turn the lower handl e around s o the notc h on th e bottom of the lowe r hand le is fa cing f orward a s shown in Figu re 14B. R easse mble, placing the botto m hole s in the h andle over the weld pi ns in the handl e mounting b racket . • Reasse mble t he uppe r handle to the l ower hand le.
17 • To adj ust the dr ive clutc h, rotate the adj ustment wh eel wit h your fi ngers. You sh ould rot ate the w heel clockw ise to tighte n the cabl e and cou nter-cl ockwis e to lo osen the c able.
18 Figure 17 SECTION 12: M AINTENANCE WARNING: Alway s stop eng ine an d discon nect s park plug w ire be fore p erfo rmi ng any m ain ten anc e work or ad justmen ts on your lawn mowe r.
19 To Remove B lade • Remo ve the bolt and th e bell washer sec uring th e blad e assemb ly to the cran kshaft. S ee Figur e 18A. • Remo ve the two p airs of hex bo lt and loc k nut holding t he blad e to the bl ade ada pter and th e pull ey assembl y.
20 Replacing Rear Flap The rea r fla p is attach ed to t he back of the mower deck, an d is des igned to mi nimize t he poss ibility of obj ects being th rown from the rear of the mower towards the ope rator . If the rear fla p is dam aged, repl ace as follows.
21 • Lift and s tabiliz e the fron t of the d eck. • Loosen th e cent er hex bo lt and lower the blade and eng ine pul ley until there i s ade quate cle arance t o move the belt past th e belt kee per. • Remove th e belt f rom the en gine p ulley an d arou nd the bla de.
22 SECTI O N 14: TROUBLE SHOOTING GUIDE Note: For repair s beyon d the mino r adj ustmen ts liste d abov e, con tact your local authoriz ed se rvice dealer. T r ouble P ossible Cause(s) Corrective Actions Engine f ails to start Blade control handle disenga ged.
23 SEE ENGI NE MANU AL 31 1 2 3 4 6 7 8 12 15 17 68 13 9 11 10 14 16 20 21 19 18 22 23 24 25 26 28 27 67 66 54 29 30 55 56 61 62 63 64 65 60 59 57 53 52 51 50 44 45 47 48 46 49 41 36 34 36 43 42 33 37.
24 Ref. No. P ar t No. Descrip tion 1 731-1057 Upper Driv e Cov er 2 731-0620 Drive Lev er 3 731-1058 Low er Driv e Cov er 4 731-1059 Mounting Cap 5 710-1667 Screw # 10-16 x .625 6 746-0960 Drive Cable 7 747-0824 Control Le v e r 647-0004 Delux e 8 749-0539C Upper Hand le 9 746-0875 Throttle H ousing † 10 736-0501 Curved W ash er .
25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 21 50 33 30 31 32 35 36 38 39 40 43 46 47 51 45 44 51 43 46 47 53 52 42 41 37 40 39 33 34 32 31 30 36 20 19 22 23 24 25 26 27 28 19 20 49 48 29 52 53 54.
26 Hardw are: 710-1256 (Scre w) Pa r t N o. 751B281 439 751B281 440 751B281 443 Color Dark Red Blac k Bright Red Hardw are: 710-1256 (Scre w) Pa r t N o.
27.
MANUF A CTURER ’ S LIMITED W ARRANTY FOR: For TWO Y EARS from the date of re tail purcha se within th e United Stat es of Am erica, i ts poss essio ns and territorie s, MTD PRODUCTS IN C will, at it.
デバイスYard Machines 580 Seriesの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Yard Machines 580 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはYard Machines 580 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Yard Machines 580 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Yard Machines 580 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Yard Machines 580 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はYard Machines 580 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Yard Machines 580 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちYard Machines 580 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
