Z-ComメーカーXG-762Nの使用説明書/サービス説明書
ページ先へ移動 of 17
1 The User Guide of XG - 762N USB Linux Driver.
2 1. Introduction Because more and more people install the Linux operating system in the desktop and notebook, we provide the Linux solution of our XG - 762N 802.11 a+ b+g Wireless LAN Card. XG - 762N provides 802.11 a+ b+g wireless solution for USB interface.
3 2. Building the device driver In this section, we will describe how to bu ild our XG - 762N Linux driver under the Linux operating system. 2.1 Package Extraction The first thing one should do is to uncompress this package by tar. After untar ing this package, you can see the source files .
4 to install the driver. 2. 4 Build the debugging tool There are two debugging tools in this package, ¡° apdbg ¡± and ¡° menudbg ¡± . Run ¡° make debug ¡± to compile them both. If you don ¡¯ t have the ncurse library, you may get s ome error messages while compiling menudbg .
5 3. Getting Start 3.1 Load the driver Generally, the driver is automatically loaded when the XG - 762N dongle inserts. If not, o ne can use the modprobe ¨C v XG -762N to load our driver. In order to check whether our driver is loaded successfully, one can use the ¡° lsmod ¡± f or t hi s check.
6 Example: iwconfig ethX channel <channel> The channel can vary from 1 to 14. One should note that, the set channel command will NOT work under the Managed (infr astructure mode). Because in the in this mode, the channel should change to channel of the AP we want to associate.
7 Except for commands support for wireless extension, we also define some commands for us to set parameters to our driver. One can u se the ¡°i wpri v¡± for this purpose.
8 The Cell Number is got from the site survey operation by the doing ¡°i wli st ¡± command. We recommend that user uses the following scenario under the Managed ( Infrastructure) or Adhoc mode. One can first do the site survey command by the following command: Then, associate with the AP with the Cell number got from the iwlist command.
9 O r inactivate it. Or get its current state 3.5 Set up IP address If you use the RedHat distribution Linux, you can edit the /etc/sysconfig/network - scripts/ifcfg - ethX or edit the /etc/network/interfaces under the Debian to set up th e IP address on booting process.
10 3. 6 Wo rking with Linux WPA supplicant Note: I do the following procedure in Fedora Core2, for other distribution package, you may need install additional libraries (ex. openssl) required to build the wpa supplicant.. 3. 6 .1 Setup the Linux wpa supplicant - Copy wpa_supplicant.
11 description , you can refer to the original sample configuration file: wpa_supplicant.conf) wpa_supplicant_psk.conf to meet wpa - psk test condition. Sample settings for wpa - psk: Similarily, for wpa eap - tls and wpa peap, its sample setting block: For WPA EAP - TLS Note1: The fluffy.
12 Note2: You can run openssl utility (Included in openssl.zip) in Microsoft Windows OS. Note3: The detailed description, please refer to CertConvReadme.txt. (Located in lnx_wpa_supplicant.tar.gz) For WPA PEAP - After modifying, use the following command to setup WPA connection.
13 note: @- i: interface name: eth1 @- c: Configuration file: wpa_supplicant_psk.conf @- D: The name of network interface. You will see the following message if wpa -p sk connection is built successfully. ... WPA: Sending EAPOL - Key 2/2 --- > The Group handshake is about to finish.
14 address of Station different. The command to specify association address is very simple : You must set the first byte = 01 to indicate this is for assoc iation address assignment only. The remainder XXXXXXXXXX is byte1 - byte5 of PC ¡¯ s MAC address.
15 4 . Turbo Mode This chapter describes h ow to enhance the performance by enabling the ZyDAS turbo mode. Turbo mode is a composition of Burst Mode and Large Packet Mode . You may known that the so - call ¡° Turbo M ode ¡± always has compatibility problems .
16 the last frame from that station is a large packet. Therefore, AP can accept station capable of large packet or not. In Station mode, You need to re - associate with the AP to update your Turbo Mode status . Y o u need to remind something in mind. Large packet needs to merge two frames into one.
17 5 . Conclusion This document doesn¡¯t expl ai n ho w t o set up t he wir el ess LAN environment in detail. One may get some probl ems when setting up the wireless LAN environment. If you have any question about how to set up the environment, you can send an e- mail to us or find the solution on the network.
デバイスZ-Com XG-762Nの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Z-Com XG-762Nをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZ-Com XG-762Nの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Z-Com XG-762Nの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Z-Com XG-762Nで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Z-Com XG-762Nを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZ-Com XG-762Nの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Z-Com XG-762Nに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZ-Com XG-762Nデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
