ZanussiメーカーZGF 782の使用説明書/サービス説明書
ページ先へ移動 of 19
2 GAS HOB MODEL ZGF 782 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance.
3 Important Safety Infor mation You MUST read hese warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 01635 521313 Installation ● This hob must be installed by qualified personnel, according to the manufacturer ’ s instructions and to the relevant British Standards.
4 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low V oltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive) ; * 90/396 .
5 1. Hob Top 2. Auxiliary Burner 3. Semi-rapid Burners 4. Ultra-rapid Double-crown Burner 5. Rapid Burner 6. Ignition pushbutton 7. Control knob for front left burner (auxiliary) 8. Control knob for back left buner (semi-rapid) 9. Control knob for central burner (ultra-rapid) 10.
6 Operation HOB BURNERS To light a burner, push the relevant control knob in, turn it anticlockwise to maximum position, and depress the ignition pushbutton marked by a small electric spark symbol. Then adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again.
7 Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply . The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool.
8 Something Not W orking? If the hob is not working correctly , please carry out the following checks before contacting your local Zanussi Service Force Centre.
9 ZANUSSI GUARANTEE CONDITIONS W e, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of.
10 OVERALL DIMENSIONS W idth: 680 mm. Depth: 510 mm. Height: 72 mm. W eight: 12 Kg. CUT OUT DIMENSIONS W idth: 560 mm. Depth: 480 mm. Thickness: 30 mm. Ignition HT Spark Spark Generator Ispra Control's BF 50066 - 240V 0.6 Y A T 120 Spark Gap Fixed Rear Left Burner (semi rapid) Heat Input 2.
11 INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITHOUT A COOKER HOOD ABOVE INSTALLATION GUIDANCE INSTRUCTIONS CLEARANCES REQUIRED WHEN FITTING THE GAS HOB WITH A COOKER HOOD ABOVE 700 mm 400 mm 100 mm 400 mm 50 mm 50 mm 55 mm 650 mm 400 mm 400 mm 100 mm 50 mm 50 mm 55 mm 600 mm 780 mm min.
12 Rectangular cut-out size for hob A) End of shaft with nut B) W asher C) Elbow It is important to install the elbow correctly , with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas.
13 ON/OFF SWITCH FLEX OUTLET ON/OFF SWITCH FLEX OUTLET FO 0763 FO 0764 30 20 min 60 a b FO 1013 1 2 3 50 50 FO 2039 FO 0199 a Fitting the Hob into the w orktop Carry out the building in of the hob as follows: • put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm.
14 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed.
15 A. IGNITOR SWITCH B. IGNITOR UNIT B L N 0 1 2 3 4 5 6 220/240 A W iring Diagram.
16 Fault Finding Pr eliminar y Electrical Systems Check A. EAR TH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary . a) T est leads from any appliance earth point to earth pin on plug.
17 Ignition System / Gas Ignition YES Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity of appliance Ignitor does not spark Check .
18 Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. T o do this, follow the procedure below . - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times.
19 A: Removal Of Hob Top 1. Remove all control knobs, pan supports, burner caps and burner crowns. 2. Remove 2 screws for each burner . 3. Remove 6 fixing screws from the pan support hinges, and remove the hinges from the hob. 4. Lift hob top at the rear and disengage it from the front locators.
20.
デバイスZanussi ZGF 782の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zanussi ZGF 782をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZanussi ZGF 782の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zanussi ZGF 782の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zanussi ZGF 782で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zanussi ZGF 782を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZanussi ZGF 782の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zanussi ZGF 782に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZanussi ZGF 782デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。