ZanussiメーカーZU 9100 Fの使用説明書/サービス説明書
ページ先へ移動 of 20
FREEZER ZU 9100 F 2222740-41 INSTRUCTION BOOKLET.
2 Instructions for the User Important Safety Instructions 3 Description of the Appliance 4 Operation 4 Before use 4 Freezer controls 4 Starting your appliance 5 T emperature control 5 W arning light (.
IMPORT ANT SAFETY INSTRUCTIONS These warnings are provided in the interests of your safety . Ensure that you understand them all before installing or using this appliance. Y our safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Departement.
1 2 3 4 5 6 DESCRIPTION OF THE APPLIANCE 4 OPERA TION Freezer controls Before use Remove all securing tapes. W ash inside the appliance with lukewarm water and bicarbonate of soda (5 ml to 0.5 litre of water). Do not use soap or deter- gent as the smell may linger .
Starting your appliance Insert the plug into the wall socket. The appliance can be activated/deactivated by pressing the ON/OFF button.When the pilot light ➂ is illuminated this shows that the appliance is on. T emperature control The temperature within the freezer is controlled by the thermostat ➀ situated at the bottom of the cabi- net .
Internal thermometer This indicates the internal temperature of the freez- er . It may indicate a temperature above -18°C when large quantities of food are placed inside for freezing or when the door is left open for a long time.
The freezer compartment will become progressively covered with frost. This should be removed with the special plastic scraper provided, whenever the thick- ness of the frost exceeds 1/4". During this operation it is not necessary to switch off the power supply or to remove the foodstuffs.
Before any maintenance or cleaning work is carried out, DISCONNECT the appliance from the ELEC- TRICITY supply . W arning This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorised technicians.
9 If after the above checks, there is still a fault, call your local Service Force Centre. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.
10 SER VICE AND SP ARE P ARTS In the event of your appliance requiring service, or if you wish to purchase spare parts please contact your local Zanussi Service Force Centre by telephoning: 0870 5 929929 Y our call will be automatically routed to the Service Force Centre covering your post code area.
11 Standard guarantee conditions We, Zanussi, undertake that if within 24 months of the date of purchase this Zanussi appliance or any part there- of is proved to be defective by reason only of faulty.
DIMENSIONS Height 81,5 cm Width 59,6 cm Depth 53,8 cm POWER SUPPL Y VOL T AGE AND FREQUENCY 220-240 V / 50 Hz TOT AL POWER ABSORBED 90 W A VERAGE DAIL Y UNITS ELECTRICITY (*) 0,75 kWh GROSS CAP ACITY 108 l NET CAP ACITY 100 l ST AR RA TING (*) This figure is based on standard test results in accordance with European Standard EN153.
ELECTRICAL CONNECTION W ARNING: THIS APPLIANCE MUST BE EARTHED. The manufacturer declines any liability should this safety measure not be observed. If the plug that is fitted to your appliance is not suit- able for your socket outlet, it must be cut off and the appropriate plug fitted.
14 BUILDING-IN INSTRUCTIONS Before carrying out any work, remove the plug from the power socket. Door Reversal Left door opening: 1. Remove the grid from the appliance pulling it towards you with hands. 2. Remove the left side (A) of the grid cutting it from the rear (see figure).
15 T o reverse the opening direction of the door , proceed as shown in the figures: Attention After completion of the door reversing opera- tion, check that the door gasket adheres to the cabinet. If the ambient temperature is cold (i.e. in Winter), the gasket may not fit perfectly to the cabinet.
16 Building the appliance in under a worktop The dimensions of the recessed installation area must correspond with those indicated in the figure. Remove covering and adjusting strips.
17 T o mount the furniture door proceed as shown in the figures:.
Screw appliance into place. Refit the covering strip. 18.
Fitting the plinth Important For the efficient operation of the appliance, it is important that the original ventilation grid is used. ■ For an opening height dimension A=820 mm and a plinth height dimension a=100 mm, the plinth may be fitted without adjustments.
© Electrolux Household Appliances Limited 2000.
デバイスZanussi ZU 9100 Fの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Zanussi ZU 9100 Fをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZanussi ZU 9100 Fの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zanussi ZU 9100 Fの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zanussi ZU 9100 Fで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zanussi ZU 9100 Fを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZanussi ZU 9100 Fの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zanussi ZU 9100 Fに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZanussi ZU 9100 Fデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
