ZanussiメーカーZWN 6120 Lの使用説明書/サービス説明書
ページ先へ移動 of 24
EN User manual Washing Machine ZWN 6120 L.
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 First use _ _ _ _ _ _ .
• If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance. • Always be sure, that there is no water leakage from ho- ses and their connections after the installation.
Product description 1 Detergent dispenser drawer 2 Control panel 3 Door opening handle 4 Rating plate 5 Drain pump 6 Adju stable feet 1 2 3 4 5 6 Detergent dispenser drawer Compartment for detergent used for prewash and soak phase or for stain remover used during the stain action phase (if available).
Control panel Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and pilot lights. These are presented by relevant numbers on the following pages.
Indicator pilot light (7) When selecting a washing programme both lights 7.1 and 7.2 illuminate. After having pressed the button 5 the only light corre- sponding to the running phase stays on. The machine starts working and the door is locked. The light 7.
Flap for powder or liquid detergent UP- The flap position if using POWDER detergent DOWN - The flap position if using LIQUID detergent during main wash If the flap is not in the desired position: MAX • Pull out the dispenser drawer until it stops. The flap is down and you wish to use powder detergent: • Turn the flap up.
The selector dial can be turned either clockwise or coun- terclockwise. Turn to position to reset programme/ Switching the machine off. At the end of the programme the selector dial must be turned to position , to switch the machine off.
If you cannot open the door but you need to open it you have to switch the machine off by turning the selector dial to . After a few minutes the door can be opened (pay attention to the water level and temperature!) . After closing the door, it is necessary to select the pro- gramme and options again and to press button 5 .
Ink: depending on the type of ink, moisten the fabric first with acetone 1) , then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thor- oughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment COTTONS ECO 60° and 40° Main wash - Rinses Maximum spin speed at 1200 rpm Max. load 8 kg This programme can be selected for normally soiled cotton items.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment WOOL 40° Main wash - Rinses Maximum spin speed at 900 rpm Max. load 2 kg Washing programme for machine washable wool as well as for hand washable woollens.
Programme - Maximum and Minimum Temperature - Cycle De- scription - Maximum Spin Speed - Maximum Fabrics Load - Type of Laundry Options Detergent Com- partment SPIN Drain and long spin Maximum spin speed at 1200 rpm Max. load 8 kg Separate spin for hand washed garments and after programmes with the Rinse Hold option selected.
Cleaning the pump The pump should be inspected regularly and particularly if: • the appliance does not empty and/or spin; • the appliance makes an unusual noise during draining due to objects such as safety pins, coins etc. blocking the pump; • a problem with water draining is detected (see chapter “What to do if.
Cleaning the water inlet filt ers Important! If the appliance doesn't fill, takes long to fill with water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked .
What to do if… Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
Problem Possible cause/Solution There is water on the floor: Too much detergent or unsuitable detergent (cre ates too much foam) has been used. • Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings.
Problem Possible cause/Solution Spinning starts late or the machine does not spin: The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rota- tion of the drum.
Consumption values Programme Energy consumption (kWh) 1) Water consumption (litre) 1) Programme duration (minutes) 1) White Cottons 90 °C 2.1 65 145 Cottons 60 °C 1.4 63 120 Cottons 40 °C 0.6 63 140 Synthetics 40 °C 0.45 37 85 Delic ates 40 °C 0.
Unscrew the three bolts. Slide out the relevant plas- tic spacers. Open the porthole and re- move the polystyrene block fitted on the door seal. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet.
The other end of the inlet hose which connects to the appliance can be turned as showe d in the picture. Do not place the inlet hose downwards. Angle the hose to the left or right depending on the position of your water tap. Set the hose correctly by loosening the ring nut.
If the outlet spigot has not been used before, remove any blanking plug that may be in place. Push the drain hose onto the spigot and secure with a clip, ensure a loop is formed in the drain hose (see above) to prevent waste from th e sink enter- ing the appliance.
your local council, your household waste disposal service or the shop where you purchas ed the product. Packaging materials The materials marked with the symbol are recyclable.
www.zanussi.com/shop 192985530-A-312011.
デバイスZanussi ZWN 6120 Lの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zanussi ZWN 6120 Lをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZanussi ZWN 6120 Lの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zanussi ZWN 6120 Lの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zanussi ZWN 6120 Lで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zanussi ZWN 6120 Lを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZanussi ZWN 6120 Lの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zanussi ZWN 6120 Lに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZanussi ZWN 6120 Lデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。