ZanussiメーカーZWS 281の使用説明書/サービス説明書
ページ先へ移動 of 20
EN User manual Washing Machine ZWS 281.
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Environment concerns _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Technical information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Product description _ _.
Water connection • Do not connect the appliance with old hoses already used. Only use new hoses. • Make sure not to cause damage to the water hoses. • Do not connect the appliance to new pipes or pipes not used for a long time. Let the water flow for some mi- nutes, then connect the inlet hose.
Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 10 bar (1 MPa) Water supply 1) Cold water Maximum load Cotto n 5 kg Spin speed Maximum 800 rpm 1) Connect the water inlet hose to a water tap with a 3/4' ' thread.
Control panel 1 3 4 5 2 6 7 8 9 1 Programme knob 2 Start button 3 Programme phase indicator 4 Easy iron button 5 Extra rinse button 6 Rinse hold button 7 Prewash button 8 Spin button 9 Delay Star button Programme knob 1 Turn this knob to set a programme.
The set of this function increases the programme duration. Spin button 8 Press this button to: • Decrease the maximum speed of the spin phase of the programme. • Activ ate the ‘No Spin’ func tion . Set this function to cancel all spin phases. The appliance does not spin the laundry.
Programme Temper atu re Type of load and soil Weight of load Programme phases Possible functions Wool 40° – Cold Machi ne wash abl e wool . Hand washa ble wool and delicate fabrics with «hand washing» care symbol. max. 1 kg Wash Rinses Spin phase at 800 rpm Handwash 30° C Hand washable delicate fabrics with «hand washing» care symbol.
Standard programmes for the Energy Label consumption values The cotton 60 °C economy and cotton 40 °C economy are the standard cotton programmes for normally soiled cot- ton laundry.
Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.7 >25 Before first use 1. To activate the drain system, put 2 litre of water in the main wash compartment of the detergent dis- penser.
2 The detergent compartment for the washing phase. If you use a liquid detergent, put it immedi- ately before you start the programme. Liquid additives compartment (fabric condi- tioner, starch). Put the product in the compartment before you start the programme.
If the temperature and level of the water in the drum are too high, you cannot open the door. To open the appliance door: • Do the steps 1 and 2 again. • Wait for some minutes. • Make sure that no water is in the drum. At the end of the programme • The appliance stops automatically.
Door seal Regularly examine the seal and remove all objects from the inner part. Detergent dispenser To clean the dispenser: • Press the lever and pull the dispenser out. • Remove the top part of the liquid additive com- partment. Clean all the parts wit h water.
6. Remove fluff and ob- jects from the pump. 7. Make sure that the impeller of the pump can turn. If th is does not occur, contact the service centre. 1 2 8. Clean the filter under the water tap and put it back in the pump. Caution! Make sure that you tighten cor- rectly the filter to prevent leakages.
Troubleshooting The start of the appliance does not occur or it stops dur- ing operation. First try to find a solution to the problem (refer to the ta- ble). If not, contact the service centre. Warning! Deactivate the appliance before you do the checks.
Problem Possible cause Possi ble s olutio n The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again.
Installation Unpacking 1 2 A 1. Use the gloves. With a scissor cut the straps and with a cutter remove the external film. Do not to discard the plastic cover (A). 2. Remove the polystyrene packaging materials. 3. Remove the internal film. 4. Open the door and remove all the items from the drum.
5. Put the front piece on the floor behind the appli- ance. Carefully put down the appliance with the rear side on it. Make sure not to damage the ho- ses. 1 2 6. Remove the polystyrene protection from the bot- tom. A 7. Install the plastic cover (A), removed from the top of the packaging, to the bottom of the appliance.
10. Replace the plastic spacers with the large plastic caps. You can find these large caps in the user manual bag. Warning! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance.
• On the edge of a sink. Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 90 cm.
www.zanussi.com/shop 155219130-A-202011.
デバイスZanussi ZWS 281の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zanussi ZWS 281をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZanussi ZWS 281の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zanussi ZWS 281の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zanussi ZWS 281で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zanussi ZWS 281を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZanussi ZWS 281の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zanussi ZWS 281に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZanussi ZWS 281デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。