Zebra TechnologiesメーカーTTP 8000の使用説明書/サービス説明書
ページ先へ移動 of 132
P1003638-003 Rev . A Zebra® TTP 8000 Kiosk Receipt Printer Technical Manual.
2 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 © 2009 ZIH Corp. The copyrights in this manual and th e software and/or firmware in the printer described therein are owned by ZIH Corp.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 Contents 1 • Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 4 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 4 • Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Inst alling a Paper Roll . . . . . . . . . . . . . . . . . . . .
5 Contents 10/19/2009 TTP 8000 T echnical Manual P1003638-003 8 • Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 6 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Notes • ___________ ____________________ _____________________ _______________ ___________ _____________________ ____________________ __.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 1 Introduction About This Manual This manual contai ns the information req uired to install the p rinter and to ru n it from a host computer such as a PC. The TTP 8000 series consists of TTP 8200 with a resolution of 203 dpi, and TTP 8300 wi th a resolution of 3 00 dpi.
About This Document Contacts 8 P1003638-003 TTP 8000 T echnical Manual 10/19/09 Contact s T echnical Supp ort via the In ternet is available 24 h ours per day , 365 days pe r year . W e b Site: www .zebra.com E-mail Back T e chni cal Library: E-mail address: emb@zebra.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 2 Product Presentation The TTP 8000 kiosk print er series consists of a fam ily of printers that will print A4 or Lett er paper width depending o n the printer config uration. Different configurati ons and paper handling o ptions are availa ble.
Product Present ation 10 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Figure 2 • Printer Exterior , Side View The TTP 8000 series of kiosk pr inters use direct thermal print ing.
11 Product Presentation 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Figure 3 • Printer Exterior , Rear View.
Product Present ation Indicators 12 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Indicators The status indi cator flashes in va rious sequen ces to indicate speci fic statuses or wa rnings.
13 Product Presentation Indicators 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Control Board Indicators The control board has tw o power indicators behi nd the power connecto r . T o see the indicators, open the printhead and lo ok down between the plate n and the printer frame.
Product Present ation Feed Button 14 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Feed Button When you hav e inserted the pape r under the printhead, press t he Feed butt on and the printe r will feed it forward, cut and eject a printout, then switch to on-line mode.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 3 Installation Unp acking When a new printer is delivered the printhead is secured with a shipping strap. Remove this by pressing it downwards and disengage it from the parallel i nterface hole, then turn it up and remove the shipping strap.
Inst allation Installation Considerations 16 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Inst allation Considerations There are a nu mber of printe r mounting options avail able to install the TTP 8000 printer in a self-service kiosk enclos ure , as illustrated in Figure 5 .
17 Installation Installation Considerations 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Electrost atic Discharges, and Earth Current s Preventing ESD and earth curren ts fro m affect ing the pr.
Inst allation Connecting to the Computer 18 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Connecting to the Computer Using the Parallel Interface 1. Connect the printer to the parall el port o f the computer to be used. 2. Connector J10 is an IEEE-1284 type C, 36-pole mini Centroni cs, with clip latches.
19 Installation Connecting to the Computer 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Using the USB Interface 1. Connect J13 of the printer to the USB port of th e computer or the USB hub to be used. USB connectors c an be recognized by the follo wing symbol: .
Inst allation Connecting to the Computer 20 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Connecting the Power 1. Attach a ground cable to the ground screw on the printer . 2. Connect the cab le from the power supply to J8. 3. Connect the power cable to th e line outlet.
21 Installation Making a T est Printout 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Making a T est Printout Y ou can make a self-test pr intout if you want to verify that the printer operates correct ly . See Self-test Prin tout and Other Powe r ON Modes on page 29 .
Inst allation Paper Path Adjustment 22 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Paper Level Sensors The printer has inpu ts for two paper leve l sensors.
23 Installation Installing a Printer Driver 10/19/2009 TTP 8000 T echnical Manual P1003638-003 If you use cust om designed paper h olders, connect the sensors according to Figure 1 1 .
Inst allation Installing a Printer Driver 24 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Notes • ___________ ____________________ _____________________ _______________ ___________ ___________.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 4 Operation.
Operation Installing a Paper Roll 26 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Inst alling a Paper Roll Prep arations 1. T urn the new paper roll a s shown. The pa per should be inserte d into the printer with th e temperature-sensitive side up.
27 Operation Installing a Paper Roll 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Using Auto Load 1. Make sure the pr inter is turne d ON. 2. Make sure the front edge of the paper is straight . 3. Enter the paper b etween the gui de wings and fee d it straight into the print er .
Operation Clearing Paper Jams 28 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 4. Press the Feed button and the paper will fee d , cut and eject a printout, and then automatically go online. Clearing Paper Jams Should a paper jam occur , follow the procedure belo w: 1.
29 Operation Self-test Printout and Other Power ON Mo des 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Self-test Printout and Other Power ON Modes 1. Remove power from the printer . If your printer has a power switch, turn the powe r off. If it does not, remove power to the printer .
Operation Self-test Printout and Other Power ON Modes 30 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Notes • ___________ ____________________ _____________________ _______________ ___________.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 5 Programming There are two dif ferent ways of setting up the printout: T ext oriented and driver oriented style.
Programming 32 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Figure 17 • Printout Styles.
33 Programming How the commands are described 10/19/2009 TTP 8000 T echnical Manual P1003638-003 How the commands are described Mnemonic Is the popular c ommand name that should be easy to remember Hex Give the command in hex representation Decimal Give the command in decimal representation Va l u e s n1, n2, etc.
Programming Summary Of Control Codes & Escape Sequences 34 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Summary Of Control Codes & Escape Sequences T able 6 • Control Codes and Escape .
35 Programming Summary Of Control Codes & Escape Sequences 10/19/2009 TTP 8000 T echnical Manual P1003638-003 ESC i n1 1B 69 n1 27 105 n1 It alics page 38 ESC J n1 1B 4A n1 27 74 n1 Paper Ad vance page 49 ESC j n1 1B 6A n1 27 106 n1 Paper Reverse page 49 ESC l 1B 6C n1.
Programming Software Command Syntax 36 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Sof tware Command Synt ax The commands in this sect ion are grouped after wh at the y do, and these groups are sorted in a theoretical usage sequence.
37 Programming T ext Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 T ext Commands T ext received by the printer is prin ted with the currently sele cted font and font attributes. T ext exceeding th e page width is wrapped with the line spacing selected.
Programming T ext Commands 38 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 This command selects on e of eight fonts. The font design depends on which fonts have been loaded 1 into the p rinter . Make a test printout to see which fonts are available in your printer .
39 Programming T ext Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Selects no rmal or reversed print . Single words, characters, or complete text lines c an be reversed. Characters, single words, or complete text lines can be underlined .
Programming T ext Commands 40 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Applicable n values are 0 — 7. In combination with v a ri able character height ( <ESC>h<n1> ), give high ly legible charact ers depending o n the font to which the command has be en applied.
41 Programming T ext Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Cancels text and attrib utes sent before the <CAN> command on the same lin e. Commands, are not cancelled. By default, carria ge return is ignored. By changing the default settin gs, you can: 1.
Programming T ext Commands 42 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 This command is use d to increase th e line spacing. Prints data from the input buf fer and feeds the pa per to the to p of the next page.
43 Programming T ext Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 This command defines the desire d horizontal tab positions. V ariables n1...nx represent each tab position . Up to 16 tab p ositions are allo wed. Minimum al lowed value is “1”.
Programming T ext Commands 44 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Sends one line of dot data. This command is used to bu ild images, one dot line a t a time by the printer driv er and should not be combin ed with text commands.
45 Programming T ext Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Sends one line of d ot data. This command is used to build images, one dot line at a time. Dat a compression The W indows drivers use line ba sed compression to decrease the t ime it takes to transfer graphics data to the p rinter .
Programming T ext Commands 46 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Prints a ruler li ne across the pape r . A ruler line is no rmally used to di vide the print out into logical parts to make it easier to read. A ruler line is actually an area defined by a star t X-Y position and a stop X-Y position.
47 Programming T ext Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Prints a customized logotype 2 stored in th e flash PROM . See also Logotypes on page 67 . ESC g n...n5 Print Logotype 1B 67 n1...n5 hex 27 103 n1...n5 decimal 2. For logotype lo ading, see "ESC & 1" under Syst em Relate d Commands on page 52 .
Programming T ext Commands 48 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Print commands This command makes th e printer print the contents of the li ne buffer . T ext is converted fro m text to pixe l lines and stored in the line b uffer wh en an <LF> is received.
49 Programming T ext Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 The value n represents the number of dot lines the paper is to be transported forwa rds. Range: 1–255. The value n represents the numb er o f dot lines the paper is to be tra nsported backwards.
Programming Cut and Present Commands 50 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Cut and Present Commands Effects a paper cut-off and an eject thro ugh the presenter module. The RS command automatically gives the ej ect length of 50 mm in additi on to the factor st ored in parameter p47.
51 Programming Cut and Present Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 <ESC><FF><n> ejects the document through the presen ter module. V ariable n represen ts the eject-length in steps. The se tting of parameter n47 is always added to the eject n in all forms of eject.
Programming System Related Commands 52 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 System Related Commands Restarts the printer with a complete reset. This is the same as power of f/on. T erminates the processing and initializes t h e co ntrol board.
53 Programming System Related Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Redirects any parameter storage init iated by <ESC>&<4> to another stora ge location. These settings can la ter be recalled by <ESC>&<F><n> .
Programming System Related Commands 54 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 This command resets t h e parameters o f the printer to default or any previously stored setup. T emporarily sets all parameters to predefined valu es that are stored in th e printer .
55 Programming System Related Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 This command should be used when you integrat e firmware loading into your kiosk program. ESC NUL Load Firmware 1B 00 Hex 27 0 Decima l Note • The T oobox program is a v ailable to lo ad firmware into th e printer from http://www .
Programming System Related Commands 56 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 S t atus reporting commands See also S tatus Reporting on page 69 . A status enquiry results in response ACK (6) if all sensors are clear , but NAK (15) + co de if one or more sensors report some condition.
57 Programming System Related Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 The host computer cannot be certai n that all conditions have been cleared un til an ACK is received.
Programming System Related Commands 58 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Requests mult iple bytes of in formation regarding loade d fonts and log o types.
59 Programming System Related Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Results in a 2-byte resp on se, reflecting the status of ea ch se nsor. This command is inte nded as a go/no go in dication. When ev erything is OK, this status report returns 0.
Programming System Related Commands 60 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Results in a 2-byt e response representi ng the version o f the installed fi rmware. The first byte re presents major versions, and the second byte minor v ersions.
61 Programming System Related Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Results in a 1-byte resp onse representi ng the temperature of the Printhead. Results in a 2-byt e response representi ng the versio n of the installe d bootware.
Programming System Related Commands 62 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Extended status is status from the printer together with de vices connected to the I 2 C options- bus available in some Zebra printers. The short me ssage protocol gives replie s up to 255 by tes.
63 Programming System Related Commands 10/19/2009 TTP 8000 T echnical Manual P1003638-003 This command reque sts information about the sett ing of paramete r n1, that is, the pa rameter value stored in fla s h PROM or any pa rameter value temporarily set b y other ESC comma n ds.
Programming Fonts 64 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Font s Loading The printer can st ore 8 fonts in it s flash PROM. 25 6 kB i s available for font storage. The font size is fixed 3 , so you must l oad one font file for each charac ter size you require.
65 Programming Fonts 10/19/2009 TTP 8000 T echnical Manual P1003638-003 File Format A font consists of a header desc ribing the font, then data for every characte r in the font. The header has to be downloaded ev en if the font consists of a single ch aracter only .
Programming Fonts 66 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Character Bitmap Dat a A character is made up of a bitmap the size of which is: Char .
67 Programming Logotypes 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Logotypes Up to 16 logo types can be stored in the flash PROM of the printe r .
Programming Logotypes 68 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Printing T o print a logoty pe, send <ESC>g<n1><n2><n3><n4><n5> where n1 is the logotype number , n2n3 is t he horizontal prin t position, and n4n5 is the vertical print position o f the upper left corner of the logoty pe.
69 Programming S tatus Reporting 10/19/2009 TTP 8000 T echnical Manual P1003638-003 S tatus Reporting The printer is equipped with a number of sensors that report the printer statu s and various conditions such as out- of-paper , previous printout not removed , etc.
Programming S tatus Reporting 70 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Notes • ___________ ____________________ _____________________ _______________ ___________ _____________________ _.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 6 Default Parameter Settings Some of the printe r settings ca n be stored in the flash PROM so that they will be used also after power OFF . The stored para meter settings are printed out on t he self-test printout (see Self-t est Printout and Other Power ON Modes on page 29 ).
Default Parameter Settings How the Parameters are Described 72 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 How the Parameters are Described Default value The default val ues indicated are "factory default settings" you ge t by sending <ESC>&<F><10> .
73 Default Parameter Settings How the Parameters are Described 10/19/2009 TTP 8000 T echnical Manual P1003638-003 T able 10 • Summary of Parameter Settings Parameter Description ESC&F <10>.
Default Parameter Settings Serial Interface Set-up 74 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Serial Interface Set-up Stores the communi cation speed on the serial interface. Selects if 7-bit ASCII, or 8-bit , is used on the serial inte rface.
75 Default Parameter Settings Serial Interface Set-up 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Select what handshaking to use on the serial interface. 4 2D e f a u l t Flow-control 0 Min 2M a x <ESC>&P<4><0> No flow control <ESC>&P<4><1> Xon / Xoff * *.
Default Parameter Settings Parallel Port Setup 76 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Parallel Port Setup Pins 12 and 15 on th e parallel port signal pap e r out and error .
77 Default Parameter Settings Print Setup 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Print Setup Controls wha t the printe r does with buffered data: Spooling all data makes the prin ter as quiet as possible. “Nothin g” happens until the bu ffer is full or a pr int trig gering comman d is receiv ed.
Default Parameter Settings Print Setup 78 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 The main reaso n to decrease the print spe ed is to enhance print quali ty, and to reduce the peak current consumption. Each step represents a 5 mm/s increase in TTP 8200 and 3.
79 Default Parameter Settings Print Setup 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Sto res 16 dif ferent T AB stop positions. The po sition is set in increments of 2. 5-mm. T ab position 255 sets a tab stop on the last posi tion of the line.
Default Parameter Settings Print Setup 80 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Decides if the printer sh ould cut after executing an FF command, or if it should just feed the form length.
81 Default Parameter Settings Print Setup 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Defines three diffe r ent things: 1. The minimum leng th of a page in variable do cument mode 2. The actual page length in fixed document mod e 3. The distance between black marks in black mark mode One step is 0.
Default Parameter Settings Fixed Document Mode 82 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Fixed Document Mode Max fixed document mode page le ngth depends on the amount of free ra m. Make a self test printout to ch eck how much is available in your p rinter .
83 Default Parameter Settings Fixed Document Mode 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Defines the distance between the top o f the paper and t he top of the first text li ne in 0.1 mm steps. The to p margin feed is effectua ted when th e present er is cleare d from the p revious pa ge.
Default Parameter Settings Fixed Document Mode 84 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 When the printo ut is printed and cut, the present er ejects about 50 mm of the page so th at the customer can grab it.
85 Default Parameter Settings Fixed Document Mode 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Selects if the c ut command cuts a t the position whe re the paper is at, or if the printer sho u ld advance the paper before cut t ing.
Default Parameter Settings Fixed Document Mode 86 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Y ou can lock the parameters so that they cannot be changed by the ESC & P command. Adds a delay between th e burning of blo cks in the prin thead.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 7 Page Setup.
Page Setup Printable Area 88 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Print able Area 030 8 TTP 8x 00 K io sk P rinter – Techni cal M a nua l 27 5.2.2 Text com m ands T ext received by t he print er is printed with the c urrently selected f ont and font attributes.
89 Page Setup Aligning Preprint and Thermal Print 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Aligning Preprint and Thermal Print The printer can synchron ize the cutting of the prin tout with black-mark s printed on the back of the paper .
Page Setup Parameters Used 90 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Parameters Used Parameter n34 Auto Cut When this paramete r is set to 2, "forced c u t at black mark" Th e printer always c uts when it detects a black mark, even i f no cut command has been received.
91 Page Setup Parameters Used 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Garbage, Black Mark and Out Of Paper Detection For every step the paper is fe ed, the bla ck mark sensor i s sampled to det ect garbag e, black marks or out of paper .
Page Setup Parameters Used 92 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Parameter n41 and n42 –B lack Mark Cut Offset After the black mark is detected (black t o white change) t h e printer fe eds another distance to place the pap er in cut posit ion.
93 Page Setup Black-mark Sensing from Within Windows 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Simple Calibration Process 1. Enable black mark mode by setti ng parameters n36 to n4 2 as described on the prev ious pages. 2. Load paper with black marks in to the print er 3.
Page Setup Black-mark Sensing from Within Wind ows 94 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Notes • ___________ ____________________ _____________________ _______________ ___________ __.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 8 Interface The printer has two in terfaces as standard, p arall el and USB. There are no selections to be made, but normally only one interface should b e used at a time. The printer may not function properly if da ta is received on mo re than one interface at a ti me.
Interface Parallel 96 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Parallel TTP 8000 series support I EEE-1284 Compatibili ty Mode and Reverse Nibble Mode.
97 Interface Parallel 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Error Signaling All errors that are not reset when status is re ad will set th e nFault sign al, for examp le: • Head lifted .
Interface USB 98 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 USB The USB (Unive rsal Serial Bus) is an i nterface designed to handle several pe ripherals through a single connector . The transfer speed is up to 12 Mbits/s, which is quit e adequate fo r the printer .
10/19/2009 TTP 8000 T echnical Manual P1003638-003 9 Maintenance.
Maintenance Fault Finding 100 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Fault Finding In connection with ser vice of the printer it is good practice to rem ove paper dust and l int from the paper path, cutter and sensor areas. Pape r dust, when accumu lated, may interfere with printer func tions such as optical sensors.
101 Maintenance Clean the Printhead 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Clean the Printhead The printhead can be cl eaned without re moval. 1. 2. 3. Caution • Disconnect the printer from the power source before performin g the following procedure.
Maintenance Firmware 102 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Firmware The firmware is stored i n flash-PROM on th e control board. Whe n replacing a co ntrol board, be sure to v erify the control board contains the same firmware version that you are currentl y using and upgrade it if n ecessary .
103 Maintenance Firmware 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Firmware TTP 8000 versio n Hardware version Firmware No. 200d pi 300 d pi St andard (with presenter) A – C (8-bit) 01749-x.
Maintenance Firmware 104 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Notes • ___________ ____________________ _____________________ _______________ ___________ _____________________ _________.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 10 Specifications.
Specifications General Information 106 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 General Information Print Dat a Serial Interface Settings Printer control W indows and Linux drivers. Direct addressing through ESC sequences. Plug and Play Y es Print method Direct thermal line printing Resolution 8x8 dots/mm (203 dpi) for TTP 8200 .
107 Specifications Paper Handling 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Paper Handling Paper supply Fan fold or roll paper Paper widt h A4 (210.2 mm) or Letter Size (8.5”) selectable by moving paper guides. Printout length 297 mm (A4) 148.
Specifications T ext Modes (Non-Windows Applications) 108 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 T ext Modes (Non-Windows Applications) Orientation Horizon tal (portrait mode), and vertica.
109 Specifications Character Sets 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Character Set s The default fonts use W indows code page 1252 W estern wh ich contains ISO 8859 -1 (ANSI) characters. Y ou can use other character sets by creating and loading appropriate font files.
Specifications Character Sets 110 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 T able 15 • Symbol Character T able.
111 Specifications Character Sets 10/19/2009 TTP 8000 T echnical Manual P1003638-003 T able 16 • Wingdings Character T able.
Specifications Character Sets 112 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 T able 17 • Code39 Character T able.
113 Specifications Printer Dimensions 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Printer Dimensions Figure 22 • Measurements Drawing, St andard Printer 0174 4-xxx and 01745-xx x Import ant • Additional space is required for pape r roll and handlin g.
Specifications Printer Dimensions 114 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Figure 23 • Measurement s Drawing, Compact Printer 01755-XXX.
115 Specifications Printer Dimensions 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Figure 24 • Measurements Drawing, V ertical Printer 01760-xxx with Combo Roll Holder 01861-21x for 150 mm Roll Under Printer Paper out 4 210 or 216 mm Paper 0 274 163 Roll, Ø150 mm Paper in, 48 0 72.
Specifications Printer Dimensions 116 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Figure 25 • 100W Power Supply Caution • Use only the recommended Zebra power supply (see Part Number List on page 124 for part number). Note • Y o ur printer may have a d ifferen t power supply .
117 Specifications Printer Dimensions 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Figure 26 • Combo Roll Holder 01861-21x for St andard, Compact, and V ertical V ersions of the Printer.
Specifications Printer Dimensions 118 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Figure 27 • Measurements Drawing, Printer 01744-xxx with Combo Roll Holder 01861-21x for up to 150mm Roll Beh.
119 Specifications Printer Dimensions 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Figure 28 • Measurements Drawing, Prin ter 01744-xxx with Roll Holder for 150 or 250mm Roll Under Printer.
Specifications Environmental Conditions 120 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Environment al Conditions Miscellaneous T emperature Operating: 0 to +50 °C St orage and transport ation.
121 Specifications Paper S peci fication 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Paper S pecification General Thermal Coating Perforation Paper supply Roll or fanfold paper with heat sensitiv e coating (thermal paper) T ype of paper T ypes of paper are listed o n www .
Specifications Paper S peci fication 122 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Preprinting Figure 29 • Forbidden Print Zones General T o endure the heat developed during printi ng, the preprint must meet the requireme nts applicable for p reprinting on pa per intended for la ser printing .
123 Specifications Paper S peci fication 10/19/2009 TTP 8000 T echnical Manual P1003638-003 Black Mark Size and Position Figure 30 • Recommended Black Mark Print on Back of Paper (Only the “22 mm Mark”) Print side Opposite to thermal coating side Sensor position 45 mm before cutter ,.
Specifications Part Number List 124 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Part Number List Printers Accessories Description NA/LA/AP EMEA TTP 8200 standard, cutter and present er 01744-21.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 11 中国 RoHS 材料声明 (China RoHS Material Declaration) 部件名称 有毒 / 有害物质或元素 铅 (PB) 汞 (Hg) 镉 (CD) 六价格 (CR6+).
126 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 Notes • ___________ ____________________ _____________________ _______________ ___________ _____________________ ____________________ _________.
10/19/2009 TTP 8000 T echnical Manual P1003638-003 Index A ACK 56 Acknowledge marker 63 Advance before cu t See Bottom margin Aligning prep rint and thermal print 89 Alignment 37 Ambient li ght 17 B B.
Index 128 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 D Data bits 74 , 106 Decimal codes 73 Default settings 71 Default settings store 52 Document Mo de BM 80 fixed 80 variable 80 Drawing print.
129 Index 10/19/2009 TTP 8000 T echnical Manual P1003638-003 O Operati on 25 Options-bus 62 ordering ribb on and media 8 Orientation 108 Out of paper 107 P Page setup 89 Page length 81 Paper advance 4.
Index 130 P1003638-003 TTP 8000 T echnical Manual 10/19/2009 S sales 8 Self-test 48 Self-test printout 21 , 29 Sensitivity 77 , 121 Sensor , paper-near -end 22 Sensors 57 , 107 , 123 status 59 Sensors.
.
Zebra T echnologies Corporation Zebra Technolo gies Corporation 475 Half Day Road, Suite 500 Lincolnshire, IL 6006 9 USA T: +1 847 63 4 6700 Toll-free +1 866 230 9494 F: +1 847 913 8766 Zebra T echnol.
デバイスZebra Technologies TTP 8000の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Zebra Technologies TTP 8000をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZebra Technologies TTP 8000の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zebra Technologies TTP 8000の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zebra Technologies TTP 8000で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zebra Technologies TTP 8000を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZebra Technologies TTP 8000の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zebra Technologies TTP 8000に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZebra Technologies TTP 8000デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
