ZenoahメーカーG270RCの使用説明書/サービス説明書
ページ先へ移動 of 32
OWNER'S MANUAL Thank you for using ZENOAH ENGINE. ● Please read this Owner’s Manual thoroughly before operating and use the engine correctly according to this Owner’s Manual. (For safety reasons, please contact your sales dealer before operating this engine if there is something that you do not understand.
2.
3 SPECIFICATIONS.....................................................4 SAFETY PRECAUTIONS..........................................5 FUEL .........................................................................7 ENGINE STARTING.......................
4 SPECIFICA TIONS Engine Type G240RC G270RC Overall Size (L x W x H) 166 x 205 x 196mm Weight 2.07kg Displacement 22.5cm 3 25.4cm 3 Clutch Engagement 6000rpm (STD Spring) Carburetor Type WT-813A Spark Plug NGK CMR7H Spark Plug Gap 0.
5 SAFETY PRECAUTIONS ● These safety precautions are to prevent you and those people in the vicinity from incurring harm or damage. Make sure to observe these precautions and constantly strive to ensure safety. ● Safe use of the engine is your personal obligation and responsibility.
6 SAFETY PRECAUTIONS overly long sleeves, neckties and the like. Failure to do so could result in injury. • When mounting the engine to a model, make sure to follow the model’s operating manual. If necessary, reinforce the engine mounting unit and the peripheral parts.
7 FUEL • Mix gasoline (octane over 95) and high grade 2 cycle engine oil (mixing use type; F3C grade or ISO EGC grade) at mixing ratio 25~40:1. • The mixing ratio is according to the oil recommendation. [ NOTE ] 1) Never use any alcohol fuel or alcohol added fuel, or the rubber parts in the carburetor and engine will be damaged.
8 ENGINE ST ARTING • Push the primer pump several times until overflown fuel flows out. (Fig.1) • Close the choke lever, and move the throttle lever 1/4~1/3 open position. (Fig.1)(Fig.2) • Pull the starter(knob) quickly until first firing noise.
9 OPERA TION • This engine is already tuned up to get high power and high speed, and needs correct maintenance to keep such high performance. • The details for operation may be described in the separate owners manual to be issued by car manufacturer.
10 MAINTENANCE 1) MAINTENANCE CHART Before Every Every Items Action Use 25 hours 100 hours Note Leakage, Check ✔ Damage/Crack Idling Speed Check/Adjust ✔✔✔ Air-cleaner Check/Cleaning ✔✔ Re.
11 MAINTENANCE 2) SPECIFICATIONS AND TECHNICAL DATA Items Unit G240RC G270RC Remarks Bore x Stroke mm 32 x 28 34 x 28 Displacement cm 3 22.5 25.4 Effective Compression Ratio 8.
12 MAINTENANCE 3) MAINTENANCE SPECIFICATIONS G240RC G270RC Items Standard Limit Standard Limit Measuring Device Remarks Bore (mm) ø32 Plating damaged ø34 Plating damaged Eye Checking Diameter (mm) ø31.97 ø31.87 ø33.97 ø33.87 Micro Meter Piston Ring 0.
13 MAINTENANCE 4) CARBURETOR Items Standard Limit Measuring Device Remarks Metering Lever set (mm) 1.65 ± 0.16 Vanier Inlet Valve Opening Pressure (kg/cm 2 ) 1.3~2.3 Leak Tester Inlet Valve Closing Pressure (kg/cm 2 ) 0.7~1.7 Leak Tester 5) IGNITION SYSTEM Items Standard Limit Measuring Device Remarks Spark Plug Air Gap (mm) 0.
14 MAINTENANCE 6) TIGHTENING TORQUE Items Screw Size Standard (N·m) Limit (N·m) Remarks Carburetor M5 (P=0.8) 3.4 2.9~3.9 Insulator M5 (P=0.8) 4.4 3.9~4.9 with Locktight glue Clutch M6 (P=1.0) 6.4 4.9~7.8 Rotor M8 (P=1.0) 12.7 9.8~14.7 Cylinder M5 (P=0.
15 SPECIAL TOOLS Part Name Part No. External Appearance Usage 1 Puller Assy 2890-96100 To remove rotor. 2 Piston Stopper 4810-96220 3 Rod Assy 1101-96220 To remove/install piston pin. 4 Air Gap Gauge 3330-97310 To set ignition coil. 5 Hex Wrench 3304-97611 6 Snap Ring Pliers 5500-96110 To remove snap ring.
16 SERVICE GUIDE 1) REMOVING CLUTCH SHOE 1. Remove the housing and plug cap. 2. Remove the spark plug and fit the stopper(4810- 96220) into the plug hole. 3. Remove clutch bolts(14mm Hex.). 2) REMOVING ROTOR (FAN) 4. Remove the rotor nut(12mm Hex.). 5.
17 SERVICE GUIDE 3) ASSEMBLING ROTOR Insert the gauge(3330-97310) in between the rotor magnet metal and the coil.Tighten screws while pressing the coil against the rotor. Air Gap 0.3 ~ 0.4mm 4) REMOVING PISTON PIN 1. Remove snap rings from both sides of the piston pin.
18 SERVICE GUIDE 5) INSTALLING PISTON 1. Make sure to point the arrow mark on the piston to the exhaust side. 2. Fit the circlip in the groove so as to face the end gap below. Deformed circlip may come off during engine operation and damage the engine.
19 TROUBLE SHOOTING 1) ENGINE DOES NOT START Description Cause Countermeasure No spark in the spark plug Spark Plug 1. Wet spark plug electrodes Make them dry 2. Carbon deposited on the electrodes Cleaning 3. Insulation failure by insulator damage Exchange 4.
20 TROUBLE SHOOTING 2) LACK OF POWER OR UNSTABLE RUNNING Description Cause Countermeasure Compression is normal 1. Air penetration from fuel pipe joints, etc Secure connection and no misfire 2. Air penetration from intake tube joint or Change gasket or tightening screws carburetor joint 3.
21 PA R TS LIST.
22 P ARTS LIST G240RC (X374323111).
23 G240RC (X374323111).
24 KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT 35 1140-21162 CASE, CLUTCH 1 36 3350-15250 BOLT 4 M5x16L 37 1140-55310 PLATE 1 38 0224-3061.
25 KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT 104 848ER883C0 • VALVE 1 105 1918-82160 • WASHER 1 107 T2070-31111 COVER, FAN 1 108 3310-12281 BOLT 4 M5x20L 109 848ER83111 COVER-A 1 110 1850-32160 SCREW 1 M4x12L 111 1900-31410 SCREW 2 TP4.
26 P ARTS LIST G270RC (X374326111).
27 G270RC (X374326111).
28 KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT 35 1140-21162 CASE, CLUTCH 1 36 3350-15250 BOLT 4 M5x16L 37 1140-55310 PLATE 1 38 0224-3061.
29 KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT KEY# PART NUMBER DESCRIPTION REMARKS Q'TY/ UNIT 104 848ER883C0 • VALVE 1 105 1918-82160 • WASHER 1 107 T2070-31111 COVER, FAN 1 108 3310-12281 BOLT 4 M5x20L 109 T2070-32100 COVER-A 1 110 1850-32160 SCREW 1 M4x12L 111 1900-31410 SCREW 2 TP4.
30 W ARRANTY WARRANTY TERMS 1) Scope of Application This engine manufactured by Husqvarna Zenoah Co., Ltd. (herein after “Zenoah”). And sold to the user directly or through distributor/manufacturer, shall entitle to be covered by this warranty. 2) Limits of Warranty Zenoah warrants that; 1.
31 W ARRANTY 4) Term of Warranty Three (3) months after purchased by end- user subject to 12 months from produced month. 5) Exempt from Warranty Zenoah shall not warrant this engine even if the fault has been caused during the period of terms of Warranty, in case that.
Head Office : 1-9 Minamidai, Kawagoe-city, Saitama, 350-1165 Japan Phone: (+81)49-243-1115 Fax: (+81)49-243-7197.
デバイスZenoah G270RCの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zenoah G270RCをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZenoah G270RCの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zenoah G270RCの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zenoah G270RCで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zenoah G270RCを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZenoah G270RCの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zenoah G270RCに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZenoah G270RCデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。