ZoomメーカーMRS-4の使用説明書/サービス説明書
ページ先へ移動 of 33
Thank you for purchasing the ZOOM MultiT rak Recording Studio MRS-4 (subsequently referred to as "the MRS-4 "). The MRS-4 offers the follo wing attracti ve features. ◆ Simultaneous 4-track playback/2-track recor ding 8 virtual takes per track add up to a total of 32 takes a vailable for recording.
Safety Precautions In this manual, symbols are used to highlight warnings and cautions for you to read so that accidents can be prev ented. The meanings of these symbols are as follows: This symbol indicates explanations about extremely dangerous matters.
The MRS-4 provides three types of ef fects: insert effect, mixdo wn ef fect, and send/return effect. These ef fects ha ve dif ferent characteristics, as described below . ■ Insert effect This effect operates directly after the input mixer . It is used to modify the input signal before it is recorded.
Parts of the MRS-4 ZOOM MRS-4 7 ZOOM MRS-4 Parts of the MRS-4 6 Parts of the MRS-4 T op panel Rear panel Front panel Display [TRACK P ARAMETER] key [SONG/UTILITY/TUNER] key [AUTO PUNCH IN/OUT] key [A-.
Power on/off switching To turn the MRS-4 on or off, proceed as follows. 1. Make sure that the MRS-4 and all other devices are turned off. T urn down the v olume at the source equipment, MRS-4, and monitor system. 2. Insert the SmartMedia card into the SmartMedia card slot on the front panel of the MRS-4, as described on page 5.
When you start to use the MRS-4 for recording, you must choose whether to create a new song or open an existing song for modif ication. 1. Connect the monitor system to the MASTER [L]/[R] jacks. To use headphones for monitoring, connect them to the [PHONES] jack.
The insert effect processes the signal from input 1/2 before it is sent to the tracks for recording. In this example, you apply the insert ef fect on the guitar signal supplied to the INPUT 1 jack. If you do not wish to use the insert effect, proceed to section 2-3 on page 15.
Record the guitar sound with insert effect on track 1, as follo ws. 1. Press the status key 1 r epeatedly , until the key is lit in r ed. The status keys 1 – 4 serv e for selecting the recording track, and for controlling the mute on/off condition for the track.
ZOOM MRS-4 17 5. When your guitar play is finished, press the STOP [ P ] key . The REC [ O ] key and PLA Y [ R ] key go out, and the recorder section stops. The display briefly shows "W AIT", and then the main screen reappears. The length of the "WAIT" interval dif fers, depending on recording conditions.
ZOOM MRS-4 19 The length of the "WAIT" interval depends on setting conditions. 6. To listen to the r ecording, use the ZERO [ U ] key to return to the beginning of the song, and then press the PLA Y [ R ] key . The recorded tracks 1 and 2 are played back.
The track mixer incorporates a send/return ef fect with rev erb/delay/chorus. The signal flo w when using the send/return effect is as follo ws. The intensity of the send/return effect can be adjusted for each track indi vidually by adjusting the send lev el.
2. Use the [P ARAMETER/VALUE] keys to select the algorithm and the setting value. The up/down [P ARAMETER/V ALUE] ke ys change the setting value. When the highest or lowest setting is reached, the unit switches to the ne xt algorithm. Pressing the left/right [P ARAMETER/V ALUE] keys changes directly to the next algorithm.
10. While playing the song, use the up/down [P ARAMETER/VALUE] keys to adjust the send level for that track. 11. Perform the same steps for other tracks. The mixdown ef fect serves to process the stereo signal produced by the track mix er . This effect can be used simultaneously with the send/return effect.
When the mixdown ef fect setting is completed, you are ready to record the f inal mix on the master recorder . 1. Use the ZERO [ U ] key to return to the beginning of the song. 2. Set the master recor der to the recor ding condition. 3. Press the PLA Y [ R ] key .
Combining multiple tracks (Bounce function) "Bounce" is a function that mixes the recorded content of sev eral tracks and records them on one or two tracks.
This section describes how to use manual punch-in/out to re-record a region of a previously recorded track. 1. Repeatedly press the status key of the track on which you want to punch-in/out, until the key is lit in red. 2. Raise the fader of the corresponding channel to a suitable position.
Moving to a desired point in a song (Locate function) Y ou can specify a location within the song in time units (minutes/seconds/milliseconds), and mov e to that location. 1. While the main screen is shown, press the right [P ARAMETER/ V ALUE] key once.
Specifying a mark directly 1. While the main screen is shown, press the left [P ARAMETER/ V ALUE] key once. The indication "MARK" flashes on the display , and the number of the nearest mark before the current location is shown. 2. Use the up/down [P ARAMETER/ V ALUE] keys to select the desired mark number .
Assigning two inputs to a track In the "Basic Operation" section, we learned how to record the signal from one input on one track. By using the input mixer , it is also possible to combine the signal from two inputs onto one track, or to record it on two tracks separately .
7. Use the [P ARAMETER/VALUE] keys to adjust the parameter . The left/right [P ARAMETER/V ALUE] keys serve for selecting the parameter and the up/down [P ARAMETER/V ALUE] ke ys for setting the value. • When wishing to use the send/return effect, press the [SEND/RETURN] key to set it to ON, and then select the algorithm and parameter ( ➝ p.
8. Specify the end point in the same way as described in step 6. 9. When you have specified the end point, press the [ENTER/YES] key . The screen for specifying the copy destination track and V -take appears. 10. Specify the copy destination track and V -take in the same way as described in step 4.
Use the left/right [P ARAMETER/V ALUE] ke ys to mov e the flashing section, and use the up/down [P ARAMETER/V ALUE] ke ys to change the number . 5. Press the [ENTER/YES] key . A screen will appear that allows you to set a start point for the erase action.
5. If necessary , specify the track number and V -take number , and press the [ENTER/YES] key . Use the left/right [P ARAMETER/V ALUE] ke ys to mov e the flashing section, and use the up/down [P ARAMETER/V ALUE] ke ys to change the number . Y ou can also specify a V - take that is currently not selected for the track.
4. Press the [ENTER/YES] key . The screen for the item selected in step 3 appears. The subsequent steps differ for each item. F or details, see the following section. Song menu items Operation steps for the various song items are described here. To create a new song on the SmartMedia card, proceed as follows.
Y ou can protect the currently selected song, so that no further recording or editing is possible. When a song is protected, you can still change effects or parameters, b ut you cannot store the results on the SmartMedia card. 1. From the song menu, select "ProtECt" and pr ess the [ENTER/ YES] key .
When the metronome is on and playback is started from a point midway in a song, no precount clicks are hear d. Depending on the start position, the metronome sound may start partly through a beat.
7. When tuning is complete, press the [EXIT/NO] key several times to r eturn to the main screen. Formatting a SmartMedia card Before starting to use an off-the-shelf SmartMedia card (designed for 3.3V , capacity 16 – 128 MB), you must first format it in the MRS-4 as follows.
Using the AUX IN jacks to save tracks A UX IN is an input that accepts an e xternal signal which is then mixed with the internal signal of the MRS-4 and output as is at the MASTER [L]/[R] jacks.
Specifications ZOOM MRS-4 57 Recorder Physical tracks: 4 V irtual takes: 32 (8 V -takes per track) Maximum number of simultaneous recording tracks: 2 Maximum number of simultaneous playback tracks: 4 Recording media: SmartMedia card 16 – 128 MB (3.
ZOOM MRS-4 59 ZOOM MRS-4 58 The recor ded sound is distorted • Check whether the input sensitivity setting ([INPUT LEVEL] controls 1/2) w as appropriate. •L o wer the track f aders or MASTER fader so that the 0 (dB) dot of the lev el meter does not light.
MIDI implementation chart MIDI implementation ZOOM MRS-4 61 ZOOM MRS-4 MIDI implementation 60 [Smartmedia Digital Recorder ] Date : 06.Jan.,2002 Model MRS-4 MIDI Implementation Chart Version :1.
Insert effect ••••••••••••••••••••••••••••••••••••••••••••• 5, 13 Algorithm •••••••••••.
ZOOM CORPORA TION NOAH Bldg., 2-10-2, Miyanishi-cho, Fuchu-shi, T okyo 183-0022, Japan PHONE: +81-42-369-7116 F AX: +81-42-369-7115 We b Site: http://www .
デバイスZoom MRS-4の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Zoom MRS-4をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZoom MRS-4の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Zoom MRS-4の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Zoom MRS-4で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Zoom MRS-4を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZoom MRS-4の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Zoom MRS-4に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZoom MRS-4デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。