ZyXEL Communicationsメーカー100WHの使用説明書/サービス説明書
ページ先へ移動 of 29
ZyXEL T OTAL I NTERNET A CCESS S OLUTION Prestige 100WH Internet Access Router Quick Start Guide.
Prestige 100WH Quick Start Guide ii Prestige 100WH Internet Access Router Copyright Copyright © 1998 by ZyXEL Communications Corporation. The contents of this publication may not be reproduced in any.
Prestige 100WH Quick Start Guide iii Table of Contents Chapter 1 Before You Begin ................................................................................................................. 1 1.1 Purpose Of This Guide ...........................
Prestige 100WH Quick Start Guide iv Chapter 5 Prestige Web Configurator Setup ..................................................................................... 21 5.1 Installing PWC Components ......................................................
Prestige 100WH Quick Start Guide 1 Chapter 1 Before You Begin 1.1 Purpose Of This Guide This guide provides instructions on how to setup your new Prestige and Windows 95/NT workstations for Internet access using the Prestige Web Configurator (PWC).
Prestige 100WH Quick Start Guide 2 1.3 Information From Your ISP Your Internet Service Provider (ISP) should provide information needed to setup your Prestige , usually in the form of an account configuration sheet. The information includes: l User name and password l ISP’s access phone number.
Prestige 100WH Quick Start Guide 3 1.4 Prestige’s Default TCP/IP Settings 1.4.1 IP Address and Subnet Mask Your Prestige is pre-configured in the factory with IP Address of 192.168.1.1 and subnet mask of 255.255.255.0 (Class C). 1.4.2 DHCP Setting Your Prestige has a built-in DHCP (Dynamic Host Configuration Protocol) server.
.
Prestige 100WH Quick Start Guide 5 Chapter 2 Cabling & Installation The following diagrams depict the cabling for the Prestige . After you have completed the cabling, proceed to Chapter 3: Windows 95 Quick Start or Chapter 4: Windows NT Quick Start .
Prestige 100WH Quick Start Guide 6 2.1.2 Front Panel LEDS The LED indicator lights on the front panel indicate the operational status of your Prestige . The following table describes the LED functions: LED Function Indicator Status Active Description PWR Power LED Green On Power is being applied to the Prestige .
Prestige 100WH Quick Start Guide 7 2.1.3 WAN Port Status LEDs CD (Carrier Detect) signal is sent by the WAN device to indicate that line negotiation is successful and that it is ready for data transfer. RTS (Request to Send) and CTS (Clear to Send) are hardware flow control signals.
Prestige 100WH Quick Start Guide 8 2.3 Prestige 100WH Connections POWER CONSOLE ETHERNET 4 3 2 1 WAN Ethernet LAN Computer Power Adapter Power Outlet Modem / ISDN TA Modem or ISDN TA PSTN/ISDN.
Prestige 100WH Quick Start Guide 9 Chapter 3 Windows 95 Quick Start This chapter shows you the step-by-step instructions to configure your Windows 95 workstations for Internet access. 3.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows 95 workstation before you can use it to access the Internet.
Prestige 100WH Quick Start Guide 10 Step 4. Select the Protocol item and click Add . Step 5. Choose Microsoft from the Manufacturers , and TCP/IP from the Network Protocols .
Prestige 100WH Quick Start Guide 11 3.2 TCP/IP Configuration Follow these steps to configure your TCP/IP for Windows 95. Step 1. From the Start Menu , select Settings then open Control Panel . Step 2. Double-click the Network icon to open the Network control panel.
Prestige 100WH Quick Start Guide 12 Step 3. The TCP/IP Properties dialog with IP Address tab will appear as shown belo w . Step 4. Select Obtain an IP address automatically if your ISP did not assign .
Prestige 100WH Quick Start Guide 13 Step 5. Select the WINS Configuration tab, and click Disable WINS Resolution . Step 6. On the Gateway tab, highlight any installed gateways and click the Remove button until there are none listed.
Prestige 100WH Quick Start Guide 14 Step 7. On the DNS Configuration tab, select Enable DNS . Enter a unique name for the workstation in the Host box. Enter your domain name in the Domain box if you have one. This field is optional and can be left blank.
Prestige 100WH Quick Start Guide 15 Chapter 4 Windows NT Quick Start This chapter shows you the step-by-step instructions to configure your Windows NT workstations for Internet access. 4.1 TCP/IP Installation You must first install TCP/IP protocol on each Windows NT workstation before you can use it to access the Internet.
Prestige 100WH Quick Start Guide 16 Step 4. Choose TCP/IP Protocol from the Network Protocol list. Then click OK . This will install the TCP/IP protocol on you workstation.
Prestige 100WH Quick Start Guide 17 4.2 TCP/IP Configuration Follow these steps to setup your TCP/IP configuration for Windows NT. Step 1. From the Start Menu , select Settings then open Control Panel . Step 2. Double-click the Network icon to open the Network control panel.
Prestige 100WH Quick Start Guide 18 Step 4. Select Obtain an IP address automatically if your ISP did not assign you a block of registered IP addresses (most cases).
Prestige 100WH Quick Start Guide 19 Step 5. On the DNS tab, Enter a unique name for the workstation in the Host Name box. Enter your domain name in the Domain box if you have one. This field is optional and can be left blank. Make sure the DNS Service Search Order box is blank if you plan to get the DNS server address( es) from a DHCP server.
Prestige 100WH Quick Start Guide 20 Step 6. On the WINS Address tab, make sure the toggle button of Enable DNS for Windows resolution is not checked. Step 7. Click on the OK button at the bottom to save and close the TCP/IP Properties dialog. Step 8. Click on the OK button to save and close the Network control panel.
Prestige 100WH Quick Start Guide 21 Chapter 5 Prestige Web Configurator Setup The Prestige Web Configurator (PWC) is a J AV A-based program that provides a quick, simple, and intuitive way to configure your Prestige .
Prestige 100WH Quick Start Guide 22 Note: The ZyXEL CD Installer Program (Startup.exe) requires the Microsoft ® V isual Basic 5 Runtime libraries. On some systems you may get the message "Error Starting Program" when trying to start the CD-ROM Installe r .
Prestige 100WH Quick Start Guide 23 Step 4. Open the J AV A Activator Control Panel located in the J AV A Activator 1.1 EA2 folder of your Start/Programs group.
Prestige 100WH Quick Start Guide 24 5.2 Starting the Prestige Web Configurator Step 1. To start PWC, select Start à Programs à ZyXEL à Prestige Web Configurator. Your web browser will start and show PWC’s welcome page. Step 2. Click the Wizard Setup button at the bottom of the welcome screen to start the Wizard Setup.
Prestige 100WH Quick Start Guide 25 Customer Support ZyXEL Prestige 100WH If you have questions about your ZyXEL products or desire assistance, contact ZyXEL Communications Corporation in one of the following ways. Contacting ZyXEL E-mail Technical Support Support@zyxel.
デバイスZyXEL Communications 100WHの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
ZyXEL Communications 100WHをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはZyXEL Communications 100WHの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ZyXEL Communications 100WHの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ZyXEL Communications 100WHで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ZyXEL Communications 100WHを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はZyXEL Communications 100WHの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ZyXEL Communications 100WHに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちZyXEL Communications 100WHデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。