BiostarメーカーA78MD 6.0の使用説明書/サービス説明書
ページ先へ移動 of 49
A75MD+/ A78MD Setup Manual FCC Information and Copyright This equipment has bee n tested and found to comply with the limit s of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are de signed to provide reasonable protection against harmful inte rference in a residential installation.
Table of Contents Chapter 1: In troduction ............................................................... 1 1.1 Before Y ou S tart......................................................................... 1 1.2 Package Che cklist .....................
A75MD+/A78MD 1 CHAPTER 1: INTRODUCTION 1.1 Before You Start Thank you for choosing our product. Before you st art installing the motherboard, please make sure you foll ow the instructions below: Prepare a dry and stable worki ng environment with sufficie nt lighting.
Motherboard Manual 2 1.3 Motherboard Specifications Specifications CPU Support Socket FM2+/FM2 for AMD A-series processor Maximum CPU TD P (Thermal Design Po wer): 100Watt * Please refer to www.
A75MD+/A78MD 3 1.4 Rear Panel Connectors Note 1: DVI-D / VGA Out put require an AMD famil y processor with intedrated graphics. Note 2: The mainboard supports two independent display outputs. Note 3: Since the audio chip supports High Definition Audio Specification, the function of each audio jack can be defined by software.
Motherboard Manual 4 1.5 Motherboard Layout Note: ■ represents the 1st pin..
A75MD+/A78MD 5 CHAPTER 2: HARDWARE INSTALLATION 2.1 Install Central Processing Unit (CPU) Step 1: Locate the CPU sock et on the motherboard Step 2: Pull the socket locking out from the socket and then raise the lever up to a 90-degree angel.
Motherboard Manual 6 Step 4: Hold the CPU do wn firmly , and then close the lever to locked the position 2.2 Install a Heatsink Step 1: Place the heatsink and fan assembly onto the retention frame. Mat ch the heatsink clip with the socket mounting- lug.
A75MD+/A78MD 7 2.3 Connect Cooling Fans These fan headers support cooling-fa ns bu ilt in the computer . The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the bl ack wire to pin#1.
Motherboard Manual 8 2.4 Install System Memory A. DDR3 Modules Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that t he notch on the DIMM matches the br eak on the slot.
A75MD+/A78MD 9 B. Memory Capacity DIMM Socket Location DDR3 Module T ot al Memory Size DDR3_A1 512MB/1GB/2G B/4GB/8GB/16GB DDR3_B1 512MB/1GB/2G B/4GB/8GB/16GB Max is 32GB.
Motherboard Manual 10 2.5 Expansion Slots PEX16_1: PCI-Express Gen3 x16 Slot - PCI-Express 3.0 compliant. - Maximum theoretical realized bandwidth of 16GB/s simultaneously per direction, for an aggregate of 32GB/s totally . - Only FM2+ processors can support PCIe 3.
A75MD+/A78MD 11 2.6 Jumper Setting The illustration sho ws how to set up jumpers. When the jumper cap is plac ed on pins, the jumper is “close”, if no t, that means the jumper is “open”.
Motherboard Manual 12 2.7 Headers & Connectors ATXPWR1: ATX Power Source Connector For better compatibility , we recommend to use a standard A TX 24-pin p ower supply for this connector . Make sure to find the correct orientation before plugging the connector .
A75MD+/A78MD 13 JPANEL1: Front Panel Header This 16-pin header includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connec t the PC case’s front p anel switch functions.
Motherboard Manual 14 JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel This header allo ws user to add additional USB ports on the PC front panel, and also can be connected with a wide range of external peripherals.
A75MD+/A78MD 15 F_AUDIO1: Front Panel Audio Header This header allo ws user to connect the front audio output cable with the PC front panel. This header supports HD and AC’ 97 audio front panel connector .
Motherboard Manual 16 CHAPTER 3: UEFI BIOS & SOFTWARE 3.1 UEFI BIOS Setup For better system performance, the UEF I BIOS firmware is being continuously updated.
A75MD+/A78MD 17 6. After the BIOS Update process is finished, click on OK to reboot the syste m. 7. While the system boots up and the fu ll screen logo shows up, please pr ess the <Delete> key to enter BIOS setup.
Motherboard Manual 18 2. Online Update Utility 1. Installing BIOS Update Utilit y from the DVD Driver . 2. Pleas e make sure the system is connected to the internet b efore using this function. 3. Open BIOS Update Utility and click the Online Update button on the main screen.
A75MD+/A78MD 19 8. While the system boots up and t he full screen logo shows up, press <Delete> key to enter BIOS setup. After entering the BIOS se tup, please go to the Save & Exit , using the Restore Defaults function to load Optimized Defaults, and select Sav e Changes and Reset to restart the computer .
Motherboard Manual 20 6. Select the proper BIOS file, and a message asking if you are sure to flash the BIOS file. Click Y es to start updating BIOS. 7. A dialog pop s out after BIOS flash is completed, asking you to re start the system. Press the [Y] key to restart syste m.
A75MD+/A78MD 21 3.3 Software Installing Software 1. Insert the Setup DVD to the optical dr ive. The driver installation program would appear if the Autorun function has bee n enabled. 2. Select Soft w are Inst allation , and then click on the respective software title.
Motherboard Manual 22 After filling up this information, click “ Send ” to send the mail out. A warning dialog would appear asking for your confirmation; click “ Send ” to confirm or “ Do Not Send ” to cancel. If you want to save this info rmation to a .
A75MD+/A78MD 23 BIOScreen Utility This utility allows yo u to personalize your boot logo easily . Y ou can choose BMP as your boot logo so as to customize your computer. Please follow the step-by-step instructions b elow to update boot logo: z Load Image : Choose the pict ure as the boot logo.
Motherboard Manual 24 CHAPTER 4: USEFUL HELP 4.1 Driver Installation After you installed your operating s ystem , please insert the Fully Setup Driver DVD into your optical drive and install th e driver for better system performance.
A75MD+/A78MD 25 4.2 AMI BIOS Beep Code Boot Block Beep Codes Number of Beeps Description Continuing Memory sizing error or Memory module not found POST BIOS Beep Codes Number of Beeps Description 1 Success booting. 8 Display memory error (system video a dapter) 4.
Motherboard Manual 26 CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the mot herboard will shutdown automatically to avoid a damage of the CPU, and the s ystem may not power on again.
A75MD+/A78MD 27 RAID 1: Data are stored twice by writing them to both the data disk (or set of data disks) and a mirror disk (or set of disks). If a disk fails, the controller uses either the data drive or the mirror drive for data recovery and continues operation.
Motherboard Manual 28 4.5 AMD DUAL Graphics Technology AMD Dual Graphics Technology Introduction When user adds a PCIE display adapter , it can be integrated with IGD to show better performance. T o make the two video devices work simultaneously and normally , please refer to the follo wing setting.
A75MD+/A78MD 29 AMD Dual Graphics Setup Step 1: Insert Dual Graphics-Ready grap hics card into PEX16_1 slot. Step 2: Set the BIOS setting as follows: [Chipset] → [North Bridge] → [GFX Configuration] → [Surround View] → [Enabled] Step 3: Install Driver DVD Chipset Driver , an d reboot the system.
Motherboard Manual 30 APPENDIX: Specifications In Other Languages Arabic تﺎﻔﺻاﻮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ةﺪﻋﺎﻗ ﺔﻳﺰآﺮﻤﻟا ﺬﺧﺄﻤﻟا FM2+/FM2 ى.
A75MD+/A78MD 31 تﺎﻔﺻاﻮﻤﻟا جرﺎﺨﻤﻟاو ﻞﺧاﺪﻤ ﻟا ﺔﻴﻠﺧاﺪﻟا ﺔﻠﺻو 4 x SATA 6 ﺖﻳﺎﺑﺎﺠﻴﺟ / ﺔﻴﻧﺎﺜﻟا عزﻮﻣ 2 x مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ USB 2.0 ) مﺎﻋ ﻞﺴﻠﺴﺘﻣ ﻞﻗﺎﻧ ﻦﻴﺘﺤﺘ ﻓ ﻞﻤﺤﺘ ﻳ عزﻮ ﻣ ﻞآ USB 2.
Motherboard Manual 32 French Spécif ications Support Unité Centrale Interface de con nexion FM2+/ FM2 pour série A AMD Envelop pe thermique Unit é Centra le maximum : 100W att * Veuillez vous re porter à www.bi ostar. com.t w pour la liste de s supports modèles d'Unité Central e.
A75MD+/A78MD 33 Spécif ications I/O en inte rne 4x Connecteur SATA 6. 0Gb/s 2x embase s USB 2.0 ( chaque emb ase suppo rte 2 Po rts USB 2 .0) 1x embases USB 3.
Motherboard Manual 34 German Spezifikationen CPU-Unterstützung Anschluss-FM2+/FM2 für A MD A-Serie Maxim ale CPU T DP (Therma l Desig n Power) : 100 Watt * Bitte konsult ieren Sie www.
A75MD+/A78MD 35 Spezifikationen Interne I/Os 4x SATA 6.0Gb/s- Verbinung 2x USB 2.0-Header (j eder Header unterstützt 2 USB 2.0-Ports) 1x USB 3.0-Header (j eder Header unterstützt 2 USB 3.
Motherboard Manual 36 Italian Specificazioni Supporto processore Slot FM2+ /FM2 pe r processore AMD seri e-A Alimentaz ione di Pro iezione Term ico (TDP – T hermal Desi gn Power): 100Watt * Si prega di consul tare www.biostar .com.tw per la lista di supporto del processore.
A75MD+/A78MD 37 Specificazioni Ingressi/ Uscite Interni Connettore 4x SATA 6.0 Gb/s Distributore 2 x USB 2.0(og ni distributor e supporta 2 sl ot USB 2.
Motherboard Manual 38 Japanese 仕様 CPU サポート AMD A- シリーズ プロセッサの Socket FM2+/FM2 最大 CPU TDP ( Thermal Design Power 最大放熱量) :100 W *CPU サポート リストについては、 www.
A75MD+/A78MD 39 仕様 内蔵 I/O 4x SATA6.0Gb/s コネクタ 2x USB 2.0 ヘ ッダー ( 各ヘッダーは、 2 つの USB 2.0 ポートをサポートしていま す ) 1x USB 3.
Motherboard Manual 40 Polish Specyfikacj e techniczne Obs ł uga proceso ra Gniazdo pr ocesora (Socket ) FM2+/FM2 dla pr ocesorów AMD s eria-A Moc Wydziela nego Ciep ł a (TDP - Therm al Design P ower): 100W att * Prosz ę sprawdzi ć list ę obs ł ugiwanych pro cesorów na stron ie interne towej www.
A75MD+/A78MD 41 Specyfikacj e techniczne Wewn ę trzne p orty wej ś cia/ wyj ś cia Z łą cza 4x SATA 6 .0Gb/s Z łą cza 2x USB 2.0 (ka ż de z łą cze obs ł uguje dodatkowe 2 po rty USB 2.0) Z łą cza 1x USB 3.0 (ka ż de z łą cze obs ł uguje dodatkowe 2 po rty USB 3 .
Motherboard Manual 42 Portuguese Especific ações Suporte Processador Porta FM2+/ FM2 para processa dor AMD série -A Alimentaç ão de Design Té rmico (TDP – Therm al Design Power ): 100Watt * Por favor consulte www.bios tar.com .tw para obter uma lis ta de supo rte do processador.
A75MD+/A78MD 43 Especific ações Conectores na placa Conector 4x SATA 6.0Gb /s Dispositivo 2x USB 2.0 (ca da Dispos itivo supor ta 2 por tas USB 2.0) Dispositivo 1 x USB 3.
Motherboard Manual 44 Russian Спецификации Поддержка центрального процессора Сокет FM2+/FM2 для процессоров AMD серии A Максим.
A75MD+/A78MD 45 Спецификации Внутр . Плата ввода - вывода Соединитель 4x SATA 6 Гб / с 2 контакта USB 2.0 ( каждый контакт поддерживает 2 порта USB 2.0) 1 контакта USB 3.
Motherboard Manual 46 Spanish Especific aciones Compatibilid ad con el procesa dor Ranura FM2+ /FM2 par a proce sador AMD serie - A Alimentaci ón de P royección Térmica (TDP – Thermal D esign Pow er): 10 0Watt *Por favor consultar con www.biostar.
A75MD+/A78MD 47 Especific aciones Conectores en placa Conector 4x SATA 6Gb’ s Distribuido r 2x USB 2.0 (cada dist ribuidor sopo rta 2 ranuras USB 2.0) Distribuido r 1x USB 3.
デバイスBiostar A78MD 6.0の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Biostar A78MD 6.0をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBiostar A78MD 6.0の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Biostar A78MD 6.0の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Biostar A78MD 6.0で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Biostar A78MD 6.0を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBiostar A78MD 6.0の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Biostar A78MD 6.0に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBiostar A78MD 6.0デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。