Bissellメーカー3574 Seriesの使用説明書/サービス説明書
ページ先へ移動 of 16
USER’S GUIDE 3574/3576 SERIES Safety Instructions 3 Product View 4 Assembly Instructions 5-6 Operation / Special T ools 6-8 Maintenance 8-12 T roubleshooting 12-13 Warranty 16 Replacement Parts 14 Consumer Services 15 CleanView ® II BAGLESS DJ68-00280A REV(0.
2 Thanks For Buying A BISSELL CleanV iew ® II We’ re glad you purchased a BISSELL CleanView II Vacuum. Everything we know about floor care went into the design and construction of this complete , high-tech home vacuuming system. Y our BISSELL CleanView II is well made, and we back it with a limited comprehensive one-year warr anty .
3 IMPOR T ANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precautions should be observed, inc luding the following: READ ALL INSTRUCTIONS BEFORE USING Y OUR UPRIGHT V ACUUM. Always connect to a polarized outlet (left slot is wider than right).
4 C AUTION: Do not plug in your vacuum cleaner until you are familiar with all instructions and operating pr ocedures. Power Switch Carrying Handle Crevice T ool Post-Motor Filter Quick Reach ® Handl.
The only tool you’ll need to assemble your vacuum cleaner is a screwdriver . Locate the vacuum Handle and remove the screw packet taped to the base of the Handle. Stand the vacuum upright and slide the base of the Handle firmly into the grooves at the top of the vacuum body .
Press the Handle Release Pedal with your foot to place your vacuum in one of three cleaning positions. Upright- For storage and above floor cleaning with tools. Normal Cleaning- Press Handle Release Pedal once. Use for most household floor cleaning tasks.
Y our BISSELL CleanView II is not only a pow- erful carpet and rug vacuum cleaner , it’ s also a versatile above floor vacuum cleaner when you select one of the special tools. Raise Handle to Upright Position. Grasp the Quick Reach Handle and lift Hose Wand to separate from suction intake opening.
T o maintain maximum cleaning performance, the following maintenance steps must be performed: Empty the Dirt Container when the dirt reaches the “Full” line on the side. Check the Inner and Outer Circular Filters and the Pre-Motor Filter at least once a month and clean or replace as needed.
Separate the Outer foam and Inner pleated Circular Filters. Wash each individually by hand in warm water . Mild detergent may be used if desired. Rinse well, then air dry thoroughly before putting them back together and replacing in Filter Cup. The Filter Cup may be washed in warm water with a mild detergent.
For standard models , remove the four screws as shown with a Phillips Head Screwdriver . Lift the Brush Cover off. For wide cleaning path models , Lift tab 1 and release the three latches in order 2-4 as marked. Lift the Brush Cover off. Grasp Rotating Floor Brush at both ends and lift.
Determine the light bulb type of your vacuum: Standard Bulb (#203-1297) – approximately 1” long, flat end Large Bulb (#203-1007) – approximately 2” long, round end Standard Bulb – remove the bulb from the socket by grasping bulb and pulling straight out.
12 T roubleshooting Vacuum c leaner won’t run P ossible Causes Remedies P ower cord not plugged in Check electrical plug Blown fuse/tripped breaker Check/Replace fuse or reset breaker Vacuum c leane.
Vacuum c leaner won’t pick up dirt continued P ossible Causes Remedies Dirt Container not installed properly Position correctly and lock in place F ilters are dirty Check and clean Inner and Outer C.
14 Replacement P arts – BISSELL Cleanview II Series 1 2/3 4 5 6 8/9 10 11 12 14 15 16 17 13 7 Y ou may purchase replacement parts from your retailer , by calling BISSELL Consumer Services or by visiting our website.
BISSELL Consumer Services For information about repairs or replacement parts, or questions about your warranty , call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. — 10 p.m. ET Saturday 9 a.m. — 8 p.m. ET Or write: BISSELL Homecare Inc .
Warranty 16 This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover , please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
デバイスBissell 3574 Seriesの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bissell 3574 Seriesをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBissell 3574 Seriesの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bissell 3574 Seriesの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bissell 3574 Seriesで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bissell 3574 Seriesを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBissell 3574 Seriesの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bissell 3574 Seriesに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBissell 3574 Seriesデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。