Black & Deckerメーカー3680の使用説明書/サービス説明書
ページ先へ移動 of 16
3680 12" Compound Miter Saw Instruction Manual TM.
Getting the most out of your tool. Please take time to read this manual and pay particular attention to the safety rules we’ve provided for your protection.
1 W W A A R R N N I I N N G G : : When using Electric Tools, basic safety precautions should always be followed to reduce the risk of fire, shock, and personal injury, including the following: R R E E A A D D A A L L L L I I N N S S T T R R U U C C T T I I O O N N S S 1.
F F o o r r y y o o u u r r c c o o n n v v e e n n i i e e n n c c e e a a n n d d s s a a f f e e t t y y , , t t h h e e f f o o l l l l o o w w i i n n g g w w a a r r n n i i n n g g l l a a b b e e l l s s a a r r e e o o n n y y o o u u r r m m i i t t e e r r s s a a w w .
sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box.
4 T ransporting the Saw TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. In order to conveniently carry the miter saw from place to place, a carrying handle has been included on the top of the saw arm. To transport the saw, lower the arm and depress the lock down pin shown in Figure 2.
5 M M i i t t e e r r P P o o i i n n t t e e r r A A d d j j u u s s t t m m e e n n t t TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. 1. Loosen the miter clamp knob and squeeze the miter latch to move the miter arm to the 0 position, as shown in Figure 7.
Plug the saw into any 120 volt 60 Hz power source. Be sure the cord will not interfere with your work. Switch To turn the saw ON, depress the trigger switch- Figure 13. To turn the tool OFF, release the switch. There is no provi- sion for locking the switch ON, but a hole is provided in the trigger for insertion of a padlock to lock the saw OFF.
Ensure that material does not creep while cutting, clamp it securely in place. Always let the blade come to a full stop before raising the arm. If small fibers of wood still split out at the rear of the work piece, stick a piece of masking tape on the wood where the cut will be made.
V ernier Scale Your saw is equipped with a vernier scale for added precision. The vernier scale allows you to accu - rately set miter angles to the nearest 1/4˚ (15 minutes). To use the vernier scale follow the steps listed below. (As an example, let’s assume that the angle you want to miter is 24 1/4˚ right).
Cutting Base Molding ALWAYS MAKE A DRY RUN WITHOUT POWER BEFORE MAKING ANY CUTS. Straight 90˚ cuts –Position the wood against the fence and clamp it in place as shown in Figure 19. Turn on the saw, allow the blade to reach full speed and lower the arm smoothly through the cut.
0 5 10 15 20 25 30 35 40 45 0 5 10 15 20 25 30 35 40 45 5 10 15 20 25 30 3 5 40 45 5 10 15 20 25 30 3 5 40 5 10 15 20 25 30 35 40 45 50 5 5 60 65 70 75 80 85 5 10 15 20 25 30 35 4.
I I N N S S I I D D E E C C O O R R N N E E R R : : Left side: 1.Miter right at 45° 2. Save the right side of cut Right side: 1.Miter left at 45° 2. Save left side of cut O O U U T T S S I I D D E E C C O O R R N N E E R R : : Left side: 1.Miter left at 45° 2.
Recommended accessories for use with your tool are available at extra cost from your distributor or local service center. A complete listing of service centers is included with your tool. C C A A U U T T I I O O N N : : The use of any non-recommended accessory may be hazardous.
IMPORT ANT! To assure product safety and reliability, particularly for Double Insulated tools, repairs, maintenance and adjustment (excluding maintenance described in this manual) should be performed by B&D ser- vice centers or authorized service centers, using identical B&D replacement parts.
Black & Decker (U.S.) Inc. • 701 East Joppa Road, Towson, Maryland 21286 Printed in U.S.A. (JAN94-CD-1) Form No. 159185 Copyright © 1994 .
デバイスBlack & Decker 3680の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Black & Decker 3680をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBlack & Decker 3680の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Black & Decker 3680の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Black & Decker 3680で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Black & Decker 3680を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBlack & Decker 3680の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Black & Decker 3680に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBlack & Decker 3680デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
