Black BoxメーカーMDS933AE-10BTの使用説明書/サービス説明書
ページ先へ移動 of 25
User Manual MDS932AE-10BT STANDALONE MDS932AE-FXO STANDALONE MDS932AE-FXS STANDALONE MDS933AE-10BT STANDALONE MDS932C-10BT RACK-CARD MDS933C-10BT RACK-CARD G.
.
User Manual VERSION CONTROL .......................................................................................................... 5 1 GENERAL INFORMATION........................................................................................ 6 ORDER INFORMATION .
User Manual 8.4 Line1 and Line2 Connector ............................................................................. 24 9 DESCRIPTION OF INTERFACE CABLES .............................................................. 25 9.1 Ethernet cable .........
User Manual VERSION CONTROL Version Date Major changes to previous version 1.0 31.12.2001 Initial version of the manual corresponding to version 1.2 of the device micro program 1.1 23.10.2003 New function description corresponding to software release V1.
User Manual 1 GENERAL INFORMA TION • High-speed symmetrical data transmission over one physical copper twisted pair with the 135 Ohm impedance according to ETSI TS 101 135.
User Manual ORDER INFORMA TION MDS932AE-10BT Modem AccessDSL Discovery, G.shdsl, 10/100Ba se-T Bridge, VLAN, Adapter 220 Vac MDS933AE-10BT Modem AccessDSL Discovery, G.shd sl, 1 or 2 pairs, up to 4.6Mbps, 10/100Base-T Bridge, VLAN, Adapter 220 Vac MDS932AE-FXS Modem AccessDSL Discovery, G.
User Manual 2 DESCRIPTION OF THE DEVICE 2.1 Exterior design Desktop models The front panel of the device has 3 LEDs: LOCAL informs the user about the status of the local device. The following four statuses are possible «blinking red» informs the user about malfunctioning of the modem’s hardware and software.
User Manual The back panel of the MDS932AE-10BT and MDS933AE-10BT modem has: • The grounding bolt of the modem (option); • The “AC12V” power connector.
User Manual 2.2 Exterior design rack card models.
User Manual Status(L) informs the user about the status of the local device. The following four statuses are possible «blinking red» informs the user about malfunctioning of the modem’s hardware and software. In this case, the modem is out of order and should be submitted to the service center for being repaired.
User Manual 3 RULES OF SWITCHING 3.1 The standalone delivery set The delivery set includes: • the subscriber access dev ice (a modem) • the power supply source (an AC adapter) • the cables for the line connections 3.
User Manual To update the information on the screen use the “Enter” key. The following menu will appear on the screen. Input Password: Please enter your programmed password. The unit will be delivered with the default password “admin” After entering the password the following menu will appear.
User Manual 4 THE COMMAND SYSTEM 4.1 Basic rules After the command is typed, press <enter>. The <Backspace> key is used to edit commands. It is necessary to input item number, for choising.
User Manual 4.3 Performance management submenu Upon activation of the performance management submenu the following message will be displayed. Performance Management 1.Loop Status... 4.EtherNet Status... Select item number or ESC to Upper level menu>> 4.
User Manual 4.3.2 Ethernet Status submenu Upon activation of the performance management submenu the following message will be displayed. Performance Management->EtherNet Status Link:Link down Link .
User Manual 4.4.1 DSL Setup In this menu you can setup the DSL link. When you have selected that menu, the following will appear: Configuration Management->DSL Setup 1.[Loop 1 Operation Mode]:Slave 2.[Loop 1 Auto/Fixed]:Fixed 5.[Loop 1 Fixed Connection Speed]:2312K(36N) 6.
User Manual 4.4.1.4 Fixed Connection Speed (only if Fixed is selected) • In the Fixed Connection Speed menu, you can specify your desired speed in the range of 72 kbps to 2312 kbps for 2wire units and 144 kbp s to 4624 kbps for 4wire models 4.4.1.5 Annex • With the Appendix menu you can choose between A, B, A / B.
User Manual 4.4.2 Ethernet Setup submenu Configuration Management->EtherNet Setup 1.[Speed]:Auto 2.[Duplex Mode]:Auto 3.[Disable Mac Filter]:No 4.IP Address>>192.168.5.105 5.Subnet Mask>>255.255.255.0 6.Gateway Address>>192.168.5.
User Manual 5 TECHNICAL SPECIFICA TIONS The main technical specifications of modems of the Black Box family are presented below in the table. Line interface.
User Manual 6 ST ORAGE CONDITIONS The equipment of the Black Box family while being packed should withstand all means of transport at a temperature in the range form -50 о С to +50 о С and the relative humidity of air up to 100% at 25 о С . The equipment can also withstand air-transport at a low air pressure of 12 kPa (90 Torr) at -50 о С .
User Manual 7 TERMS TO TRANSPORT The equipment of the Black Box family should be packed and transported by: • motor transport with an enclosed truck body; • enclosed railroad cars; • unpressurized airplanes and helicopters (up to 10000 m at an air pressure of 170 Torr); • river transport (in holds).
User Manual 8 CONNECT OR’S DESCRIPTION 8.1 DSL Connector Type: RJ-45, 8 pin Number Signal Assignment 1,2 NC - 3 LB,a Ttp (4W model only) 4 LA,a tip 5 LA,b ring 6 LB,b ring (4W model only) 7,8 NC - RJ-45 1 8 8.
User Manual 8.3 PC and Hub Connectors Type: RJ-45 Number PC assignment HUB assignment 1 Tx+ Rx+ 2 Tx- Rx- 3 Rx+ Tx+ 4 NC NC 5 NC NC 6 Rx- Tx- 7 NC NC 8 NC NC 18 RJ-45 8.4 Line1 and Line2 Connector Type: RJ-11, 4 pin Number Signal Assignment 1 NC - 2 LA,a tip 3 LA,b ring 4 NC - RJ-11 1 4 Version: 1.
User Manual Version: 1.2 Page. 25 of 25 9 DESCRIPTION OF INTERF ACE CABLES 9.1 Ethernet cable Side А Color of wire Side B 1 white/green 1 2 green/white 2 3 white/orange 3 4 blue/white 4 5 white/blue 5 6 orange/white 6 7 white/brown. 7 8 brown/white 8 9.
デバイスBlack Box MDS933AE-10BTの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Black Box MDS933AE-10BTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBlack Box MDS933AE-10BTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Black Box MDS933AE-10BTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Black Box MDS933AE-10BTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Black Box MDS933AE-10BTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBlack Box MDS933AE-10BTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Black Box MDS933AE-10BTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBlack Box MDS933AE-10BTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。