BMWメーカー320i xDrive Sedan (2014)の使用説明書/サービス説明書
ページ先へ移動 of 248
Owner's Manual for Vehicle The Ultimate Driving Machine T H E B M W 3 S E R I E S S E D A N . O W N E R ' S M A N U A L . Contents A-Z Online Edition for Part no.
.
3 Series Owner's Manual for Vehicle Thank you for choosing a BMW. The more familiar you are with your vehicle, the better control you will have on the road. We therefore strongly suggest: Read this Owner's Manual before starting off in your new BMW.
© 2013 Bayerische Motoren Werke Aktiengesellschaft Munich, Germany Reprinting, including excerpts, only with the written consent of BMW AG, Munich. US English VI/13, 07 13 490 Printed on environmentally friendly paper, bleached without chlorine, suitable for recycling.
Contents The fastest way to find information on a partic‐ ular topic or item is by using the index, refer to page 238 . 6 Notes At a glance 12 Cockpit 16 iDrive 24 Voice activation system 27 Integra.
Notes Using this Owner's Manual The fastest way to find information on a partic‐ ular topic is by using the index. An initial overview of the vehicle is provided in the first chapter.
Updates made after the editorial deadline Any updates made after the editorial deadline for the Owner's Manuals are located in the ap‐ pendix of the printed quick reference for the vehicle. For your own safety Maintenance and repairs Advanced technology, e.
▷ Federal Emissions System Defect War‐ ranty. ▷ Federal Emissions Performance Warranty. ▷ California Emission Control System Lim‐ ited Warranty. Detailed information about these warranties is listed in the Service and Warranty Information Booklet for US models or in the Warranty and Service Guide Booklet for Canadian models.
cating in an emergency, enable certain vehicle data to be transmitted from the vehicle. Event Data Recorder EDR This vehicle is equipped with an event data re‐ corder EDR.
Online Edition for Part no. 01 40 2 911 066 - VI/13.
At a glance These overviews of buttons, switches and displays are intended to familiarize you with your vehicle. You will also become quickly acquainted with the available control concepts and options.
Cockpit Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Front fog lamps 92 Parking lamps 89 Low beams 89 Automatic headlamp con‐ trol 90 Daytime running lights 90 Adaptive Light Control 90 High-beam Assistant 91 .
All around the center console 1 Headliner 15 2 Control Display 16 3 Ventilation 148 4 Hazard warning system 220 Central locking system 35 5 Glove compartment 158 6 .
All around the headliner 1 Intelligent Emergency Re‐ quest 220 2 Glass sunroof, powered 45 3 Indicator lamp, front passenger airbag 96 4 Reading lamps 92 5 Interior lamps 92 Seite 15 Cockpit At a glance 15 Online Edition for Part no.
iDrive Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
2. Press. 3. Move in four directions. Buttons on controller Press the but‐ ton Function MENU Open the main menu. RADIO Opens the Radio menu. MEDIA Opens the CD/Multimedia menu. NAV Opens the Navigation menu. TEL Opens the Telephone menu. BACK Displays the previous panel.
Press the but‐ ton Function BACK Open previous panel. OPTION Opens the Options menu. Operating concept Opening the main menu Press the button. The main menu is displayed. All iDrive functions can be called up via the main menu. Selecting menu items Menu items shown in white can be selected.
Additional options: move the controller to the right repeatedly until the "Options" menu is displayed. Options menu The "Options" menu consists of various areas: ▷ Screen settings, e.g., "Split screen". This area remains unchanged.
Function Controls Interactive map. Slide in the correspond‐ ing direction. Enlarge/shrink in‐ teractive map. Drag the display inwards or outwards with the fin‐ gers. Display menu. Tap once. Changing settings Settings on the control display, such as the volume, can be made via the touchpad.
Radio symbols Symbol Meaning Satellite radio is switched on. Telephone symbols Symbol Meaning Incoming or outgoing call. Missed call. Wireless network reception strength. Symbol flashes: network search. Wireless network is not available. Bluetooth is switched on.
Programmable memory buttons General information The iDrive functions can be stored on the pro‐ grammable memory buttons and called up di‐ rectly, e.g., radio stations, navigation destina‐ tions, phone numbers and entry points into the menu. The settings are stored for the remote control currently in use.
Symbol Function Enter the letters. Enter the numbers. or Move the controller up. Without navigation system Select the symbol. Entry comparison Entry of names and addresses: the selection is narrowed down every time a letter is entered and letters may be added automatically.
Voice activation system Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Executing functions using short commands Functions on the main menu can be performed directly by means of short commands, nearly irrespective of which menu item is currently selected, e.g., ›Vehicle status‹. List of short commands of the voice activation system, see Navigation, Entertainment, Com‐ munication Owner's Manual.
Notes on Emergency Requests Do not use the voice activation system to ini‐ tiate an Emergency Request. In stressful situa‐ tions, the voice and vocal pitch can change. This can unnecessarily delay the establish‐ ment of a telephone connection. Instead, use the SOS button, refer to page 220 , in the vicinity of the interior mirror.
Integrated Owner's Manual in the vehicle Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e.
Context help - Owner's Manual to the temporarily selected function The relevant information can be opened di‐ rectly. Opening via the iDrive To move directly from the application on the Control Display to the options menu: 1. Press the button or move the control‐ ler to the right repeatedly until the "Options" menu is displayed.
Seite 29 Integrated Owner's Manual in the vehicle At a glance 29 Online Edition for Part no. 01 40 2 911 066 - VI/13.
Online Edition for Part no. 01 40 2 911 066 - VI/13.
Controls This chapter is intended to provide you with information that will give you complete control of your vehicle. All features and accessories that are useful for driving and your safety, comfort and convenience are described here. Online Edition for Part no.
Opening and closing Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Take the used battery to a recycling center or to your service center. New remote controls You can obtain new remote controls from your service center.
Profile management Opening the profiles A different profile can be called up than the one associated with the remote control cur‐ rently in use. 1. "Settings" 2. "Profiles" 3. Select a profile. Called up profile is assigned to the remote control being used at the time.
▷ CD/Multimedia: audio source listened to last. ▷ Unlocking/locking of the vehicle: settings. ▷ Driving Dynamics Control: sport program ▷ Driver's seat position: automatically re‐ trieved after unlocking. ▷ Programmable memory buttons: assign‐ ment.
Opening and closing: from the outside Using the remote control General information Take the remote control with you People or animals left unattended in a parked vehicle can lock the doors from the in‐ side. Always take the remote control with you when leaving the vehicle so that the vehicle can then be opened from the outside.
If this occurs, lock or unlock the driver's door at the door lock using the integrated key. For US owners only The transmitter and receiver units comply with part 15 of the FCC/Federal Communication Commission regulations. Operation is gov‐ erned by the following: FCC ID: ▷ LX8766S.
Opening and closing: from the inside Locking and unlocking Pressing the buttons locks and unlocks the doors and the trunk lid when the front doors are closed, but they are not secured against theft.
Do not place the remote control in the cargo area Take the remote control with you and do not leave it in the cargo area; otherwise, the re‐ mote control is locked inside the vehicle when the trunk lid is closed.◀ Locking separately The trunk lid can be locked separately with the switch in the front passenger glove compart‐ ment.
Unlocking Grasp the door handle on the driver's or front passenger door completely, arrow 1. This corresponds to pressing the button on the remote control. Locking Press the area on the door handle, arrow 2, with your finger for approx. 1 second.
2. Move foot in the direction of travel under‐ neath the bumper and immediately back. Opening The trunk lid opens, regardless of whether it was previously locked or unlocked. During opening, the trunk lid pivots back and up. Ensure that adequate clearance is available before opening.
The vehicle locks automatically after you drive away. Retrieving the seat and mirror settings The driver's seat and exterior mirror positions used last are stored for the remote control cur‐ rently in use. When the vehicle is unlocked, these positions are automatically retrieved if this function was activated.
Switching off the alarm ▷ Unlock the vehicle using the remote con‐ trol. ▷ With Comfort Access: If you are carrying the remote control with you, pull on the driver side or front passenger side door handle. Indicator lamp on the interior rearview mirror ▷ The indicator lamp flashes briefly every 2 seconds: The system is armed.
Opening ▷ Press the switch to the resistance point. The window opens while the switch is held. ▷ Press the switch beyond the resist‐ ance point. The window opens automatically. Pressing the switch again stops the motion. Convenient opening, refer to page 36 , via the remote control.
Switching on and off Press the button. The LED lights up if the safety func‐ tion is switched on. Safety switch for rear operation Press the safety switch when transport‐ ing children in the rear; otherwise, injury may result if the windows are closed without super‐ vision.
The glass sunroof and sliding visor open automatically. Pressing the switch again stops the opening motion. Analogously, the glass sunroof is closed by sliding the switch forward. The sliding visor remains open and can be closed by hand. Convenient operation, refer to page 36 , via the remote control.
Adjusting Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Height Pull the lever and apply your weight to the seat or lift it off, as necessary. Backrest tilt Pull the lever and apply your weight to the backrest or lift it off, as necessary.
2. Height. 3. Seat tilt. 4. Backrest tilt. Thigh support Pull the lever at the front of the seat and adjust the thigh support. Lumbar support The curvature of the seat backrest can be ad‐ justed in such a way that it supports the lumbar region of the spine.
Front seat heating Switching on Press the button once for each tem‐ perature level. The maximum temperature is reached when three LEDs are lit. If the drive is continued within approx. 15 mi‐ nutes, the seat heating is activated automati‐ cally with the temperature selected last.
Putting on the belt Lay the belt, without twisting, snugly across the lap and shoulders, as close to the body as possible. Make sure that the belt lies low around the hips in the lap area and does not press on the abdomen. Otherwise, the belt can slip over the hips in the lap area in a frontal impact and injure the abdomen.
Adjusting the height ▷ To raise: pull. ▷ To lower: press the button, arrow 1, and push the head restraint down. Tilt Three different tilt positions are available. ▷ Forward: pull the top edge of the head re‐ straint forward, arrow 1. ▷ Back: press the button, arrow 2.
Adjusting the height ▷ To raise: pull. ▷ To lower: press the button, arrow 1, and push the head restraint down. The center head restraint cannot be adjusted in elevation. Folding down head restraints Extending/retracting head restraint Only fold down head restraint if no pas‐ sengers are in the rear.
3. Press the button. The LED in the button lights up. 4. Press the desired button 1 or 2. The LED goes out. If the M button is pressed accidentally: Press the button again.
Saving positions Seat and mirror memory, refer to page 53 Adjusting manually If an electrical malfunction occurs, for example, press the edges of the mirror glass. Automatic Curb Monitor When the reverse gear is engaged, the mirror glass tilts downward slightly on the front pas‐ senger side.
Functional requirement For proper operation: ▷ Keep the photocells clean. ▷ Do not cover the area between the inside rearview mirror and the windshield. Steering wheel General information Do not adjust while driving Do not adjust the steering wheel while driving; otherwise, an unexpected movement could result in an accident.
Transporting children safely Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g.
front, knee and side airbags on the front pas‐ senger side are deactivated. Deactivate the front passenger airbags auto‐ matically, refer to page 96 .
Mounts for the lower LATCH anchors The lower anchors may be used to attach the CRS to the vehicle seat up to a combined child and CRS weight of 65 lb/30 kg when the child is restr- ained by the internal harnesses.
Note Mounting eyes Only use the mounting eyes for the up‐ per retaining strap to secure child restraint fix‐ ing systems; otherwise, the mounting eyes could be damaged.
Driving Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
▷ While the driver's seat belt is unbuckled, if the driver's door is open and the low beams are switched off. When the ignition is switched off, by opening or closing the driver's door or unbuckling the driver's seat belt, the radio ready state remains active.
Engine stop Hints Take the remote control with you Take the remote control with you when leaving the vehicle so that children, for exam‐ ple, cannot start the engine.◀ Set the parking brake and further secure the vehicle as required Set the parking brake firmly when parking; oth‐ erwise, the vehicle could roll.
Displays in the instrument cluster The READY display in the tach‐ ometer signals that the Auto Start/Stop function is ready to start the engine automatically. The display indicates that the conditions for an automatic en‐ gine stop have not been satis‐ fied.
Activating/deactivating the system manually Using the button Press the button. ▷ LED comes on: Auto Start Stop function is deactivated. The engine is started during an automatic engine stop. The engine can only be stopped or started via the Start/Stop button.
periodically while coasting, if traffic conditions permit. The brake lamps will not light up if the parking brake is engaged. Turn signal, high beams, headlamp flasher Turn signal Do not fold in the e.
Switching on Press the wiper levers up. The lever automatically returns to its initial po‐ sition when released. ▷ Normal wiping speed: press up once. The wipers switch to intermittent operation when the vehicle is stationary. ▷ Fast wiping speed: press up twice or press once beyond the resistance point.
Setting the frequency or sensitivity of the rain sensor Turn the thumbwheel. Clean the windshield, headlamps Pull the wiper lever. The system sprays washer fluid on the wind‐ shield and activates the wipers briefly. In addition, the headlamps are cleaned at regu‐ lar intervals when the vehicle lights are switched on.
tainer. Use BMW’s Windshield Washer Con‐ centrate or the equivalent.◀ Washer fluid reservoir Adding washer fluid Only add washer fluid when the engine is cool, and then close the cover completely to avoid contact between the washer fluid and hot engine parts.
▷ With the ignition is off, if position N is en‐ gaged. ▷ If the safety belt is unbuckled, the driver's door is opened, and the brake pedal is not pressed while the vehicle is stationary and transmission position R or D is engaged. Before exiting the vehicle, make sure that posi‐ tion P of the automatic transmission is en‐ gaged.
The sport program of the transmission is acti‐ vated. Activating the M/S manual mode 1. Push the selector lever to the left out of transmission position D. 2. Push the selector lever forward or pull it backward. Manual mode becomes active and the gear is changed.
Hints Component wear Do not use Launch Control too often; otherwise, this may result in premature wear of components due to the high stress placed on the vehicle.◀ Did not use Launch Control during the break- in, refer to page 164 , period. To increase vehicle stability, activate DSC again as soon as possible.
Displays Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Overview, instrument cluster with enhanced features 1 Fuel gauge 78 2 Speedometer 3 Indicator/warning lamps 76 4 Tachometer 78 5 Engine oil temperature 78 6 Current fuel consumption 80 7 Electronic displays 75 8 Display/reset miles 79 Seite 74 Controls Displays 74 Online Edition for Part no.
Electronic displays Overview, instrument cluster 1 Messages, e.g. Check Control 76 Time 79 Date 79 External temperature 79 Selection lists 84 Service requirements 8.
Overview, instrument cluster with enhanced features 1 Time 79 External temperature 79 Date 79 Selection list, e.g., radio 84 Speed limit detection 82 Computer 84 Miles/trip miles 79 Navigation display, see user's manual for Navigation, Entertainment and Communi‐ cation.
Overview: indicator/warning lamps Symbol Function or system Turn signal. Front fog lamps. Rear fog lamp. High beams. High-beam Assistant. Parking lamps, headlamp control. Active Cruise Control. Vehicle detection, Active Cruise Control: collision warning.
Symbols Depending on the Check Control message, the following functions can be selected. ▷ "Owner's Manual" Display additional information about the Check Control message in the Integrated Owner's Manual. ▷ "Service request" Contact the service partner.
Coolant temperature If the coolant along with the engine becomes too hot, a Check Control message is displayed. Check the coolant level, refer to page 206 . Odometer and trip odometer ▷ Odometer, arrow 1. ▷ Trip odometer, arrow 2. Display/reset miles Press the knob.
Current fuel consumption Instrument cluster Displays the current fuel con‐ sumption. You can check whether you are currently driv‐ ing in an efficient and environ‐ mentally-friendly manner. Instrument cluster with enhanced features Displays the current fuel con‐ sumption.
Symbols Symbols Description No service is currently re‐ quired. The deadline for service or a legally mandated inspection is approaching. The service deadline has al‐ ready passed. Entering appointment dates Enter the dates for the required inspections.
Indicators to shift up or down are displayed in the instrument cluster. On vehicles without a gear shift indicator, the engaged gear is displayed. Manual transmission: displays Symbol Description Fuel efficient gear is engaged. Shift up to fuel efficient gear.
At a glance Camera The camera is located near the base of the mirror. Keep the windshield in the area behind the in‐ terior rear view mirror clean and clear.
Selection lists in the instrument cluster The concept The following can be displayed or operated us‐ ing the buttons and the thumbwheel on the steering wheel and the display in the instru‐ ment cluster: ▷ Current audio source. ▷ Redial on telephone.
Information at a glance Repeatedly pressing the button on the turn signal lever calls up the following information on the info display: ▷ Range. ▷ Average fuel consumption. ▷ Current fuel consumption. ▷ Average speed. ▷ Date. ▷ Speed limit detection.
The warning is repeated if the vehicle speed drops below the set speed limit once by at least 3 mph/5 km/h. Displaying, setting or changing the limit 1. "Settings" 2. "Speed" 3. "Warning at:" 4. Turn the controller until the desired limit is displayed.
Setting the time 1. "Settings" 2. "Time/Date" 3. "Time:" 4. Turn the controller until the desired hours are displayed. 5. Press the controller. 6. Turn the controller until the desired mi‐ nutes are displayed. 7. Press the controller.
Depending on the light conditions, the bright‐ ness control may not be clearly visible. Assist system information Display on the Control Display Information on the Assist system can be dis‐ played by activating Assist on the Control Dis‐ play. 1.
Lamps Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
3. "Pathway lighting:" 4. Set the duration. The setting is stored for the remote control currently in use. Automatic headlamp control Switch position : the low beams are switched on and off automatically, e.g., in tun‐ nels, in twilight or if there is precipitation.
To avoid blinding oncoming traffic, the Adap‐ tive Light Control does not swivel to the driv‐ er's side when the vehicle is at a standstill. When driving in reverse, only the turning lamp is active. Malfunction A Check Control message is displayed.
The system is not fully functional in situations such as the following, and driver intervention may be necessary: ▷ In very unfavorable weather conditions, such as fog or heavy precipitation.
To switch off permanently: press the button for approx. 3 seconds. Switch back on: press button. Reading lamps Press the button. Reading lamps are located at the front and rear next to the interior lamps. When the interior lamps are switched off per‐ manently, the reading lamps cannot be switched on.
Safety Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Protective action Airbags are not triggered in every impact situa‐ tion, e.g., in less severe accidents or rear-end collisions. Information on how to ensure the optimal protective effect of the airbags ▷ Keep at a distance from the airbags.
When there is a malfunction, have the airbag system checked immediately When there is a malfunction, have the airbag system checked immediately; otherwise, there is a risk that the system does not function as expected in the event of an accident despite corresponding severity of the accident.
Detected child seats The system generally detects children seated in a child seat, especially in the child seats that were required by NHTSA when the vehicle was manufactured. After installing a child seat, make sure that the indicator lamp for the front passenger airbags lights up.
All wheels green System is active and will issue a warning rela‐ tive to the tire inflation pressures stored during the last reset. One wheel is yellow A flat tire or major drop in inflation pressure in the indicated tire. All wheels are yellow A flat tire or major drop in inflation pressure in several tires.
If an identification is not possible, please contact the service center. 2. Rectify the flat tire. Use of tire sealant, e.g., the Mobility Sys‐ tem, may damage the TPM wheel elec‐ tronics. In this case, have the electronics checked at the next opportunity and have them replaced if necessary.
Malfunction The yellow warning lamp flashes and then lights up continuously. A Check Control message is displayed. No flat tire or loss of tire pressure can be detected. Display in the following situations: ▷ A wheel without TPM electronics is fitted: have the service center check it if neces‐ sary.
sured. Initialize the system after each correc‐ tion of the tire inflation pressure and after every tire or wheel change. Status display The current status of the Flat Tire Monitor can be displayed on the Control Display, e.g., whether or not the FTM is active.
If an identification is not possible, please contact the service center. 2. Rectify the flat tire. Run-flat tires Maximum speed You can continue driving with a damaged tire at speeds up to 50 mph/80 km/h. Continued driving with a flat tire If continuing to drive with a damaged tire: 1.
At a glance Button in the vehicle Intelligent Safety button Switching on/off The Intelligent Safety systems are automati‐ cally active after each engine start via the start/ stop button. Press the button: the systems are switched off. The LED goes out.
located within the detection range of the sys‐ tem. At a glance Button in the vehicle Intelligent Safety button Switching on/off Switching on automatically The system is automatically active every time the engine is started using the Start/Stop but‐ ton.
Detection range The system's detection capabilities are limited. This may result in the warning not being is‐ sued or being issued late. For example, the following situations may not be detected: ▷ Slow moving vehicles when you approach them at high speed.
At a glance Button in the vehicle Intelligent Safety button Switching on/off Switching on automatically The system is automatically active every time the engine is started using the Start/Stop but‐ ton. Switching off The system is only switched off until the next time the engine is started with the Start/Stop button.
Warning stages Symbol Measure The vehicle lights up red: prewarn‐ ing. Increase distance. The vehicle flashes red and an acoustic signal sounds: acute warn‐ ing.
It responds to persons that are within the de‐ tection range of the system. Detection range The warning area in front of the vehicle is div‐ ided into two areas. ▷ Central area, arrow 1, directly in front of the vehicle. ▷ Expanded area, arrow 2, to the right and left.
Intervene immediately by braking or making an evasive maneuver. Braking intervention The warning prompts the driver himself to in‐ tervene. During the warning, the maximum braking force is used, even with light pressure on the brake pedal. In addition, if there is a risk of collision, the system can assist with a slight braking intervention.
Notes Personal responsibility The system cannot serve as a substitute for the driver's personal judgment of the course of the road and the traffic situation. In the event of a warning, do not jerk the steer‐ ing wheel, as you may lose control of the vehi‐ cle.
▷ When the windshield in front of the interior rearview mirror is fogged over, dirty or cov‐ ered with stickers, etc. ▷ During calibration of the camera immedi‐ ately after vehicle shipment. Active Blind Spot Detection The concept Two radar sensors below the rear bumper monitor the area behind and next to the vehicle at speeds above approx.
Display Information stage The dimmed lamp in the mirror housing indi‐ cates when there are vehicles in the blind spot or approaching from behind. Warning If the turn signal is set while a vehicle is in the critical zone, the steering wheel vibrates briefly and the lamp in the mirror housing flashes brightly.
Attentiveness assistant The concept The system can detect increasing lack of alert‐ ness or fatigue of the driver during long, mo‐ notonous journeys, for example, on highways.
Note Personal responsibility The system cannot possibly serve as a substitute for the driver's personal judgment of the traffic situation. The system may not al‐ ways detect critical situations reliably and in a timely manner. Adapt speed to traffic situation and drive alertly; otherwise, a risk to safety may result.
Driving stability control systems Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e.
Indicator/warning lamps When DSC is deactivated, DSC OFF is dis‐ played in the instrument cluster. The indicator lamp lights up: DSC is deactivated. DTC Dynamic Traction Control The concept The DTC system is a version of the DSC in which forward momentum is optimized.
Variable sport steering The variable sport steering increases the steering angle of the front wheels at large steering wheel angles, e.g., in tight curves or when parking. Steering becomes more direct. It also varies the force required to turn the wheels in accordance with the vehicle speed.
Activating SPORT Press button repeatedly until SPORT is displayed in the instrument cluster. Configuring SPORT When the display is activated on the Control Display, refer to page 118 , the SPORT driving mode can be set to individual specifications. ▷ Activating SPORT.
Drive-off assistant This system supports driving away on gradi‐ ents. The parking brake is not required. 1. Hold the vehicle in place with the foot brake. 2. Release the foot brake and drive away without delay. After the foot brake is released, the vehicle is held in place for approx.
Driving comfort Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
The arrangement of the buttons varies accord‐ ing to the how the vehicle is equipped or coun‐ try-specific variants. Radar sensor A radar sensor is located in the front bumper for detecting vehicles on the road ahead of the vehicle. A dirty or covered sensor may hinder the de‐ tection of vehicles.
Press the rocker switch while the system is in‐ terrupted. When the system is switched on, the current speed is maintained and stored as the desired speed. It is displayed in the speedometer and briefly displayed in the instrument cluster, Displays in the instrument cluster, refer to page 123 .
The selected distance, refer to page 123 , is displayed in the instrument cluster. Calling up the desired speed and distance While driving Press the button with the system switched on. In the following cases, the stored speed value is deleted and cannot be called up again: ▷ When the system is switched off.
Distance display The system has been interrupted or distance control is deactivated be‐ cause the accelerator is being pressed; a vehicle was not detected. Distance control is deactivated be‐ cause the accelerator is being pressed; a vehicle was detected.
No warnings A warning may not be issued when ap‐ proaching a stationary or very slow-moving ob‐ stacle. You must react yourself; otherwise, there is the danger of an accident occurring.◀ Swerving vehicles A vehicle driving in front of you is not detected until it is completely within the same lane as your vehicle.
When approaching a curve, the system may react briefly to the vehicles in the next lane due to the bend of the curve. Any deceleration of the vehicle by the system can be compensated for by briefly accelerating. After the accelerator pedal is released, the system becomes active again and independently controls the speed.
Controls At a glance Press the button Function Interrupt system on/off Store speed Resume speed Changing the speed Switching on Press the button on the steering wheel. The marking in the speedometer is set to the current speed. Cruise control can be used.
Adapting the desired speed Adapt the desired speed to the road con‐ ditions and be ready to brake at all times; oth‐ erwise, there is the danger of an accident oc‐ curring.◀ Press the rocker switch up or down repeatedly until the desired speed is set.
▷ By the front middle sensors and the two corner sensors at approx. 24 in/60 cm. ▷ By the rear middle sensors at approx. 5 ft/1.50 m. Notes Check the traffic situation as well PDC cannot serve as a substitute for the driver's personal judgment of the traffic situa‐ tion.
If objects are located both in front of and be‐ hind the vehicle, an alternating continuous sig‐ nal is sounded. The intermittent tone is interrupted after ap‐ prox. 3 seconds: ▷ If the vehicle stops in front of an object that is detected by only one of the corner sen‐ sors.
The range of the sensors is shown as a shaded area on the Control Display. PDC has failed. Have the system checked. To ensure full operability: ▷ Keep the sensors clean and free of ice. ▷ When using high-pressure washers, do not spray the sensors for long periods and maintain a distance of at least 12 in/30 cm.
Switching on/off manually Press the button. ▷ On: the LED lights up. ▷ Off: the LED goes out. The PDC is shown on the Control Display. Switching on the rearview camera via the iDrive With PDC activated or Top View switched on: "Rear view camera" The rearview camera image is displayed.
Obstacle marking General information ▷ Spatially-shaped markings can be shown in the rearview camera image. Their colored steps match the markings of the PDC. This simplifies estimation of the distance to the object shown. Parking using pathway and turning circle lines 1.
visibility, two cameras in the front of the vehi‐ cle record the traffic situation on each side. Notes The images from both cameras are shown si‐ multaneously on the Control Display. Check the traffic situation as well Check the traffic situation around the ve‐ hicle on blind driveways and intersections with your own eyes.
System limits The cameras capture a maximum range of 330 ft/100 m. Top View The concept Top View assists you in parking and maneu‐ vering. The area around the doors and the road area around the vehicle are shown on the Con‐ trol Display for this purpose.
Switching on the backup camera via the iDrive With Top View switched on: "Rear view camera" The backup camera image is displayed. The setting is stored for the remote control cur‐ rently in use. Display Visual warning The approach of the vehicle to an object can be shown on the Control Display.
Parking assistant The concept This system assists the driver in parking paral‐ lel to the road. Ultrasound sensors measure parking spaces on both sides of the vehicle. The parking assistant calculates the best pos‐ sible parking line and takes control of steering during the parking procedure.
At a glance Button in the vehicle Parking assistant Ultrasound sensors The ultrasound sensors for measuring parking spaces are located on the wheel arches.
The parking procedure is active. Steering control has been seized. Status of the parking space search ▷ Gray, arrow 1: parking space search. ▷ Blue, arrow 2: parking space is suitable. The vehicle is parked in the parking space if the parking procedure is active.
Interrupting automatically The system is interrupted automatically in the following situations: ▷ If the driver grasps the steering wheel or if he takes over steering. ▷ If a gear is selected that does not match the instruction on the Control Display.
Head-up Display The concept This system projects important information into the driver's field of vision, e.g., the speed. In this way, the driver can get information with‐ out averting his or her eyes from the road. Display visibility The visibility of the displays in the Head-up Display is influenced by: ▷ Certain sitting positions.
Setting the rotation 1. "Settings" 2. "Head-Up Display" 3. "Rotation" 4. Turn the controller. The setting is stored for the remote control currently in use. Special windshield The windshield is part of the system. The shape of the windshield makes it possible to display a precise image.
Climate control Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Climate control functions in detail Manual air distribution Turn the wheel to select the de‐ sired program or the desired in‐ termediate setting. ▷ Windows.
▷ LED off: outside air flows in continuously. ▷ LED on, recirculated-air mode: the supply of outside air into the vehicle is perma‐ nently blocked. If the windows fog over, switch off recircu‐ lated-air mode and increase the air volume, if necessary.
5 Maximum cooling 6 Temperature, right 7 Seat heating, right 50 8 Cooling function 9 Automatic recirculated-air control/recircu‐ lated-air mode 10 Air distribution, right 11 Air flow, AUTO int.
The cooling function is switched on automati‐ cally with the AUTO program. When using the automatic climate control, condensation water, refer to page 166 , devel‐ ops that exits underneath the vehicle.
Switching on Press any button except ▷ Rear window defroster. ▷ Seat heating. Microfilter/activated-charcoal filter In external and recirculated air mode the mi‐ crofilter/activated charcoal filter filters dust, pollen, and gaseous pollutants out of the air.
Preselecting the switch-on time 1. "Settings" 2. "Climate" 3. "Timer 1:" or "Timer 2:" 4. Set the desired time.
Interior equipment Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
erases all programming of the buttons on the interior rearview mirror. 3. Hold the hand-held transmitter for the sys‐ tem to be controlled approx. 1 to 3 in/2.5 to 8 cm away from the buttons on the interior rearview mirror. The required distance de‐ pends on the manual transmitter.
4. Likewise, press and hold the button of the desired function on the hand-held trans‐ mitter. 5. Release both buttons as soon as the inte‐ rior rearview mirror LED flashes more rap‐ idly. When the LED is flashing faster, this indicates that the button on the interior rearview mirror has been programmed.
World map with magnetic zones Procedure 1. Press and hold the control button for ap‐ prox. 3 to 4 seconds. The number of the set compass zone appears in the mirror. 2. To change the zone setting, press the con‐ trol button quickly and repeatedly until the number of the compass zone correspond‐ ing to your location appears in the mirror.
The setting is stored automatically after ap‐ proximately 10 seconds. Ashtray/cigarette lighter Ashtray Opening Raise cover. Emptying Take out the insert. Lighter Danger of burns Only hold the hot lighter by its knob; oth‐ erwise, there is the danger of getting burned.
Front center console Raise the cap and remove the cover or ciga‐ rette lighter. In the front passenger footwell The socket is located below the glove com‐ partment. Rear center console Remove the cover. In the cargo area The socket is located on the left side in the cargo area.
With Professional navigation system or TV: at a glance The USB interface is located in the center arm‐ rest. Notes Observe the following when connecting: ▷ Do not use force when plugging the con‐ nector into the USB interface. ▷ Do not connect devices such as fans or lamps to the USB interface.
3. Push the corresponding head restraint down as far as it will go. 4. Pull the corresponding lever in the cargo area to release the rear seat backrest. 5. The unlocked rear seat backrest moves forward slightly. 6. Fold backrest forward. Closing 1. Return the rear seat backrest to the upright seating position and engage it.
Storage compartments Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Locking The glove compartment can be locked with an integrated key to separately secure the trunk lid, refer to page 39 , for example. This prevents access to the glove compart‐ ment and to the cargo area. After the glove compartment is locked, the re‐ mote control can be handed over, such as at a hotel, without the integrated key.
Connection for an external audio device . Description, see user's manual for Navigation, Entertainment and Communication. Storage compartment in the rear Storage compartment is located in the rear center console. Cupholders Hints Shatter-proof containers and no hot drinks Use light and shatter-proof containers and do not transport hot drinks.
No heavy objects Do not hang heavy objects from the hooks; otherwise, they may present a danger to passengers during braking and evasive ma‐ neuvers.◀ Storage compartments in the cargo area Storage compartment A storage compartment is located on the left side.
Online Edition for Part no. 01 40 2 911 066 - VI/13.
Driving tips This chapter provides you with information useful in dealing with specific driving and operating modes. Online Edition for Part no. 01 40 2 911 066 - VI/13.
Things to remember when driving Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e.
Hot exhaust system Hot exhaust system High temperatures are generated in the exhaust system. Do not remove the heat shields installed and never apply undercoating to them.
Objects in the area around the pedals No objects in the area around the pedals Keep floor mats, carpets, and any other objects out of the area of motion of the pedals; otherwise, the function of the pedals could be impeded while driving Do not place additional floor mats over existing mats or other objects.
Loading Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Stowing cargo ▷ Cover sharp edges and corners on the cargo. ▷ Heavy cargo: stow as far forward as possi‐ ble, directly behind and at the bottom of the rear passenger seat backrests. ▷ Very heavy cargo: when the rear seat is not occupied, secure each of the outer safety belts in the opposite buckle.
Roof drip rail with flaps The anchorage points are located in the roof drip rail above the doors. Fold the cover outward. Loading Be sure that adequate clearance is maintained for tilting and opening the glass sunroof.
Saving fuel Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Avoid high engine speeds Use 1st gear to get the vehicle in motion. Be‐ ginning with 2nd gear, accelerate rapidly. When accelerating, shift up before reaching high engine speeds. When you reach the desired speed, shift into the highest applicable gear and drive with the engine speed as low as possible and at a con‐ stant speed.
▷ ECO PRO bonus range, refer to page 172 . ▷ ECO PRO tips driving instruction, refer to page 173 ▷ ECO PRO climate control, refer to page 172 . Activating ECO PRO Press button repeatedly until ECO PRO is displayed in the instrument cluster. Configuring ECO PRO Via the Driving Dynamics Control 1.
Mark in the POWER area, arrow 2: display when accelerating. The efficiency of the driving style is shown by the color of the bar: ▷ Blue display: efficient driving style as long as the mark moves within the blue range. ▷ Gray display: adjust driving style, e.
▷ Energy recovery. ▷ Climate control output. ▷ Coasting. Display ECO PRO tips "ECO PRO Tips" The setting is stored for the profile currently in use.
Color code blue, arrow 1, and symbol, arrow 2: driving condition Coasting. Displaying EfficientDynamics info 1. "Vehicle Info" 2. "EfficientDynamics" 3. "EfficientDynamics info" Deactivating the system manually The function can be deactivated in the Config‐ ure ECO PRO, refer to page 172 , menu, e.
Online Edition for Part no. 01 40 2 911 066 - VI/13.
Mobility In order to always ensure your mobility, you will find important information on operating fluids, wheels and tires, maintenance and Roadside Assistance in the following.
Refueling Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
1. Open the cover on the right side trim. To do this, turn the cap. 2. Pull the green knob with the fuel pump symbol. This releases the fuel filler flap. Observe the following when refueling The fuel tank is full when the filler nozzle clicks off the first time.
Fuel Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Use only Ultra-Low Sulfur Diesel. The fraction of biodiesel in the fuel must not exceed 5 %, referred to as B5. Do not use gasoline. If you do fill the tank with the wrong fuel, e.g., gasoline, do not start the engine as this may damage the engine.◀ After adding the wrong fuel, contact your serv‐ ice center or roadside assistance.
Refill in good time The reducing agent must be replenished as soon as the Reserve display appears, other‐ wise the engine cannot be restarted.◀ Diesel exhaust fluid on minimum The engine will cont.
Refill quantity Refill quantity when the Reserve display first appears: Max. 3 gallons/11.3 liters Tank for reducing agent The tank for the reducing agent is located next to the fuel tank. Adding engine oil 1. Open the fuel filler flap, refer to page 178 .
Reserve indication The Reserve indication will still appear when the engine is started after refilling. After sev‐ eral minutes of driving, the Re‐ serve indication goes out.
Wheels and tires Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Tire inflation pressure values up to 100 mph/160 km/h 320i Tire size Pressure specifica‐ tions in bar/PSI Specifications in bar/PSI with cold tires 225/50 R 17 94 V M +S A/S RSC 225/50 R 17 94 H M +S RSC 2.2 / 32 2.2 / 32 225/45 R 18 91 V M +S A/S RSC 225/45 R 18 91 Y RSC 225/45 R 18 95 V M +S XL RSC 2.
Tire size Pressure specifica‐ tions in bar/PSI Front: 225/40 R 19 89 Y RSC Rear: 255/35 R 19 92 Y RSC 2.2 / 32 - - 2.4 / 35 Front: 225/35 R 20 90 Y XL RSC Rear: 255/30 R 20 92 Y XL RSC 2.5 / 36 - - 3.0 / 44 Compact wheel T 135/80 R 17 102 M Speed up to a max.
Tire size Pressure specifica‐ tions in bar/PSI Front: 225/45 R 18 91 Y RSC Rear: 255/40 R 18 95 Y RSC 2.2 / 32 - - 2.4 / 35 Front: 225/40 R 19 89 Y RSC Rear: 255/35 R 19 92 Y RSC 2.4 / 35 - - 2.6 / 38 Front: 225/35 R 20 90 Y XL RSC Rear: 255/30 R 20 92 Y XL RSC 2.
Tire inflation pressure values over 100 mph/160 km/h 320i, 320i xDrive Without high-speed tuning feature Tire size Pressure specifica‐ tions in bar/PSI Specifications in bar/PSI with cold tires 225/50 R 17 94 V M +S A/S RSC 225/50 R 17 94 H M +S RSC 2.
With high-speed tuning feature Tire size Pressure specifica‐ tions in bar/PSI Specifications in bar/PSI with cold tires 225/50 R 17 94 V M +S A/S RSC 225/50 R 17 94 H M +S RSC 2.2 / 32 2.7 / 39 225/45 R 18 91 Y RSC 225/45 R 18 95 V M +S XL RSC 2.4 / 35 2.
Tire size Pressure specifica‐ tions in bar/PSI Front: 225/50 R 17 94 W RSC Rear: 255/45 R 17 98 W RSC 2.4 / 35 - - 2.6 / 38 Front: 225/45 R 18 91 Y RSC Rear: 255/40 R 18 95 Y RSC 2.6 / 38 - - 2.6 / 38 Front: 225/40 R 19 89 Y RSC Rear: 255/35 R 19 92 Y RSC 2.
Tire size Pressure specifica‐ tions in bar/PSI 225/45 R 18 91 V M +S A/S RSC 225/45 R 18 91 Y RSC 225/45 R 18 95 V M +S XL RSC 2.6 / 38 3.1 / 45 Front: 225/50 R 17 94 W RSC Rear: 255/45 R 17 98 W RSC 2.4 / 35 - - 2.6 / 38 Front: 225/45 R 18 91 Y RSC Rear: 255/40 R 18 95 Y RSC 2.
Tire size Pressure specifica‐ tions in bar/PSI Specifications in bar/PSI with cold tires 225/45 R 18 91 V M +S A/S RSC 225/45 R 18 91 Y RSC 225/50 R 17 94 H M +S RSC 225/45 R 18 95 V M +S XL RSC 2.7 / 39 3.2 / 46 Front: 225/45 R 18 91 Y RSC Rear: 255/40 R 18 95 Y RSC 2.
Tire size Pressure specifica‐ tions in bar/PSI Specifications in bar/PSI with cold tires 225/45 R 18 91 V M +S A/S RSC 225/45 R 18 91 Y RSC 225/50 R 17 94 H M +S RSC 225/45 R 18 95 V M +S XL RSC 2.7 / 39 3.2 / 46 Front: 225/45 R 18 91 Y RSC Rear: 255/40 R 18 95 Y RSC 2.
Tire size Pressure specifica‐ tions in bar/PSI Specifications in bar/PSI with cold tires 225/50 R 17 94 V M +S A/S RSC 225/50 R 17 94 H M +S RSC 2.4 / 35 2.9 /42 225/45 R 18 91 V M +S A/S RSC 225/45 R 18 91 Y RSC 225/45 R 18 95 V M +S XL RSC 2.6 / 38 3.
Tire identification marks Tire size 245/45 R 18 96 Y 245: nominal width in mm 45: aspect ratio in % R: radial tire code 18: rim diameter in inches 96: load rating, not for ZR tires Y: speed rating, be.
sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades Band A represent higher levels of performance on the laboratory test wheel than the minimum re‐ quired by law.
In case of tire damage If there are indications of tire damage, re‐ duce your speed immediately and have the wheels and tires checked right away; other‐ wise, there is the increased risk of an accident. Drive carefully to the nearest service center.
Retreaded tires Possibly substantial variations in the de‐ sign and age of the tire casing structures can limit service life and have a negative impact on road safety.◀ Winter tires The manufacturer of your vehicle recommends winter tires for winter roads or at temperatures below +45 ℉/+7 ℃.
Consult your service center for more informa‐ tion. Use Use only in pairs on the rear wheels, equipped with the tires of the following size: ▷ 205/60 R 16. ▷ 225/55 R 16. ▷ 225/50 R 17. ▷ 225/45 R 18. Follow the chain manufacturer's instructions.
Engine compartment Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Hood Hints Working in the engine compartment Never attempt to perform any service or repair operations on your vehicle without the necessary professional technical training. If you are unfamiliar with the statutory guide‐ lines, have any work on the vehicle performed only by a service center.
Engine oil Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Performing a detailed measurement In order to perform a detailed measurement of the engine oil level: 1. "Vehicle Info" 2. "Vehicle status" 3. "Measure engine oil level" 4. "Start measurement" The oil level is checked and displayed via a scale.
Diesel engine API ILSAC GF-5. Oil change An oil change should be carried out by your service center only. Seite 205 Engine oil Mobility 205 Online Edition for Part no.
Coolant Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Maintenance Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Socket for OBD Onboard Diagnosis Position There is an OBD socket on the driver's side for checking the primary components in the vehi‐ cle emissions. Emissions ▷ The warning lamp lights up: Emissions are deteriorating. Have the vehicle checked as soon as possible.
Replacing components Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Danger of burns Only change bulbs when they are cool; otherwise, there is the danger of getting burned.◀ Working on the lighting system When working on the lighting system, you should always switch off the lights af‐ fected to prevent short circuits.
Accessing the turn signals and low beams Follow the general instructions on lamps and bulbs, refer to page 209 . 1. In the wheel house, loosen the two brack‐ ets and remove the cover. Turn signal 21-watt bulb, PY21W 1. If necessary, pull the inside trim of the wheel house slightly inward.
Accessing the daytime running lights, high beams/headlamp flasher and parking lamps Follow the general instructions on lamps and bulbs, refer to page 209 . 1. Open the hood, refer to page 202 . 2. Turn the cap counterclockwise and re‐ move. Parking lamps 6-watt bulb, H6W.
Daytime running lights 24-watt bulb, PW24W. 1. If necessary, remove the high beam bulb connector. 2. Remove the bulb holder. 3. Remove the bulb from the bulb holder. 4. To insert the new bulb, proceed in reverse order of removal. During insertion, the bot‐ tom of the bulb holder must be facing downward.
21-watt bulb, PY21W 1. In the wheel house, loosen the two brack‐ ets and remove the cover. 2. If necessary, pull the inside trim of the wheel house slightly inward. Turn the bulb holder counterclockwise and remove. 3. Press the bulb gently into the socket, turn counterclockwise and remove.
Tail lamps, bulb replacement At a glance 1 Turn signal 2 Reversing lamp 3 Inside brake lamp 4 Tail lamps 5 Outside brake lamp Bulb replacement, exterior tail lamps General information Follow the general instructions on lamps and bulbs, refer to page 209 .
5. Remove the connecting line from the clip on the bulb holder. 6. Release the catch at the top on the con‐ nector of the connecting line and remove the connector from the bulb holder. Replacing the bulbs 1. Loosen the four fasteners, arrow 1, on the bulb holder and remove the bulb holder from the tail lamp, arrow 2.
Replacing the reversing lamp and inner brake lamp 1. Loosen the two fasteners, arrow 1 and pull down on the lamp holder to remove, ar‐ row 2. 2. Press the defective bulb gently into the socket, turn counterclockwise and remove. 3. Insert the new bulb.
ter to ensure that all comfort functions are fully available and that any Check Control mes‐ sages of these comfort functions are no longer displayed. Charging the battery Note Do not plug chargers into the socket Do not connect battery chargers to the factory-installed sockets in the vehicle as this may damage the battery.
3. Remove the cover from one side, arrow 3. 4. Press the four fasteners and remove the cover. Attaching the covers 1. When attaching the cover, make sure that all four fasteners are engaged. 2. Attach the cover under the rubber lip and then thread it between the bars.
Breakdown assistance Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
if it can be established, are transmitted to the BMW Response Center. ▷ If the LED is flashing, but the BMW Re‐ sponse Center can no longer be heard via the speaker, you can nevertheless still be heard for the BMW Response Center.
Preparation 1. Check whether the battery of the other ve‐ hicle has a voltage of 12 volts. This infor‐ mation can be found on the battery. 2. Switch off the engine of the assisting vehi‐ cle. 3. Switch off any electronic systems/power consumers in both vehicles.
If the first starting attempt is not success‐ ful, wait a few minutes before making an‐ other attempt in order to allow the dis‐ charged battery to recharge. 3. Let both engines run for several minutes. 4. Disconnect the jumper cables in the re‐ verse order.
Tow truck Have your vehicle transported with a tow truck with a so-called lift bar or on a flat bed. Do not lift the vehicle Do not lift the vehicle by the tow fitting or body and chassis parts; otherwise, damage may result.
▷ Avoid lateral loading of the tow fitting, e.g., do not lift the vehicle by the tow fitting. Otherwise, damage to the tow fitting and the vehicle can occur.◀ Screw thread Push out the cover by pressing on the top edge. Tow-starting Automatic transmission Do not tow-start the vehicle.
Care Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Automatic transmission: 1. Drive into the car wash. 2. Engage transmission position N. 3. Switch the engine off. In this way, the ignition remains switched on, and a Check-Control message is dis‐ played.
To guard against discoloration, such as from clothing, provide leather care roughly every two months. Clean light-colored leather more frequently be‐ cause soiling on such surfaces is substantially more visible. Use leather care products; otherwise, dirt and grease will gradually break down the protective layer of the leather surface.
Use only a mild soapy solution, with the safety belts clipped into their buckles. Do not allow the reels to retract the safety belts until they are dry.
Online Edition for Part no. 01 40 2 911 066 - VI/13.
Reference This chapter contains the technical data and an index that will quickly take you to the information you need. Online Edition for Part no. 01 40 2 911 066 - VI/13.
Technical data Vehicle equipment All standard, country-specific and optional equipment that is offered in the model series is described in this chapter. Therefore, equip‐ ment is also described that is not available in a vehicle, e. g., because of the selected optional equipment or country variant.
Length, wheel base 1 Wheel base: 110.6 inches/2,810 mm 2 Vehicle length: 182.1 inches/4,627 mm Smallest turning circle Dia.: 37 ft/11.3 m Dia. with xDrive: 38 ft/11.7 m Weights The values preceding the slash apply to vehi‐ cles with manual transmission; the values fol‐ lowing the slash apply to vehicles with auto‐ matic transmission.
328i Approved gross vehicle weight lbs kg 4,365/4,420 1,980/2,005 Load lbs/kg 900/408 Approved front axle load lbs/kg 2,015/914 Approved rear axle load lbs/kg 2,510/1,139 Approved roof load capacity lbs/kg 165/75 Trunk capacity cu ft/l 16.
328i xDrive Approved gross vehicle weight lbs/kg 4,585/2,080 Load lbs/kg 900/408 Approved front axle load lbs/kg 2,170/984 Approved rear axle load lbs/kg 2,555/1,159 Approved roof load capacity lbs/kg 165/75 Cargo area capacity cu ft/l 16.
328d xDrive Approved rear axle load lbs/kg 2,525/1,145 Approved roof load capacity lbs/kg 165/75 Cargo area capacity cu ft/l 16.9/480 Capacities US gal/liters Notes Fuel tank Gasoline: 15.8/60 Diesel: 15/57 Fuel quality, refer to page 180 Windshield and headlamp washer system 0.
Seite 237 Technical data Reference 237 Online Edition for Part no. 01 40 2 911 066 - VI/13.
Everything from A to Z Index A ABS, Antilock Brake Sys‐ tem 115 ACC, Active Cruise Control with Stop & Go 120 Acceleration Assistant, refer to Launch Control 71 Activated-charcoal filter 148 Act.
BMW maintenance sys‐ tem 207 Bonus range, ECO PRO 172 Bottle holder, refer to Cu‐ pholder 160 Brake assistant 115 Brake discs, breaking in 164 Brake force display 112 Brake lamps, brake force dis.
ConnectedDrive Services Connecting electrical devi‐ ces 154 Control Display 16 Control Display, settings 86 Controller 16 , 17 Control systems, driving sta‐ bility 115 Convenient opening 36 Coolan.
Engine oil, adding 204 Engine oil additives 204 Engine oil change 205 Engine oil filler neck 204 Engine oil temperature 78 Engine oil types, alterna‐ tive 204 Engine oil types, ap‐ proved 204 Engi.
High beams/low beams, refer to High-beam Assistant 91 Hills 166 Hill start assistant, refer to Drive-off assistant 119 Hints 6 Holder for beverages 160 Homepage 6 Hood 202 Horn 12 Hotel function, trun.
Low beams 89 Low beams, automatic, refer to High-beam Assistant 91 Lower back support 49 Low-Sulfur Diesel 180 Luggage rack, refer to Roof- mounted luggage rack 168 Lumbar support 49 M Maintenance 207.
P Paint, vehicle 227 Parallel parking assistant 137 Park Distance Control PDC 128 Parked-car ventilation 148 Parked vehicle, condensa‐ tion 166 Parking aid, refer to PDC 128 Parking assistant 137 Pa.
Service requirements, dis‐ play 80 Service, Roadside Assis‐ tance 221 Services, ConnectedDrive Settings, locking/unlock‐ ing 41 Settings on Control Dis‐ play 86 Settings, storing for seat, mir.
Total vehicle weight 233 Touchpad 19 Tow fitting 224 Towing 223 Tow-starting 223 Tow truck 224 TPM Tire Pressure Moni‐ tor 97 Traction control 116 TRACTION program, Dy‐ namic Driving Control 116 T.
.
More about BMW bmwusa.com The Ultimate Driving Machine 01 40 2 911 066 ue *BL291106600P* Online Edition for Part no. 01 40 2 911 066 - VI/13.
デバイスBMW 320i xDrive Sedan (2014)の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
BMW 320i xDrive Sedan (2014)をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBMW 320i xDrive Sedan (2014)の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。BMW 320i xDrive Sedan (2014)の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。BMW 320i xDrive Sedan (2014)で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
BMW 320i xDrive Sedan (2014)を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBMW 320i xDrive Sedan (2014)の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、BMW 320i xDrive Sedan (2014)に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBMW 320i xDrive Sedan (2014)デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
