Bolensメーカー350Eの使用説明書/サービス説明書
ページ先へ移動 of 20
Front Tine Tiller Model Series 300 & 33 0 OPERA T OR’S MANU AL IMPOR T ANT : READ SAFETY RULES AND INSTRUCTIONS CAREF ULL Y MTD LLC, P .O . BO X 3611 31 CLEVELAND , OHIO 44136-001 9 Warning: Thi.
2 TABLE OF CONTENTS Cont ent P age Important Safe O peratio n Prac tices ................. ............. ............. ............. ........... 3 Assembl ing Your Till er .................. ................... ............. ............. ............
3 SECTION 1: IMPORTANT SAFE OPERATION PR ACTICES WARNING: This sy mbol points out impo rtant safety instruc tions whi ch, if not foll owed, co uld endange r the personal safety and/o r proper ty of yourse lf and other s. Read an d follow all in struct ions in this manual before attempt i ng to oper ate this mac hine.
4 9. Look down and behind and use c are when in reverse or pulling mac hine towards you. 10. Start the engine according to the instructions found in this manual and keep feet well away from the tines at all times. 11. After striking a foreign object, stop the engine, disconnect the spark plug wi re and ground against the engine.
5 SECTION 2: ASSEMBLING YOUR TILLER NOTE: This operat or’s m anual cover s var ious m odels of tillers. The units il lustrat ed may var y slight ly from your uni t.
6 Check Cable Ad justment • With the clut ch lever disengage d, pull star ter rope slowly sev eral time s. The tine s should no t turn. If they tur n, th e cable is not adj usted properly . • To adjust the cable, loos en the nut near the top of the cable an d unscre w the cabl e to provid e additiona l s lack in wire .
7 Choke Lever The choke le ver i s located ne ar the thr ottle cont rol. It is used to enr ich the fuel mix ture when sta rting a cold engine . Starte r Handle The sta rter han dle is l ocated on the e ngine and is used to m anuall y star t the eng ine.
8 Controlling Speed And Tilling Depth Wheel Yoke Adjustment Place whe el yoke so that the wheel s are forw ard (nearest po int betwee n wheels and tines) for sha llow tilling , cultivat ing and trans port. Th e forward spee d will increa se. Turn yoke arou nd (farthe st point between wheels and tines) for deep tilling.
9 wor king wid th of t he m achi ne is 22 o r 24 i nches . Fo r cultiv ation, this may be re duced to 13 inc hes by removi ng the outer tines . Refer to the Adj ustment Sec tion. When layin g out pla nt rows, be sure t o allow enough width to permit cu ltivatio n between th e rows.
10 SECTION 6: MAINTAINI NG YOUR TILLER WARNING: Disconnect the spark plug wire and ground it against the en gine before per forming any repairs or maintenance. Engine Refer to the se parate engi ne manua l for engin e maintenan ce i nstr uctions. Maintain engine oil as i nstru cted i n the sepa rate engine m anual packe d with your unit.
11 Fig ure 12 Off-Season Storage If the tiller wil l not be used for a period lo nger than 30 days, the following steps should be taken t o prepar e the tiller for s torage. • Clean t he exter ior o f engine and the e ntire ti ller thorough ly. L ubricat e the ti ller as d escrib ed in t he lubric ation in structi ons.
12 SECTION 7: TROUBLESHOOTING NOTE: For repair s bey ond th e minor adjus tments l isted a bove, c ontact y our ne arest s ervice deale r. Problem Cau se Rem edy Engine fail s to s tart 1. Spark p lug wi re dis connec ted. 2. Fuel tank emp ty or stale fuel .
13 SECTION 8: NOTES.
14 Model Series 300 & 330 1 2 3 4 5 6 7 8 5 6 9 10 11 12 13 5 14 14 15 16 17 18 19 20 21 22 23 24 14 10 9 10 25 10 26 27 28 29 30 31 32 33 34 35 36 37 38 39 34 40 41 42 43 44 45 46 47 48 49 50 51 .
15 Model Series 300 & 330 Ref . No. P art No. P ar t Description 1. 720-0 274 Gri p 2. 731-0 473 Clut ch Gr ip 3. 686-0 002 Clut ch L ev er 4. 649- 0137 Handl e Assemb ly 5. 712- 0442 Lock Nut Cap 1/4 -20 6. 738-122 5 Sh oul der Scre w 7. 74 6-1 148 Clut ch Cab le 8.
16 Model Series 300 1 2 3 1 2 4 5 6 7 8 9 10 11 6 12 13 14 15 16 20 17 4 15 16 18 18 10 19.
17 Model Series 300 Ref . No. P art No. P ar t Description 1. 734- 1988 Wheel 7 x 1.8 2. 738-092 9 Shoulder Scre w 3. 686-008 1A Wheel Bra cket Ass embly 4. 71 4-0 149 B Cot ter Pi n 5. 71 1-0415 Clev is Pin 6. 736-024 2 Bell W asher .340 ID x .872 OD 7.
18 Model Series 330 1 3 1 2 2 4 9 5 6 7 8 10 10 11 13 14 6 12 15 16 4 5 17 18 19.
19 Model Series 330 Ref . No. P art No. P ar t Description 1. 734- 1781 Wheel 8 x 1.75 2. 738-092 9 Shoulder Scre w 3. 686-008 1A Wheel Bra cket Ass embly 4. 71 4-0 149 B Cot ter Pi n 5. 71 1-0415 Clev is Pin 6. 736-024 2 Bell W asher .340 ID x .872 OD 7.
MANUF ACTURER’S LIMITED W ARRAN TY FOR: The limi ted warra nty set forth below is given b y MTD LLC with respe ct to new m erchandise purchased an d used in the United S tates , its possessio ns and te rritories.
デバイスBolens 350Eの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bolens 350Eをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBolens 350Eの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bolens 350Eの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bolens 350Eで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bolens 350Eを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBolens 350Eの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bolens 350Eに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBolens 350Eデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。