Bosch Appliancesメーカー5000 PTZの使用説明書/サービス説明書
ページ先へ移動 of 22
AUTODOME 5000 PTZ Camera en Installation Guide.
.
Table of contents 1 Safety 4 1.1 About this Manual 4 1.2 Conventions in this Manual 4 1.3 Legal Information 4 1.4 Important Safety Instructions 4 2 Description 6 2.1 Unpacking 6 3 Installing a Recessed Mount 7 3.1 Parts List 7 3.2 Installing the Recessed Mount 8 4 Installing a Pipe Mount 10 4.
Safety About this Manual This manual has been compiled with great care and the information it contains has been thoroughly verified. The text was complete and correct at the time of printing. Because of the ongoing development of products, the content of the manual may change without notice.
– Only use accessories that have been recommended by the manufacturer or are delivered with the device. – Fit the device according to the manufacturer's instructions.
Description This manual provides instructions for mounting a AUTODOME 5000 Series PTZ Dome to the VEZ-A5-IC In-ceiling (Recessed) Mount. This mount allows you to recess the AUTODOME 5000 into an indoor drop-ceiling. This manual provides instructions for mounting a AUTODOME 5000 PTZ Dome to the VEZ-A5- PP Pipe Mount.
Installing a Recessed Mount Use this chapter to install the indoor dome camera into an indoor ceiling space. Parts List Quantity Item 1 Ceiling Bracket 1 Rubber Gasket 1 Housing Frame 1 Trim Ring 3 M4x10 Phillips Screws 1 Guide Pattern 1 Installation Manual 3 3.
Installing the Recessed Mount The illustration below shows the required parts for the recessed mount. Refer to the steps that follow for instructions. 1 2 3 4 5 6 1 Ceiling Bracket 4 Housing Frame 2 M4x10 Screws (3 pieces) 5 Dome Camera 3 Rubber Gasket 6 Trim Ring 3.
Recessed Mount Installation Instructions 1. Find a secure location on the ceiling and apply the ceiling guide pattern the ceiling tile or drywall. Use the pattern as a template to cut the proper circle in the ceiling.
Installing a Pipe Mount Use this chapter to install and indoor or outdoor dome camera to a pipe. Parts List Quantity Item 1 Pipe Mount Base with Safety Tether 1 300 mm (11.81 in.) Pipe Extension 1 200 mm (7.87 in.) Pipe Extension 1 M38 to M38 Connection Ring 1 M38 to M33 Connection Ring 1 3/4 x 260 in.
Installing the Pipe Mount The illustration below shows the required parts for the pipe mount. Refer to the steps that follow for instructions. 1 2 3 4 6 5 9 8 7 1 Pipe Mount Base 6 M38 to M33 Pipe Connector 2 M10x25L Phillips Screws (4 pieces) 7 Safety Tether 3 Pipe Extension, 300 mm (11.
Pipe Mount Installation Instructions ! Caution! Strength of Mounting Surface The fasteners and mounting surface must be capable of supporting a maximum load of 12 kg (26.4 pounds). 1. Locate a secure position to secure the Pipe Mount Base (1). Ensure there is an adequate opening in the ceiling or mounting structure for the wires to pass through.
14. Place the top of the Dome Camera (9) inside the Adaptor (8) and turn clockwise until the Dome Camera latches to the Adaptor. 15. Fasten the M5x8L screw using the T20 Security Torx wrench (shipped with the camera) to secure the Dome Camera to the Adaptor.
Installing a Wall Mount Use this chapter to install and indoor or outdoor dome camera to a wall. Parts List Quantity Item 1 Wall Mount with Safety Tether 1 3/4 x 260 in. Roll Teflon Tape 1 5g Container Silicon Grease 4 M10x25L Phillips Screws 1 Rubber Gasket 1 Installation Manual 5 5.
Installing the Wall Mount The illustration below shows the required parts for the wall mount. Refer to the steps that follow for instructions. 1 Wall Mount Base 4 Safety Tether 2 Washers (4 pieces) 5 Adaptor 3 M10x25L Phillips Screws (4 pieces) 6 Dome Camera 5.
Wall Mount Installation Instructions ! Caution! Strength of Mounting Surface The fasteners and mounting surface must be capable of supporting a maximum load of 12 kg (26.4 pounds). 1. Locate a secure position to secure the Wall Mount Base (1). Ensure there is an adequate opening in the wall for the wires to pass through.
Replacing the Bubble This section provides instructions for replacing a bubble on an AUTODOME 5000 camera. Parts List Quantity Item 1 Tinted Bubble with Trim Ring (with two (2) M3x23L Torx screws attached) 1 Torx Wrench 1 Installation Manual 6 6.1 AUTODOME 5000 PTZ Camera Replacing the Bubble | en 17 Bosch Security Systems, Inc.
Installing the Replacement Bubble Use the illustration below as a guide for replacing the bubble. 1 2 3 1 Safety Tab with M3x5 Screw 2 Bubble Assembly 3 M3x23L Screw (2 pieces) 6.2 18 en | Replacing the Bubble AUTODOME 5000 PTZ Camera 2013.07 | 1.3 | Installation Guide Bosch Security Systems, Inc.
Bubble Replacement Instructions 1. Loosen the two M3x23L screws (3) from the bubble on the camera. 2. Detach the Bubble Assembly (2) from the camera. 3. Remove the screw that secures the Safety Tether to the Bubble. Keep the screw to secure the bubble replacement.
Technical data Camera Dimensions 295.5 (11.63) 218.38 (8.6) 81.9 (3.22) mm (in.) 208 (8.19) 187 (7.36) Figure 7.1: AUTODOME 5000 Indoor/Outdoor Dimensions 1 Diameter without sunshield (indoor models) 2 Diameter with sunshield (outdoor models) 7 20 en | Technical data AUTODOME 5000 PTZ Camera 2013.
.
Bosch Security Systems, Inc. 850 Greenfield Road Lancaster, PA, 17601 USA www.boschsecurity.com © Bosch Security Systems, Inc., 2013.
デバイスBosch Appliances 5000 PTZの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bosch Appliances 5000 PTZをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBosch Appliances 5000 PTZの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bosch Appliances 5000 PTZの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bosch Appliances 5000 PTZで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bosch Appliances 5000 PTZを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBosch Appliances 5000 PTZの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bosch Appliances 5000 PTZに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBosch Appliances 5000 PTZデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。