Bosch AppliancesメーカーBC2600RAの使用説明書/サービス説明書
ページ先へ移動 of 18
SAR8854 Rev. 07/08 Installation Manual Bosch Eco26 + External Model BC2600RA Service Department: 1300 30 70 37 www.bosch.com.au To be installed and serviced only by an authorised person This appliance is not suitable for use as a pool heater The "authorised installing person" is responsible for: appliance.
2 Installation Instructions Potential dangers from accidents during installation and use are divided into the following three categories. Closely observe these warnings, they are critical to your safety.
3 Installation Instructions 1. Included Accessories The following accessories are included with the unit. Check for any missing items before starting installation. Q ’ ty Shape Part Tapping Screw 1 each Part Shape Q ’ ty 5 Owner's Guide, Installation Manual (this document) 2.
4 Installation Instructions 3. Before Installation Do Not Use Equipment for Purposes Other Than Those Specified • Do not use for other than increasing the temperature of the water supply, as unexpected accidents may occur as a result.
5 Installation Instructions 4. Choosing Installation Site * Locate the appliance in an area where water leakage from the unit or connections will not result in damage to the area adjacent to the appliance or to the lower floors of the structure.
6 Installation Instructions 5. Installation Clearances Before installing, check for the following: The location of the flue terminal must comply with the clearances shown on this page. If you are unsure about clearances not indicated here, in general refer to AS5601, or your local authority.
7 Installation Instructions CLEARANCES FOR FLUE TERMINAL (front of heater) The location of the flue terminal must comply with the clearances shown on this page. If you are unsure about clearances not indicated here, in general refer to AS5601, or your local authority.
8 Installation Instructions Illustration 6. Installation Check 4. Drill holes for the remaining four screws. 5. Hang the unit again by the first screw, and then insert and tighten the remaining four screws. 6. Take waterproofing measures so that water does not enter the building from screws mounting the device.
9 Installation Instructions Gas Connection 1) Fit a union to the water heater gas inlet for easy connec- tion and removal. The thread diameter is 20 mm. THIS DOES NOT INDICATE THE SIZE OF THE GAS SUPPLY. 2) Fit an AGA / NZGA approved isolating gas cock in the supply line adjacent to the water heater gas connection.
10 Installation Instructions 8. W ater Piping This appliance is suitable for potable water applications. Do not use this appliance if any part has been underwater. Immediately call a qualified service technician to inspect the appliance and replace any part of the control system and gas control which has been under water.
11 Installation Instructions Supply water piping • Do not use PVC, iron, or any piping which has been treated with chromates, boiler seal or other chemicals. • Pipe sizing from the cold water supply should be sized according to local BY LAWS for water supply.
12 Installation Instructions PLEASE FOLLOW LOCAL CODES ABOUT CONDENSATE PIPING. • This water heater is a high efficiency, fully condensing appliance which produces condensate during operation. Therefore, it is necessary to install condensate piping.
13 Installation Instructions Do not connect electrical power to the unit until all electrical wiring has been completed. Consult a qualified electrician for the electrical work. 10. Electrical Wiring This appliance must be electrically earthed in accordance with Electrical Authority Regulations.
14 Installation Instructions The remote controller will indicate when the neutralizer unit is in need of replacement by displaying an error code. Therefore, the remote controller should always be installed with this water heater in order to prevent an unexpected disruption of hot water service.
15 Installation Instructions Remote controller cord • Use remote controller cord for any extensions. • Install according to the National Electrical Code and all applicable local codes. Connecting Remote Controller Cord to Unit • Tie the redundant cord outside the water heater.
16 Installation Instructions (1) Open a hot water fixture and confirm that the Burner On lamp comes on, and that hot water is being produced. (If necessary, repeat until the air in the gas piping is bled out). * White smoke may be noticed from the exhaust vent during cold weather.
17 Installation Instructions Lighting Instructions This water heater does not have a pilot. It is equipped with an ignition device that automatically lights the burner. Do not try to light the burner by hand. 1. Read the safety information in the installation manual or on the right side of the water heater.
18 Installation Instructions 13. Dimensions 338 (VIEW FROM TOP) 279 243 136 100 60 HOT WATER OUTLET (R3/4) 177 48 58 141 179 GAS INLET (R3/4) DRAIN OUTLET (R1/2) COLD WATER INLET (R3/4) WIRING THROUGHWAYS 2-6.5 x 13 OBLONG HOLE 4- 13 4- 13 120 135 60 42 42 2- 6.
デバイスBosch Appliances BC2600RAの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bosch Appliances BC2600RAをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBosch Appliances BC2600RAの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bosch Appliances BC2600RAの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bosch Appliances BC2600RAで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bosch Appliances BC2600RAを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBosch Appliances BC2600RAの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bosch Appliances BC2600RAに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBosch Appliances BC2600RAデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。