Bosch AppliancesメーカーIVMD 1.0の使用説明書/サービス説明書
ページ先へ移動 of 44
IVMD 1.0 Intelligent Video Motion Detection en Configuration Instructions.
Copyright This manual is copyright protected by Bosch Security Systems. All rights reserved. No part of this document may be reproduced or t ransmitted for any purpose, by whatever method and by whatever means, electronically or mechanically, without the express writt en permission of Bosch Security Systems.
IVMD | Configuration instructions T able of Cont ents | en 1 BOSCH Security Syst ems 1.0 | 2006.04 T able of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Requirements . . . . . . . . . . . .
2 en | T able of Cont ents IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems.
IVMD | Configuration instructions Introducti on | en 3 BOSCH Security Syst ems 1.0 | 2006.04 1 Introduction IVMD (Intelligent Video Motion Detection) is a software algorithm that detects movements of objects within an environ- ment monitored by a video came ra and generates alarm events that can be processed further in a CCTV system.
4 en | Introduction IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems.
IVMD | Configuration instructions Requirements | en 5 BOSCH Security Syst ems 1.0 | 2006.04 2 Requir ements You will need the Configuration Manager software to configure IVMD. This must be installed on a Windows PC that can commu- nicate with the respective device over a network.
6 en | Requirements IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems 2.1.1 Requesting the Activation Key 3. Connect to the Internet on a PC and open this page in a Web browser: – https://activation.boschsecurity.com/ (this page always appears in English) You will see the BOSCH Security Systems License Man- ager .
IVMD | Configuration instructions Requirements | en 7 BOSCH Security Syst ems 1.0 | 2006.04 9. If you h ave clic ked the Email Activation Key link, you will see a dialog in which you can enter two e-mail addres ses for recipients. 10. Open the Web browser vi ew of the device again.
8 en | Requirements IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems If the image co nsists to a certain extent of nothing but moving objects – in other words if objects cannot be distinguished from each other or from the background – the motion of an indi- vidual object cannot be detect ed (e.
IVMD | Configuration instructions Configuration | en 9 BOSCH Security Syst ems 1.0 | 2006.04 3 Configuration IVMD can only be configured with the Configuration Manager. The Configuration Manager can be installed on any Windows PC. 1. Start the Configuration Manager.
10 en | Configuration IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems 3.1 VCA tab (Video content analy sis) The camera image appears on the right.
IVMD | Configuration instructions Configuration | en 11 BOSCH Security Syst ems 1.0 | 2006.04 Alarm state This field shows whether IVMD has generated an alarm event with the current settings. Object markings Objects that generate an alarm event under the current settings appear on the camera image inside a red outline.
12 en | Configuration IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems.
IVMD | Configuration instructions Area settings | en 13 BOSCH Security Syst ems 1.0 | 2006.04 4 Area settings 4.1 The basics The camera 'sees' a selected are a that is displayed as a single, constantly refreshed image. Objects Objects are typically people or ve hicles moving within the area seen by the camera.
14 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems Calibration If you wish to filter out objects according to their size or speed, for each camera position a link must be made between the size of the real-life situation and the dimensions as they appear on the camera image.
IVMD | Configuration instructions Area settings | en 15 BOSCH Security Syst ems 1.0 | 2006.04 4.2 The Area settings windo w If you have previously reset all the settings to their defaults, the Area se.
16 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems 4.2.1 Detector field Detector fields are displayed as framed areas with a grid pat- tern.
IVMD | Configuration instructions Area settings | en 17 BOSCH Security Syst ems 1.0 | 2006.04 Moving the mouse cursor over a node highlights it more brightly: – You can reposition th e node using drag&drop. – You can delete the node using the context menu.
18 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems 4.2.2 Detector field context menu Overview of commands: Cut Deletes the detector field – the field is copied to the clipboard and can be inserted again if required.
IVMD | Configuration instructions Area settings | en 19 BOSCH Security Syst ems 1.0 | 2006.04 4.2.3 Area sett ings contex t menu This context menu appears in the Area settings window when you right click outside a detect or field in the camera image .
20 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems Global Settings Here you can specify a minimum and maxi- mum size for all object s that will generate an alarm event. Objects that are smaller or larger than the specified sizes will be ignored an d this will save computing power as a result.
IVMD | Configuration instructions Area settings | en 21 BOSCH Security Syst ems 1.0 | 2006.04 4.3 Calibration Calibration is only necessary if you want the speed and size of detected objects to be interpre ted correctly. You do not need to perform this step if you d o no t want objects to be filtered on the basis of these two properties.
22 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems Position one of the red cubes ov er an object that you wish to trigger an alarm event. Adjust the cube to the size of this object. The second cube changes its size to suit the selected perspec- tive.
IVMD | Configuration instructions Area settings | en 23 BOSCH Security Syst ems 1.0 | 2006.04 4.3.1 Adjusting the calibration plane This section provides an overview of the ways in which the cali- bration plane can be adjusted.
24 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems The calibration mode also provid es a context menu with the fol- lowing commands: Anchor point Corner of a cube The size of both cubes changes – both cubes always represent the same size.
IVMD | Configuration instructions Area settings | en 25 BOSCH Security Syst ems 1.0 | 2006.04 4.3.2 Viewing and editing calibration settings The context menu for the calibrati on mode allows you to view the current calibration settings.
26 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems Roll angle: The angle by which the calibration plane is tilted.
IVMD | Configuration instructions Area settings | en 27 BOSCH Security Syst ems 1.0 | 2006.04 The pixel pitch is obtained by di viding the image sensor size by the number of pixels. For se nsors with 596 pixels, for example, this gives: 1/2 inch: 5.95 mm/596 = 0.
28 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems 4.4 Proper ties of a detect o r field The Properties of Detector Field dialog is opened from the context menu of the Area setti ngs window (refer to page 19).
IVMD | Configuration instructions Area settings | en 29 BOSCH Security Syst ems 1.0 | 2006.04 Objects cannot be detected a ccording to their properties unless the system has been calibrated for the current c amera position ( Section 4.3 Calibration , page 21).
30 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems Trigger Mode: An alarm event is generated when... Entering .
IVMD | Configuration instructions Area settings | en 31 BOSCH Security Syst ems 1.0 | 2006.04 Object direction filter Off Objects are not fi ltered according to their direction of movement On Objects will only generate an alarm event when they move in the selected direction.
32 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems If you have activated Direction under Show in the context menu of the Area settings window (see page 19), .
IVMD | Configuration instructions Area settings | en 33 BOSCH Security Syst ems 1.0 | 2006.04 An object motion filter (if set) is shown by additional moving white (maximum limit) and yellow (minimum limit) squares being displayed inside the direction indicato r.
34 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems You will find all of the commands in the context menu. Examples of areas that could be defined as non-sensitive: – Railroad: Passing trains can trigger unwanted motion alarms.
IVMD | Configuration instructions Area settings | en 35 BOSCH Security Syst ems 1.0 | 2006.04 The following commands are available: Save and Exit Editor The settings are saved. Yo u exit the Editor for the sensitive area. Undo The last action you carried out is undone.
36 en | Area settings IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems 4.6 Statistics The statistics for a detector field he lp you to refine the filter cri- teria for objects.
IVMD | Configuration instructions Area settings | en 37 BOSCH Security Syst ems 1.0 | 2006.04 (see page 28). Areas that are ou tside the defined limits are grayed. The lines indicate the number of objects for which the respec- tive value was detected.
38 en | Display of Measurements IVMD | Configuration instructions 1.0 | 2006.04 BOSCH Security Syst ems 5 Displa y of Measurements When you are working with the E nglish software interface, mea- surements can be displayed ac cording to the imperial system.
IVMD | Configuration instructions Contact and Service | en 39 BOSCH Security Syst ems 1.0 | 2006.04 6 Contact and Ser vice Contact address Bosch Sicherheitssysteme GmbH Robert-Koch-Straße 100 85521 Ottobrunn Germany E-mail: de.securitysystems@bosch.com Internet: www.
40 en | Contact and Servic e IVMD | Configuration instru ctions 1.0 | 2006.04 BOSCH Security Syst ems Service and support If you have any questions about the programs from the VIDOS Pro Suite, you can find further information on the Internet at: www.vidos.
IVMD | Configuration instructions | en 41 BOSCH Security Syst ems 1.0 | 2006.04 Inde x A Analysis type 10 Anchor point calibration 23 C Calibration plane 23 Contact address 39 Cube calibration 24 Cube.
Bosch Sicherheitssysteme GmbH Robert-Koch-Straße 100 85521 Ottobrunn Germany Telephone +4 9 (0) 89 6290-0 Fax +49 (0) 89 6290-1020 www.bosch-securitysystems.
デバイスBosch Appliances IVMD 1.0の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bosch Appliances IVMD 1.0をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBosch Appliances IVMD 1.0の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bosch Appliances IVMD 1.0の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bosch Appliances IVMD 1.0で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bosch Appliances IVMD 1.0を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBosch Appliances IVMD 1.0の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bosch Appliances IVMD 1.0に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBosch Appliances IVMD 1.0デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
