Bosch AppliancesメーカーLBB 4162の使用説明書/サービス説明書
ページ先へ移動 of 20
DCN Next Generation Automatic Camera Control en Softwa re User Manual LBB 4162/00 LBB 4188/00.
About this manual This user manual is divide d into three chapter s. Chapters 1 and 2 provide background information and chapter 3 provides detailed user information as follows: • Chapter 1 - Automatic Ca mera Control - containing general inf ormation about the Automatic Camera C ontrol software , and the two different version s available.
DCN Next Generation Automatic Camer a Control en | 3 Table of contents 1 Automatic camera control .................................... 4 1.1 About Automatic Camera Control ...................... 4 1.1.1 What is Automatic C amera Control? .............
DCN Next Generation Automatic Camer a Control en | 4 1 A u to m a ti c ca m e r a c o n tr o l 1.1 About Automatic Camera Control 1.1.1 What is Automatic Camer a Control? The Automatic Camera Contr ol software is desi gned to interface DC N Next Generation con gress systems with Bosch Allegiant swit chers or a single Bosch AutoDome camera.
DCN Next Generation Automatic Camer a Control en | 5 2 G e ttin g s tar te d 2.1 Starting the Automatic Camera Control software 2.1.1 The Startup screen The Automatic Camera Cont rol program is started from the Start up screen (shown bel ow). Figure 1 The Startu p screen.
DCN Next Generation Automatic Camer a Control en | 6 Control Installation is created. Please refer to paragraph 2.1, for inform ation about starting the module. i Note Before beginning camer a installation, it is important to make sure that the Allegiant vide o switcher, system cameras and monitors are properly connected and installed.
DCN Next Generation Automatic Camer a Control en | 7 2.3.7 Using Help This gives information on ho w to use the help facility. To access the ‘Using Help’ facility: • Select the ‘Help ’ menu and click on ‘ Usi ng Help’ . A list of topics is given.
DCN Next Generation Automatic Camer a Control en | 8 3 Using Automat ic Camera Cont rol 3.1 The camera installation main window The Camera Installation ma in window is used to assign fixed c ameras and c amera positions (on preposition cameras) to DC N Next Generation units.
DCN Next Generation Automatic Camer a Control en | 9 3.1.1 The menu bar All menu options referred to in this user manual are contained within the menu bar located under the title bar at the top of the Camera Installation wind ow. The full list of menu op tions is as follows: F ile S ettings!.
DCN Next Generation Automatic Camer a Control en | 10 3.2.1 Specifying the overview camer a For Allegiant Video Switchers (AVS) Camera 1 is always reserved for the overview. For Direct Camera Control (DCC) the hi ghest pre-p osition is reserved for the overview.
DCN Next Generation Automatic Camer a Control en | 11 16 characters) entered in the ‘Cam era ID:’ edit field. This, for example, could be used to give each camera a descriptive ID relati ng to the position of the camera in the conference ven ue. This text appea rs on the operator monitor but not on audience monitors.
DCN Next Generation Automatic Camer a Control en | 12 i Note If ‘ Double Seat Text’ is selected in the ‘ Settings’ dialogue box, two lines of text can be entered. Figure 13 Seat (or unit) text editing i Note In case of DDC is is not possible to enter a seat text.
DCN Next Generation Automatic Camer a Control en | 13 The Seat number, camera number, preposition number (if applicable) and screen text is stored and displayed in the ‘Assignments:’ list. An e xample of the ‘Assignments:’ list is shown below.
DCN Next Generation Automatic Camer a Control en | 14 To enable the settin gs window: • Click on the ‘Settings…’ menu. The following window appears.
DCN Next Generation Automatic Camer a Control en | 15 i Note It is recommended that the number se lected corresponds to the actual n umber of audience monitors present in the venue. If the number selected is higher than this, there may be some reduction in system performance.
DCN Next Generation Automatic Camer a Control en | 16 situations where you wi sh to use more tha n one configuration with an installation file. i Note The DCN cont rol PC can only import information relating to seat numbers which are present in the current System Installation file.
DCN Next Generation Automatic Camer a Control en | 17 become iconized in the Windows ta skbar. To re-ente r Automatic Camera Control: • Click on the Automatic Camera Control module icon.
DCN Next Generation Automatic Camer a Control en | 18 Bosch Security Systems B.V. | 2005 January | 9922 141 70491.
.
For more information please visit www.boschsecuritysystems.com © 2005 Bosch Security Systems B.V. Data subject to ch ange without notice January 2005 | 9922 141 7049 1.
デバイスBosch Appliances LBB 4162の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bosch Appliances LBB 4162をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBosch Appliances LBB 4162の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bosch Appliances LBB 4162の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bosch Appliances LBB 4162で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bosch Appliances LBB 4162を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBosch Appliances LBB 4162の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bosch Appliances LBB 4162に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBosch Appliances LBB 4162デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。