Bosch AppliancesメーカーNBN-733の使用説明書/サービス説明書
ページ先へ移動 of 44
DINION HD 720p60 NBN-733 en Installation Manual.
.
DINION HD Table of Cont ents | en 3 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 T able of Contents 1S a f e t y 5 1.1 Safety precautions 5 1.2 Important safety instructions 6 1.3 Connection in applications 7 1.4 FCC & ICES compliance 8 1.
4 en | Table of Cont ents DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 5 Installation 18 5.1 Lens mounting 18 5.2 Mounting the camera 20 5.3 Network (and power) connector 21 5.4 Power connector 22 5.5 Alarm and relay connector 23 5.
DINION HD Safety | en 5 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 1S a f e t y 1.1 Safety precautions DANGER! High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product.
6 en | Safety DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 1.2 Impor tant safety instructions Read, follow, and retain for future reference all of the following safety instructions. Follow all warnings on the unit and in the operating instructions be fore operati ng the unit.
DINION HD Safety | en 7 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 1.3 Connection in applications Grounding Safety (power) ground is indi cated by the symbol on the rear of the camera. U.S.A.: - section 810 of the National Electrical Code, ANSI/NFPA No.
8 en | Safety DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 1.4 FCC & ICES compliance FCC & ICES Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules .
DINION HD Safety | en 9 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 1.5 MicroSD cards Bosch Security systems reco mmends that local storage on microSD card should only be used for alarm recordin g and Automatic Network Replenishm ent (ANR) applications.
10 en | Safety DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 1.7 Bosch notices Video lo ss Video loss is inherent to d igital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information.
DINION HD Safety | en 11 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 1.8 Copyrights The firmware uses the fonts "Adobe-Helvetica-Bold-R-Normal-- 24-240-75-75-P-138-ISO1.
12 en | Introduction DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 2 Introduction 2.1 F eatur es The 720p HD IP Day/Night camera is a high-performance, surveillance color camera. The camera uses H.264 compression technology to give clear images while reducing bandwidth and storage requirements.
DINION HD Sys tem Information | en 13 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 3 Syst em Information 3.1 Over vie w of functions The camera incorporates a network video server. Its primary function is to encode video and control data for transmission over an IP network.
14 en | Syst em Information DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 3.1.5 Audio Two-way duplex audio is available in the unit for live voice communications or audio recording. 3.1.6 Alarm I/O The alarm input can be used to control the functionality of the unit.
DINION HD Sys tem Information | en 15 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 3.1.12 Encryption The unit offers a variety of options fo r protection against unauthorized reading. Web browser connections can be protected using HTTPS.
16 en | Syst em Information DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 3.2 Operation with external sy stems The camera can be used with a variety of Bosch systems.
DINION HD Planning | en 17 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 4 Planning 4.1 Unpacking Unpack carefully and handle the equipment with care.
18 en | Installation DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 5 Installation 5.1 Lens mounting The camera accepts CS or C-mount lenses. DC-iris lenses are recommended for best performanc e. The camera automatically detects the type of lens and optimizes performance accordingly.
DINION HD Installation | en 19 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 Note If a short circuit is detected on the lens connector, the lens circuit is automatically disabled to avoid internal damage. Remove the lens connector an d check the pin connections.
20 en | Installation DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 5.2 Mounting the camera The camera can be mounted eith er from the top or from the bottom (1/4" 20 UNC thread). Figure 5.2 Mounting a camera 1/4”-20 UNC CAUTION! Do not expose the image sensors to direct sunlight.
DINION HD Installation | en 21 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 5.3 Ne tw ork (and power) connect or Figu re 5.3 Ne twork connection – Connect the camera to a 10/100 Base-T network. – Use STP Category 5e cable with RJ45 connectors (the camera network socket is Auto MDIX compliant).
22 en | Installation DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 5.4 Po wer connector Figure 5.4 Pow er co nnection Connect a SELV-LPS or a SELV Class 2 power supply with a rated supply voltage of 24 VAC or 12 VDC as follows: – Use AWG16 to 22 stranded wire or AWG16 to 26 solid wire; cut back 5 mm (0.
DINION HD Installation | en 23 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 5.5 Alarm and rela y connector Figu re 5.5 Alarm and relay connector pins – Max. wire diameter AWG 22-28 for both stranded and solid; cut back 5 mm (0.
24 en | Installation DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 5.6 Audio connectors Figure 5.6 Audio connectors Connect audio devices to the Audio In and Audio Out connectors. The unit has full-duplex mono audio.
DINION HD Installation | en 25 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 5.7 Local st orage Figu re 5.7 Inser ti ng an microSD card 1. Unscrew the card slot cover. 2. Slide the microSD card into the slot until it locks in place.
26 en | Installation DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 5.8 Video ser vice monitor connector Figure 5.8 Video ser vice monit or connector 1. Connect a service monitor to the com pos ite video connector (INSTALL) to aid installation (cable S1460).
DINION HD Installation | en 27 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 5.9 Data connector Figu re 5.9 Data connector pins The data connector is used to connect the control data coming out of the camera to external devices.
28 en | Install Wizard DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 6 Install Wizard 6.1 Using the camera install wizard The Menu button on the rear panel is u sed for accessing the camera install wizard.
DINION HD Install Wizard | en 29 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 6.1.1 Adjustment procedure A monitor must be connected to the video service connector to use the wizard. (After power-up, wait 20 seconds before attempting to open the install wizard.
30 en | Install Wizard DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 5. Briefly press the Menu button to start the automatic motorized (Auto MBF) back focus adjustment. – You will hear the motori zed automatic back focus process running.
DINION HD Camera configuration | en 31 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 7 Camera configur ation The camera normally provides an optimal picture without the need for further adjustments. Config uration of the camera is carried out via the network using a web browser.
32 en | Camera configuration DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 7.3 T rue Day/Night switching The camera is equipped with a motorized IR filter. The mechanical IR filter is taken out of the optical path in low-light applications.
DINION HD Brow ser connection | en 33 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 8 Bro wser connection A computer with Microsoft Internet Ex plorer can be used to receive live images from the camera, control the camera, and replay stored sequences.
34 en | T roubleshoo ting DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 9 T rouble shooting 9.1 F unction test The camera offers a variety of configuration options. Theref ore, check that it works properly afte r installation and configuration.
DINION HD T roubleshoo ting | en 35 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 9.2 Resolving pr oblems The following table is intended to help identify the causes of malfunctions and correct them where possible. Malfunction Possible causes Solution No image transmission to remote location.
36 en | T roubleshoo ting DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems No audio transmission to remote station. Hardware fault. Check that all connected audio units are operating correctly. Faulty cable connections.
DINION HD T roubleshoo ting | en 37 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 9.3 Customer ser vice If a fault cannot be resolved, please contact your supplier or system integrator, or go dire ctly to Bosch Security Systems Customer Servi ce.
38 en | Maintenance DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems 10 Maintenance 10.1 T esting the ne tw ork connection The ping command can be used to check the con nection between two IP addresses. This allows testing whether a device is active in the network.
DINION HD Maintenance | en 39 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 Configuring the Terminal Before the terminal program can communicate with the cam era, the transmission parameters must be matched.
40 en | Maintenance DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems Reboot Briefly interrupt the power supply to the camera for a reboot (disconnect the power supply unit from the mains supply and switch on again after a few seconds).
DINION HD T ech nical Data | en 41 Bosch Security Systems Installation Manual AM18-Q0614 | v1.0 | 2012.09 11 T echnical Data 11.1 Specifications Imager 1/3-inch CMOS HD sensor Image resolution 1280 × 720 pixels Rated supply voltage 12 VDC, 600 mA 24 VAC, 500 mA, 50/60 H z PoE 48 VDC, 175 mA Minimum illumination 30 IRE, F1.
42 en | T echnical Data DINION HD AM18-Q0614 | v1.0 | 2012.09 Installation Manual Bosch Security Systems Stream (max.) 72 0p50/60 Group of pictures IP, IBP, IBBP Network protocols IPv4, IPv6, UDP, TCP, HTTP, HTTPS, RTP, IGMPV2/ V3, ICMP, RTSP, FTP, Telnet, ARP, DHCP, SNTP,SNMP (V1, MIB-II), 802.
.
Bosch Security Systems www.boschsecurity.com © Bosch Security Systems, 2012.
デバイスBosch Appliances NBN-733の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bosch Appliances NBN-733をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBosch Appliances NBN-733の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bosch Appliances NBN-733の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bosch Appliances NBN-733で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bosch Appliances NBN-733を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBosch Appliances NBN-733の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bosch Appliances NBN-733に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBosch Appliances NBN-733デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。