3ComメーカーiQ 10の使用説明書/サービス説明書
ページ先へ移動 of 24
iQ SERIES USER MANUAL iQ 10, iQ 10P, iQ 10C AND iQ 10PC MODELS.
.
CONTENTS 1. Introduction 2. Unpacking 3. Connectors/Cabling 4. Amplification & Power Handling 5. Operation 6. Equalisation 7. Arraying 8. Dimensions 9. Rigging & Suspension General Safety Advice Skeletal Flying SECUR – ET VPC Pole Clamp SECUR ET – VEB Eyebolt Suspension T russ 10.
4 1. Introduction Thank You for purchasi ng Tannoy PowerDual™ iQ 10. The iQ 10 has been desig ned for live and fixed installation music and speech sound reinforcement applications. They are spec ifically design ed for use in venues, theatres, arenas and di stributed systems in stadiu ms.
5 Cable choice con sists mainly of selecting the correct cross sectional area in relation to the cable length and t he load impedance. A small cross sectional area would increase the cables series resi stance, i nducing power loss and resp onse variations (damping factor).
6. Equalisation Over equalisation can reduce system headr o om, and introduce phase di stortion resulting in greater proble ms than cures. If equalisat ion is required then it sho uld be applied gently and smoothly. Violent equali sat ion will be detrimental to the overall sound quality.
8. Dimensions IQ 10 & iQ 10P 7.
508.0 680.0 540.0 iQ 10C & iQ 10PC 8.
9. Rigging & Suspension General Safety Advice The Tannoy Professional hardwa re covered in this guide has be en designed to offer quick, simple, cost effective and secure solution s for mounting specific Tannoy Professional loudspeakers. This ha rdware has been designed a nd manufactured with a high safety load factor for its specific role.
The iQ 10 & iQ 10P is supplied as a ‘skeletal’ desi gn loudspeaker, which can be used both indoors and out due to it’s weatherpr oof exterior.
SECUR – ET VPC Pole Clamp SECUR ET – VEB Eyebolt Description Quantity VPC Pole Clamp 1 M10 Washer 1 M10 x 50mm Screw 1 M10 Nyloc Nut (Black) 1 The Tannoy iQ 10C & iQ 10PC loudspe ake rs can be flown with high quality VEB M10 eyebolts with collar to BS4278:1984.
SINGLE iQ SUSPENSION TRUSS (By ATM ™ ) The iQ suspension truss is an economic al solutio n to suspending a single p urpose loudspeaker array from two or thre e fixed stru ctural attachment points. The iQ Suspen sion Truss is designed to hol d the loudspeakers at the optimum spl ay angle to optimize cluster performance.
Typical Suspension Truss applications – 2xi Q1 0 C 13 2 x iQ 10C & 2 x iQ 18B.
10. Performance Data FREQUENCY RESPONSE (iQ 10) Unprocessed Anechoic Freque ncy Respon se, 1 watt @ 1 metre on axis FREQUENCY RESPONSE – Midrange (iQ 10) System Frequency Response (with syst em cont.
FREQUENCY RESPONSE – High Frequency (iQ 10) INPUT IMPEDANCE – Midrange (iQ 10).
INPUT IMPEDANCE – High Frequency (iQ 10) FREQUENCY RESPONSE – Passive (iQ 10P) System Frequency Response @ 1m on axis (iQ 10P) 16.
iQ 10P INPUT IMPEDANCE A comprehensive range of measurem ents including off axis frequenc y response curves, octave & third octave polar diagrams (singl e & two cabinet arrays) and beam width plots as well as Ease ™ data can be downloaded from http:// www .
11. Technical Specifications Frequency Response (1) + /- 3dB 180Hz – 19kHz Nominal Dispersion 60° × 40° (H × V) Maximum SPL @ 1m (2) 129dB Average (2) 135dB P eak (10ms) Driver Complement 1 x 250mm (10”) Pow erDual™ Components iQ 10 – Mi drange iQ 10 – High Frequency iQ 10P - System Frequency Band (3) 180Hz – 2.
19 12. System Configurations & OEM Controllers Passive or Biamp? The iQ 10 is supplied as standard for bi -amp operation, therefore there is no internal passive crossover network between the mid & hf units. The Bi-amp controller parameters below must be adhere d to for optimum performance.
20 Passive System Parameters (iQ 10P & iQ 10PC) With the vast array of digital loudspea ker management systems avai lable it is inevitable that the user may opt to use a c ontroller other than the TDX1 or TDX2 as part of a large scale integrated system.
21 13. iQ 10 Service Parts and Accessories Part Number Description 7900 0607 Driver Kit Type 2519 (LF) 7900 0609 Recone Kit Type 2519 (LF) 7900 0608 Driver Kit Type 0278 (HF) 7900 0610 Diaphragm Ty pe.
15. Declaration of Confor mity The following apparatus is/are manufa ctured in the United Kingdo m by Tannoy Ltd of Rosehall Industria l estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Comp atibility Standards and Directives relevant to Domestic Electrical Equipment.
.
Tannoy United Kingdom T: 00 44 (0) 1236 420199 E: enquiries@tannoy.com Tannoy North America T: 00 1 (519) 745 1158 E: inquiries@tannoyna.com anfragen@tannoy.com Tannoy France T: 00 33 (0)1 7036 7473 E: ventes@tannoy.com Tannoy adopts a policy of continuous improvement and product specification is subject to change.
デバイス3Com iQ 10の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
3Com iQ 10をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこには3Com iQ 10の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。3Com iQ 10の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。3Com iQ 10で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
3Com iQ 10を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又は3Com iQ 10の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、3Com iQ 10に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわち3Com iQ 10デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。