BostitchメーカーGT18B01の使用説明書/サービス説明書
ページ先へ移動 of 30
1 GT18B01 HYDRAULIC POWER UNIT S AFETY , O PERA TION AND M AINTENANCE SER VICE MANUAL WARNING Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .
2.
3 T ABLE OF CONTENTS For the nearest authorized and certifi ed dealer , call Stanley Hydraulic T ools at the number listed on the back of this manual and ask for a Customer Service Representative. SERVICING THE ST ANLEY POWER UNIT : This manual contains safety , operation, and routine mainte- nance instructions.
4 CERTIFICATE OF CONFORMITY Hy draulic Tools ______________________________________________________________________ I, the undersigned: Burrows, James Surname and First names Hereby certify that the c onstruction plant or equipment specif ied hereunder: 1.
5 Safety symbols and signal words, as shown below , are used to emphasize all operator , maintenance and repair actions which, if not strictly followed, could result in a life-threatening situation, bodily injury or damage to equip- ment.
6 T ool operators and maintenance personnel must always comply with the safety precau- tions given in this manual and on the stickers and tags attached to the equipment. These safety precautions are given for your safety . Review them carefully before operat- ing the tool and before performing general maintenance or repairs.
7 T OOL STICKERS & T AGS 65458 Sound Power Decal 62302 Power Unit Dash Decal 62300 CHOKE D ANGER PULL TO ST ART PUSH TO R UN 62300 Single Circuit 28322 CE Decal AUTO IDLE OFF AUTO IDLE ON R U 6230.
8 HOSE TYPES Hydraulic hose types authorized for use with Stanley Hydraulic T ools are as follows: ➊ Certifi ed non-conductive ➋ Wire-braided (conductive) ➌ Fabric-braided (not certifi ed or labeled non-conductive) Hose ➊ listed above is the only hose authorized for use near electrical conductors.
9 HTMA REQUIREMENTS FLOW RA TE TOOL OPERA TING PRESSURE (at the power supply outlet) SYSTEM RELIEF V AL VE SETTING (at the power supply outlet) MAXIMUM BACK PRESSURE (at tool end of the return hose) Measured at a max. fl uid viscosity of: (at min. operating temperature) TEMPERA TURE Suffi cient heat rejection capacity to limit max.
10 Chevron A W-MV -32 Exxon "Univis" J-26 Mobil D.T .E. 13 Gulf "Harmony" AW -HVI-150-32 Shell "T ellus" T -32 T exaco "Rando" HD-AZ Union "Unax" AW -WR-32 T erresolve EnviroLogic 132 4. HYDRA ULIC CONNECTIONS The recommended hose length is 25 ft/8 m with a 1/2 inch/12.
11 CONTROL P ANEL RETURN PRESSURE H.T .M.A. 1/2 INCH MALE QUICK DISCONNECT COUPLER H.T .M.A. 1/2 INCH FE- MALE QUICK DISCON- NECT COUPLER 1/2 INCH I.D. HOSE, 25 FT LONG WITH 2500 PSI/ 172 BAR RA TING AND 4 T O 1 SAFETY F ACTOR PRESSURE RETURN 1/2 INCH MALE PIPE HOSE END 1/2 INCH MALE PIPE HOSE END ADAPTER, 3/8 INCH MALE PIPE x -8 SAE O-RING H.
12 CONTROLS This unit is equipped with an advanced proportional engine control system. It provides a means of controlling engine speed by adjusting the fuel control lever with an actuator .
13 OPERA TION COLD WEA THER ST ARTUP 1. Use the procedures described under "ST ARTUP" and then follow the procedure below . 2. Hydraulic fl uids are thicker in cold weather . Therefore, it is recommended that the engine be run at low idle long enough to bring the fl uid temperature up to a minimum of 50°F/10°C.
14 ST ORAGE • Clean the unit thoroughly before storage. Do not use water pressure. • Always store the unit in a clean and dry facility . • If the unit will be stored for a prolonged period (over 30 days), add a fuel additive to the fuel tank to prevent the fuel from gumming.
15 CHECKING PERFORMANCE CONTROL™ (ELECTRONIC GOVERNOR-ST A TIC CHECK) T o determine whether a governor problem is being caused by the actuator or the control module, perform the following static check exactly in order shown. A pair of jumper wires and a known good 12-volt battery is required.
16 F AUL T CODES 1 APECS unit not calibrated yes Have engine serviced by an Authorized Stanley Dealer . 2 Engine speed excessive yes Have engine serviced by an Authorized Stanley Dealer . 3 Engine speed unusually low yes Have engine serviced by an Authorized Stanley Dealer .
17 GENERAL T ests and adjustments should be performed periodically to ensure the power unit is operating at maximum effi ciency . Stanley Circuit T ester (part number 04182) is recommend- ed. This tester can be used to isolate problems in both the engine and hydraulic system prior to any power unit disas- sembly .
18 Engine will not start. Flow selector switch not in the Make sure the fl ow selector switch is in OFF position. the OFF position when starting. Battery not connected. Attach battery cables, check wires. Weak battery . T est battery , charge or replace.
19 Engine: ....................................................................................................................... ........................................ 18 hp Briggs Capacity .........................................................
20 SER VICE GENERAL Service instructions in this section are limited to parts and components other than the engine and hydraulic pump. Other major components should be serviced by representa- tives of.
21 Be sure the tapered cone surfaces of the bushing and blower hub are clean and free of anti-seize lubricants. CA UTION 2. Disconnect the wiring harness (See Figure 4, Wiring Diagrams for the correct connections). 3.Follow steps 1 through 4 under "Manifold Assembly Re- moval".
22 Assemble the bushing and blower hub with the bolts inserted (but not tightened) through the drilled holes in the blower hub and into the tapped holes in the bushing. With the key in the shaft, slide assembly into position on the shaft and tighten the setscrew over the key (if equipped).
23 SER VICE HYDRAULIC T ANK, COOLER & FIL TER ASSEMBL Y (see fi gure 1, 2 & 3) 1. First remove the hydraulic fl uid from the tank by either pumping it out with a portable drill pump or draining it into a container . 2. Remove the cooler guard (20, fi g.
24 FIGURE 1. BRIGGS ENGINE ASSEMBL Y 5 6 3 5 3 7 3 4 3 6 5 2 4 4 2 7 5 0 5 1 8 2 6 2 8 4 5 3 0 4 3 3 0 4 7 3 3 3 1 3 0 3 2 2 9 4 9 4 8 1 7 1 6 1 4 1 3 1 2 1 1 9 1 0 4 1 5 2 0 2 1 2 3 1 8 2 5 2 2 1 9 4.
25 ITEM P/N Q T Y DESCRIPTION 1 36150 1 Muffl er 1A 65456 1 Spark Arrester 2 36151 1 Heat Shield 3 36152 2 Screw , Hex W asher 4 59007 1 Briggs Engine 5 56656 1 Coupling 6 07819 1 Square Key 7 07860 .
26 FIGURE 2. FRAME P ARTS ITEM P/N Q T Y DESCRIPTION 1 370502 7 Capscrew , 5/16 in. -18 UNC 2 03906 7 Nylock Nut, 5/16 in. -18 UNC 3 62270 1 Handle, Rear Lift 4 58857 1 Coupler , Male 3/8 in., -8 SAE 5 58856 1 Coupler , Female 3/8 in., -8 SAE 6 60962 2 Capscrew , 1/4 in.
27 ITEM P/N QTY DESCRIPTION 1 59130 1 Manifold Assy , Single Circuit 2 59104 1 Hose Barb, 3/4 in. Hose x 3/4 in. Pipe 3 62199 4 Hose Clamp 4 350000 1 Elbow , 45° Straight Thread 5 02773 1 Adapter 6 5.
28 RECTIFIER WIRE WHITE CONTROLLER TO MAGNETO WIRE ON ENGINE GRA Y WIRE OIL PRESSURE SWITCH FUEL SHUTOFF RED WIRE - THROTTLE CONTROL SWITCH (NOTE: PLUG BEHIND SWITCH WITH BLUE & YELLOW WIRES GOES .
29 Stanley Hydraulic T ools (hereinafter called “Stanley”), subject to the exceptions contained below , warrants new hydraulic tools for a period of one year from the date of sale to the fi rst r.
30 Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie OR 97267-5698 503-659-5660 F AX 503-652-1780 www .stanley-hydraulic-tools.com.
デバイスBostitch GT18B01の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bostitch GT18B01をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBostitch GT18B01の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bostitch GT18B01の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bostitch GT18B01で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bostitch GT18B01を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBostitch GT18B01の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bostitch GT18B01に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBostitch GT18B01デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
