BOXLIGHTメーカーMP-58iの使用説明書/サービス説明書
ページ先へ移動 of 48
Projector MP-57i / MP-58i User's Manual - Operating Guide Thank you for purchasing this projector! 1.800.762.5757 www.boxlight.com ©2004, BOXLIGHT Corporation. All rights reserved.This manual may not be copied in any media or form without the written consent of the manufacturer.
TRADEMARK ACKNOWLEDGMENT • VGA and XGA are registered trademarks of the International Business Machines Corporation. • Apple and Mac are registered trademarks of Apple Computer, Inc. • VESA and SVGA are trademarks of the Video Electronics Standard Association.
2 Projector Features Projector Features Preparation Preparation ● Ultra High Brightness Crisp, ultra-bright presentations is achieved by using a UHB (ultra high brightness) lamp and a highly efficient optical system. ● Whisper Mode Equipped Special mode is available for reducing projector noise to achieve quieter operation.
3 Contents Contents Projector Features … … … … … … … … … … … … … … 2 Preparation … … … … … … … … … … … … … … … … … … … … 2 Part Name.
4 Part Names Part Names Projector 1 Elevator button 2 Elevator foot 3 Remote sensor 4 Lens cap 5 Lens The picture is projected from here. 6 Filter cover An air filter is inside.
I N T E R IN P U T M 1 -D RG B B NG S- V I DEO S T ANDBY / O N T E MP VIDEO C OM P ON E N T LA M P KEY S T O N E SEA R C H R E S E T M E N U FOCUS LE NS SHI F T ZO O M ST ANDBY/ON VIDEO LASER INDICA T.
6 Setting Up Setting Up Arrangement WARNING • Before installation, make sure that the projector is turned off and the power code is disconnected. • Do not set up and move the projector, while it is hot. • Install the projector in a suitable environment according to instructions of the “User’s Manual – Safety Guide” and this manual.
I N T E R I N P U T M 1 -D R G B BNG S- V I D E O S T AN DBY / O N T E M P V ID E O C O M P O N E N T LA M P K E Y S T ON E SE A RCH R E S E T M E N U F O C US LE N S S H I FT Z O O M 7 Setting Up (co.
8 Setting Up (continued) Setting Up (continued) Connecting Y our Devices WARNING • Whenever attempting to connect other devices to the projector, read thoroughly the "User's Manual - Safety Guide", this manual and the manual of each device to be connected.
9 Setting Up (continued) Setting Up (continued) Please refer to the following (for example) for connecting your devices. See the rear of the projector.
10 Setting Up (continued) Setting Up (continued) VIDEO R-AUDIO IN-L S-VIDEO BNC RGB AUDI O IN1 AUDI O IN2 RGB OUT AUDI O OUT R/C R /P R G/Y B/C B /P B HV Y CONTROL NETWORK CR/PR Ca/Pa REMOTE CONTROL H.
I N T E R I N P U T M 1-D RG B B NG S-VID E O S TAN DBY / O N TEM P VI D E O COM P ONENT LAMP KEYST O N E SEARC H R E SE T M E N U F OC US L E N S SHIF T Z O O M VID EO R -A U D IO I N -L S-VIDE O BNC.
12 Remote Control Remote Control About The Laser Pointer Putting Batteries WARNING • The laser pointer of the remote control is used in place of a finger or rod. Never look directly into the laser beam outlet or point the laser beam at other people.
ST ANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOLUME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + ––– ++ FOCUS ZOOM 13 Remote Control (continued) Remote Control (continued) Operating The Remote Control CAUTION • Do not disassemble the remote control.
STANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOLUME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + ––– +.
STANDBY/ON VIDEO LASER INDICATOR RGB SC S LENS SHIFT + ––– ++ FOCUS ZOOM I N T E R I NP U T M 1-D R GB B N G S -V I D E O S T A N D BY / O N T E M P V ID EO C O M P O N E N T L A M P K E Y ST O .
I N T E R I N P U T M1-D R GB B N G S - V I D E O S T A N DB Y / O N T E M P V ID E O C O M P O N E N T LA M P K E Y S T O N E S EA R C H R E S E T M E N U F O CU S LE N S S H I F T Z O O M V ID E O R.
ST ANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOLUME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + ––– .
ST ANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOLUME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + ––– .
ST ANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOLUME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + ––– .
ST ANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOLUME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + ––– .
ST ANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOL UME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + –––.
STANDBY/ON VIDEO LASER INDICAT OR ESC MENU POSITION RESET AUTO KEYSTONE 1 2 3 ID CHANGE SEARCH ON OFF FREEZE MUTE MAGNFY PinP VOL UME RGB BLANK PREVIOUS NEXT ASPECT ENTER LASER LENS SHIFT + ––– .
23 Multifunctional Settings (continued) Multifunctional Settings (continued) MAIN Menu With the MAIN menu, the items shown in the table below can be performed.
24 PICTURE-1 Menu With the PICTURE-1 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
25 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description MY MEMORY Select a command to load or save using the / buttons, and then press the (or the ENTER) button to perform the function.: This projector has 4 numbered memories for adjustment data.
26 Multifunctional Settings (continued) Multifunctional Settings (continued) PICTURE-2 Menu With the PICTURE-2 menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. memo This menu cannot be selected at a M1-D signal.
27 Multifunctional Settings (continued) Multifunctional Settings (continued) INPUT Menu With the INPUT menu, the items shown in the table below can be performed.
28 Multifunctional Settings (continued) Multifunctional Settings (continued) INPUT Menu (continued) Item Description P.IN P. INPUT Select a signal input port for the child window using the / buttons. : VIDEO S-VIDEO memo About the child window, please refer to the section “Displaying the Child Window”.
29 Multifunctional Settings (continued) Multifunctional Settings (continued) AUTO Menu With the AUTO menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below. Item Description ADJUST Pressing the (or the ENTER) button performs the automatic adjustment.
30 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description SEARCH Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, detecting no signal cycles through input ports and displays the picture of retrieved signal.
31 Multifunctional Settings (continued) Multifunctional Settings (continued) SCREEN Menu With the SCREEN menu, the items shown in the table below can be performed.
32 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description MESSAGE Select the TURN ON or the TURN OFF using the / buttons. : TURN ON TURN OFF When the TURN ON is selected, the following message function works. The message of the “AUTO IN PROGRESS” for the auto adjustment.
33 Multifunctional Settings (continued) Multifunctional Settings (continued) OPTION Menu With the OPTION menu, the items shown in the table below can be performed.
34 Multifunctional Settings (continued) Multifunctional Settings (continued) Item Description SERVICE Pressing the (or the ENTER) button calls the SERVICE menu. SERVICE Menu Select an item using the / buttons, and press the (or the ENTER) button to per form each function.
35 Multifunctional Settings (continued) Multifunctional Settings (continued) NETWORK Menu This projector provides the NETWORK function. If you use this function, please set up the projector according to the Network environment in which you use it.
36 Network Setting Up Network Setting Up This projector provides the NETWORK function. If you use this function, please consult your dealer for information. To start, connect the NETWORK port to a gateway device via a RJ-45 (10BASE-1) cable, then set up the projector according to the Network environment in which you use it.
37 Lamp Lamp The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
38 Lamp (continued) Lamp (continued) After making sure that the projector has cooled adequately, slide the knob of a lamp cover lock as shown in the Figure. Then, one side of the lamp cover is raised. Pull up the lamp cover and remove it, as shown in the Figure.
39 Caring For The Air Filter Air Filter Air Filter WARNING • Please carefully read the “User’s Manual - Safety Guide. • Before caring, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool sufficiently.
40 Other Care Other Care WARNING • Please carefully read the “User’s Manual - Safety Guide”. • Before caring, make sure the power switch is off and the power cable is not plugged in. • Be cautious of high temperature. Do not touch about the lens and ventilation openings during use or immediately after use prevent a burn.
41 T T roubleshooting roubleshooting Related Messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below.
42 Related Messages (continued) T T roubleshooting (continued) roubleshooting (continued) Message Description CLEAN THE AIR FILTER POWER OFF FIRST, THEN CLEAN THE AIR FILTER. AFTER CLEANING THE AIR FILTER, RESET THE FILTER TIMER. The time the filter timer has counted has reached 100 hours.
43 T T roubleshooting (continued) roubleshooting (continued) Regarding The Indicator Lamps Lighting and flashing of the STANDBY/ON indicator, the LAMP indicator, and the TEMP indicator have the meanings as described in the table below. Please respond in accordance with the instructions within the table.
44 T T roubleshooting (continued) roubleshooting (continued) Regarding The Indicator Lamps (continued) STANDBY/ON indicator LAMP indicator TEMP indicator Description Lighting in Red Blinking in Red Turned off Either there is no lamp and/or lamp cover, or either of these has not been properly fixed.
45 T T roubleshooting (continued) roubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects WARNING • Never use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc.
46 T T roubleshooting (continued) roubleshooting (continued) Phenomena That May Easily Be Mistaken For Machine Defects (continued) Phenomenon Cases not involving a machine defect Reference pages Pictures are displayed, but no sounds are heard. The signal cables are not correctly connected.
47 If a problem occurs with the equipment, first refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied.
デバイスBOXLIGHT MP-58iの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
BOXLIGHT MP-58iをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBOXLIGHT MP-58iの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。BOXLIGHT MP-58iの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。BOXLIGHT MP-58iで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
BOXLIGHT MP-58iを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBOXLIGHT MP-58iの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、BOXLIGHT MP-58iに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBOXLIGHT MP-58iデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
