BrickcomメーカーFD-202Neの使用説明書/サービス説明書
ページ先へ移動 of 33
Hardware Use r ’ s Manua l Megapixel Day & Night Fixed Dome Network Camera Quality Service Grou p Fixed Dome Serie s.
Review Histor y: 1. Sep arate User Manual into HW and SW . 2. Merge FD-300Ap/ FD- 130N / FD -132N/ F D-300 A / FD-302A/ FD-500A/ FD -502A series into this User Manual.
T able of Conten Before Y ou Use This Product ....................................................................................... 1 Regulatory Information ............................................................................................
1 Before Y ou Use This Pr oduct In many countries, there are laws prohibiting or restricting the use of surveillance devices. This Network Camera is a high -performance, web-rea dy came ra which can be part of a flexible surveillance system.
2 Regulatory Informati on Federal Commu nication Commission I nterference State ment This e quipment has been tested and fo und to comply with the limits for a Class B d igital device, p ursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection ag ainst harmful interference in a residenti al installation.
3 Chapter 1 - Package Content s a. Netw ork Camera (Fixed Dome series) b. T erminal Block c. Product CD d. Loca tion Stick er e. W arranty Card f. Screw Bag g.
4 Chapter 2 - Fixed Dome Network Camera Overview The FIXED DOME SERIES is a full -featured, 3-axis, f ixed-dome, network camera. W ith a megapixel progressive sensor and built -in IR-cut filter/ IR illuminator LEDs/ Auto Light se nsor , it can provide 24 -hour , indoor surveillance.
5 Chapter 3 - Device App earance Description 1. Below “ Device A ppearance Description ” is for FD -20 0Np V6 / FD-202Ne V6 / FD -300Np St ar/ FD-302Ne S t ar/ FD-502 Ap V6 / FD-502 A e V6 2.
6 3. Below “ Device A ppearance Description ” is for FD-300Ap 4. Below “ Device A ppearance Description ” is for FD-501Af-series RJ45 Connector Reset Button T erminal Block (For Audio in/out, .
7 NOTE 1. SD Card Cap acity (*) - The network ca mera is compa tible with SD /SDHC/SDXC (Maximum 64 GB) cards. 2. (*) These are o ptional features. Please refer to the Product List fo r the full list of optional features available for the product.
8 Chapter 4 - LED Behavior Function LED Behavior Description Power LED Continuous illumination (Green) Power on Power LED Unit Power off Link LED Continuous illumination (Red) Link Link LED Blinking (.
9 < Hardware Reset > The Reset Button can be used to re boot the camera, restore it to factory default settings , or switch on FocusEasy . If the camera e xperiences a p roblem, rebooting the ca mera may correct the problem. If the problem remains, please restore the camera to factory default settings and reinstall the s oftw are.
10 Chapter 5 - Inst allati on 5.1 Hardw are Inst allation A. Remov e the dome cover from the camera device l. PoE, Power , DIDO, A udio Connection 1) Insert the PoE(1) / DC1 2V(2), DIDO and Audio cabl e(3) through con duit hole A o r B.
11 a. PoE, Power , DIDO, A udio Connection ii. Connect the PoE ( 1) / DC 12V (2), DIDO and Audio (3) Cables to their respective terminals. See the next page for more details regarding the DIDO and Audio connection. 1) Power over Ethernet (PoE) Connection 2) Power A dapter Connection Please refer to the definition of the terminal blocks below .
12 3) DIDO and A udio Connection Please refer to the definition of the terminal blocks below . It is also printed on the motherboard. Term inal Block Pin No. Function Pin 1 5V / 12V* Pin 2 D_0 Pin 3 D_I Pin 4 DIDO GND Pin 5 Audio OUT Pin 6 DGND Pin 7 Mic/Line in Pin 8 DGND *V5&V6 (W DRPro & S tar & S tarPlus) Series Supported ll.
13 3) Hammer the four plastic anchors which are provided in the product package into the tw o location holes. 4) Mount the camera on the wall and position to two screw slots over the plastic anchors. Insert the screams into the holes and use the screwdriver to tighten the screws clockwise until they are secure.
14 C. For ceiling install ation: The user needs the two screws which are included in the product p ackage and a screw driver . Moun t the c amera on th e desired location a nd use the screwdriver to tighten the screws clockwise through the two holes on each side of the device as shown below .
15 ii. Release the tilt screw on both side of the device and then rotate the lens to up or down. After completion, tighten the tilt screw. iii. Release th e video adjustment screw and then adjust the lens direction. After completion, tighten the video adjustment screw.
16 b. How to adjust the view angle and focus range i. Release the view angle controller and then moving the controller bar le ft or right to a djust the view angle. Af ter completion, tighten the view angle controller. ii. Release the focus controller and then moving the con troller bar left or right to adjust the focus ra nge.
17 5.2 Camera Connection F. Basic Connection (Withou t PoE) a. Connect the power adaptor to the camera dev ice. b. Connect the camera to the Ethernet hub using a RJ45 Ethernet cable. G. Power over Ethernet (PoE) Connection a. Connect the camera to a PoE-enabled hub via single Ethernet cable.
18 5.3 System Requirement s Operating System: Microsoft W indow s 8.1/8 /7/Vist a/XP/2000/ Computer: IBM PC/A T Compatible CPU: Pentium 3GHz or faster Memory: 1024 MB or more Monitor: 1024 x 768 pixel.
19 5.4 Sof t w are Inst allation In this m anual, "User" refers to whoever h as access to the Network Camera, and "Administrator" refers to the person who ca n configure the camera and grant user access to the camera.
20 B. In the Inst all Shield Wizard dialog box, click <Next> to continue. C. Read the End- User License Agreement and che ck the option “I accept the terms of the license agreement”.
21 D. Click <Change> to change the a ppointed folder w here inst allation and program files will be stored. Click <Next> to continue. E. Select to create shortcuts.
22 F. Select the application and click <Finish> . When launching the PC-NVR program, please refer to the PC-NVR user manual..
23 5.4.1 Eas y Config T o launch EasyConfig, select EasyConfig from the start menu. If Comp lete Setup type w as use d in the softw are installation, an EasyConfig icon was installed on the desktop.
24.
25 B. Select e ither “S imple M ode ” or “P rofessional M ode ” to obtain the camera’ s IP sett ings. If “S imple M ode ” is selected, EasyConfig will set u p the connection automatically . I f “P rofessional Mode ” is selected, the user will need to configure the IP settings manually .
26 C. There may be many cameras in the local network. Dif ferentiate the cameras using their UPnP name. Double click on the camera from the survey list to connect.
27 If <Set IP Address configuration manually> is selected, the following pages will be displayed..
28 E. If the camera support s the EasyLinkTM function , the following p age will be displayed. Ot herwise, this page w ill not be shown. *If desired, click <Skip> to skip this setting. EasyLinkTM is a unique Brickcom f unction which allo ws users to assign a unique EasyLink name to th eir network ca mera’ s IP address.
29 F. W hen the IP address settings have been configured , the screen will either display a successful or fa iled connection message. If the connection failed, either try again or quit the installation. a. If “ DHCP IP address settings” was selected, the failure page will be displayed as below: b.
30 c. If the connection was successfu l, the user will see the message: “Congratulations. The installation of the ca mera is complete.” W hen this window is displa yed, click <PC-NVR> to sta.
デバイスBrickcom FD-202Neの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Brickcom FD-202Neをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBrickcom FD-202Neの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Brickcom FD-202Neの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Brickcom FD-202Neで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Brickcom FD-202Neを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBrickcom FD-202Neの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Brickcom FD-202Neに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBrickcom FD-202Neデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。