Briggs & StrattonメーカーLT-200の使用説明書/サービス説明書
ページ先へ移動 of 14
1/2006 1 TP 300-4517-00-RG-SMAN Setup & Adjustment Instructions L T -200 Series T ractors and Mowers T ABLE OF CONTENTS: SAFETY RULES .................................................................2 SETUP PROCEDURES Quick Setup List ............
L T -200 Series TP 300-4517-00-RG-N 3/2007 2 Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of equipment, severe personal injury or death to you, yourself or bystanders, or damage to property or equipment.
L T -200 Series 3/2007 3 TP 300-4517-00-RG-N Quick Setup List - P age Setup Procedure Steps to P erform 4 Uncrating o Remov e Crate & Banding. o Place T ransmission Release Le ver in PUSH position & Roll T ractor f orward off skid.
L T -200 Series TP 300-4517-00-RG-N 3/2007 4 Uncrating Using a reciprocating utility saw or equivalent, cut crate away from bottom skid. Remove crate. Remove shrink- wrap plastic. 2. Cut banding from front and rear tractor axles. Cut banding from mower rollers.
L T -200 Series 3/2007 5 TP 300-4517-00-RG-N Chec k Fluid Levels Check T ransmission Oil Level The K46 transmission is a sealed unit that is shipped with the correct oil level. However if a transmission’s oil level is suspect it can be checked. See Transmission Maintenance.
L T -200 Series TP 300-4517-00-RG-N 3/2007 6 Figure 4. Seat Switch A. Seat Switch B. Wiring Harness P erf orm Safety Chec ks Functional T ests 1. Check the tractor for loose bolts, screws, nuts, etc.
L T -200 Series 3/2007 7 TP 300-4517-00-RG-N Figure 5. Blade Torque A. 4x4 Wood Block B. Spline or Hex Washer C. Spring Washer D. Blade Bolt T or que Mower Blades 1. Secure the hex washer (B, Figure 5), spring washer (C) and capscew (D). Use a wooden block (A) to prevent blade rotation while tightening the blade bolt (D) to 45-55 ft.
L T -200 Series TP 300-4517-00-RG-N 3/2007 8 Lubrication Lubricate the unit at the locations shown in Figures 7-10 as well as the lubrication points listed. Generally, all moving metal parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys.
L T -200 Series 3/2007 9 TP 300-4517-00-RG-N Figure 8. Mower Lubrication Points Figure 10. Arbor Lubrication Point Figure 9. Mower Lubrication Points Hourmeter HOURMETER MODELS The hour meter measures the number of hours the key has been in the RUN position.
L T -200 Series TP 300-4517-00-RG-N 3/2007 10 Mower Dec k Remov al & Installation Removing the Mo wer Deck 1. Park tractor on a hard, level surface such as a concrete floor. Turn off PTO switch and engine, remove the key and apply parking brake. 2.
L T -200 Series 3/2007 11 TP 300-4517-00-RG-N Leveling The Mo wer If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as specified in Checking Tire Pressure.
L T -200 Series TP 300-4517-00-RG-N 3/2007 12 Gauge Wheels The mower gauge wheels can be placed in several positions depending on the height of cut. When using higher cutting heights, set the wheels in the lower position. When using lower cutting heights, set the wheels in the upper position.
L T -200 Series 3/2007 13 TP 300-4517-00-RG-N Electric PT O Clutch Adjustment Check the PTO clutch adjustment after 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage.
L T -200 Series TP 300-4517-00-RG-N 3/2007 14 Mower Belt Replacement Note: It is not necessary to remove the mower to install a new belt. However, for easier access mower can be removed. See Mower Removal in the Operation section. 1. Park the tractor on a smooth, level surface such as a concrete floor.
デバイスBriggs & Stratton LT-200の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Briggs & Stratton LT-200をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBriggs & Stratton LT-200の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Briggs & Stratton LT-200の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Briggs & Stratton LT-200で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Briggs & Stratton LT-200を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBriggs & Stratton LT-200の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Briggs & Stratton LT-200に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBriggs & Stratton LT-200デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
