
Quick Start Guide
クイックスタートガイド


2. What’s in the box
Thank you for choosing REXING! We hope you love your new product as much as we do.


If you need assistance, or have any suggestions to improve it, please contact us. You can reach us via care@rexingusa.com or call us at (203) 800-4466. Our support team will respond you as soon as possible.
Always a surprise in Rexing. Check us out here.
https://www.facebook.com/rexingusa/ https://www.instagram.com/rexingdashcam/ https://www.rexingusa.com/support/registration/

Facebook Instagram Site

4. Installation


Place the 3M adhesive on the mount and properly orient the mount square to the roof and hood line of the vehicle. Important! Ensure the T-interlock on the Mount is oriented in the correct direction (as shown below).
Firmly press the mount onto the windshield. Wait at least 20 minutes before mounting the camera.
Orientation mount as shown


The Rexing V1 Basic accepts [Class 10/ UHS-1 or higher] Micro SD memory cards up to 256 GB. You will need to insert a memory card before you can begin recording. Before inserting or removing a memory card, first ensure you’ve powered down the device.
* The Camera is recording when the LED is flashing red.
** The Camera is recording when the LED is flashing red. The device charging or powered on when the LED is solid blue.
Gently push the memory card in until you hear a click, and allow the spring release to push the card out.
*** The device is charging or powered on when the LED is solid blue.

You may now disconnect from power. The camera will shut down after 3 seconds. The camera should begin recording automaticially the next time it is powered on.


Press the Power button to turn the power off
Press the Menu button twice
Power the camera by connecting the charger to the car cigarette lighter and camera.
To ensure the V1 Basic records to your memory card properly and without error. Before you start using a new memory card, you must format the card within the camera using the format function. Always backup important data stored on the memory card before formatting.
To format the memory card, make sure you have inserted your memory card, then turn on the device by connecting to a power source. Press REC to stop recording. Then press the MENU button twice to enter the System Setup Menu. Use the REC and MIC buttons and go to the Format setting. Press the OK Button to con irm the selection.
Press the OK button to confirm formatting the card

Place the camera on the mount and carefully route the power cable around the windscreen and tuck in under the trim.
The device is automatically powered on when plugged into a 12V accessory socket or cigarette lighter and receives a charge (i.e.: the vehicle is started.)
Plug the Car Charger Cable into a 12V DC power outlet or the car cigarette lighter.
Connect car charger to the camera. The camera will auto-start recording once powered on.
To turn the device on manually, press and hold the POWER button until the welcome screen appears.
The camera will autoatically start recording when powered on.


Plug Mini 5 pin Connector to the Dash Cam
Press an hold the POWER button to turn the device on manually
Route power cable to the Dash Cam
Plug charger into power outlet or cigarette lighter
Device Power


Power the camera on. If the camear is recording, pres the REC button to stop recording. Press the MODE button and toggle to the desired mode.
The camera will automatically start recording when the device receives a charge. The LED lights and the red dot will blink when the device is recording. Press the REC button to stop recording.
Press the MENU button once to enter the settings menu for a Mode. Press the MENU button twice to enter the System Settings.

The camera automatically start recording when powered on

Press the Menu button to
select the desired setting
Playback of videos can be done on the device or a computer. Also, if you have purchased a Rexing GPS Logger you may play back the recordings in a specialized application.
Press the Mode button and toggle to the desired Mode
Control playback with these buttons


To playback a video on the device, toggle to the Playback mode. Use the REC and MIC buttons to toggle to the desired video. Press the OK button to play.
To playback a video using USB to Mini B 5pin male cable, connect the USB to Mini B 5pin Male Cable to the device and the USB connector to the computer.
Connect USB connector to computer
During playback use the OK (pause), MIC (fast forward) and REC (rewind) buttons to control the video playback.
After the device powers up, press the OK Button to select Mass Storage. On the computer, navigate to device drive. The videos are stored at: \CARDV\ MOVIE.
To playback a video on the computer either use an SD card adapter or connect the device to the computer directly using the USB to Mini B 5pin male cable.

To playback a video using an SD card adapter, remove the memory card and insert it into an SD card adapter. Place the adapter in the computer.
Select the video to playback.
You can enable the parking monitor function through the setup option.
Select Mass Storage · Parking Monitor

GPS Logger (Need to purchase separately. ASIN: B07BL4NCMD)

Toggle to the Playback mode and select a photo to view

GPS Signal (not connected)
To take a photo, stop video recording and toggle to the Photo Mode.
When connected to the camera, it will record the speed and location of your vehicle as you drive.
Press the OK Button to take a photo.
To view a photo, stop video recording and toggle to the Playback Mode.
You can then access this information while playing back your recordings using the GPS Video player (For Windows and Mac, available at rexingusa.com).

Press the REC and MIC Buttons to toggle through your photos.
Toggle to the Delete option
Press the MENU button twice and enter the System Settings.
To delete a photo, stop video recording and toggle to the Playback Mode and toggle through the videos and photos to the one you want to delete.
Toggle to the GPS Speed Unit setting and select your preferred speed unit.
After a GPS signal is found, the screen icon will turn from blue to green.

Choose the desired option
Press the MENU button once and toggle to the Delete option.
Please visit gpsa.rexingusa.com to watch a video tutorial.
Press the OK Button and select Delete Current or Delete All.
Taking Photos · GPS Signal (searching) · GPS Signal (active)
この取扱説明書で参照されているリンク(メーカー、サポート、ダウンロード等)。
ユーザーまたはスタッフが通常1日以内に回答します。あなたの質問が次の人の助けにもなります。
最初の質問を投稿しましょう。他のユーザーや当チームが回答します。