BrotherメーカーLX-900の使用説明書/サービス説明書
ページ先へ移動 of 50
LC0075001 Printed in China/Imprimé en Chine 9906 ENGLISH/FRENCH ® Owner’s Manual.
- 0 - FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- 1 - Brother Cool Laminator LX-900 /LX-910D Fax-Back System Brother Customer Service has installed an easy-to-use Fax-Back System, so you can get instant answers to common technical questions and product information for all Brother products. This system is available 24 hours a day, 7 days a week.
- 2 - Ordering Accessories and Supplies (in the USA) For best quality results use only genuine Brother accessories, available at most Brother retailers. If you cannot find the accessory you need and you have a Visa, MasterCard, Discover, or American Express credit card, you can order accessories directly from Brother.
- 3 - Table of Contents Getting started ........................................................................................................................................................ 4 Features ...............................................
- 4 - Getting started Thank you for purchasing a Brother Cool Laminator. This machine has been designed to be easy to use, but can be utilized to its fullest potential by taking some time to read this owner’s manual.
- 5 - Precautions T o avoid personal injury or damage to the machine, please pay close attention to the CAUTION and WARNING notices in this manual. They are there for your safety , as well as to point out actions that might cause damage to your machine.
- 6 - Package list 1 Machine 1 2 Film cartridge 1 (Double side laminate type) 3 AC adapter 1 4 Owner’s manual 1 5 Compatible accessory list 1 6 Supplemental PC software (CD-ROM) 1 1 2 3 4 5 6.
- 7 - Part names Outside of the machine DC connector Located on the left, backside of the machine. Aperture for the AC adapter. Top cover For replacing the film cartridge and cutter units. Viewing window Located on the top cover. Allows you to make sure that the correct type of film cartridge is loaded into the machine.
- 8 - Control Panel POWER SWITCH On/ Off T urns the machine on/off. ( cut button) Cuts the document in the current position. Feed Use to feed the document manually. Start / Stop Use this button to start or stop an operation. The green LED indicates that the machine has power, and is turned on.
- 9 - Setup Installing the film cartridge (1) Open the top cover. (2) Push the roller release lever (green color) and lift the roller holder upwards. (3) Carefully i nstall the film cartridge , square end down. Match the arrow symbol to install new cartridge.
- 10 - (4) Return the roller holder to the original position and press the roller holder lock buttons (purple color) as illustrated. Y ou will hear the roller holder click into place . Press the roller holder further to secure the roller unit. (5) Close the top cover.
- 11 - (3) Press the power switch on the control panel to turn it on. The green S tart button will light up. If the machine does not respond, check the connection of the AC adapter. Press the power switch again to turn the machine off. WARNING: Do not plug your machine into an electrical outlet until it has been completely assembled.
- 12 - About film rolls There are a variety of different roll film types that have been designed to meet your needs. This machine supports 9.0 inch (A4) or 4.
- 13 - Replacing the film cartridge WARNING: Never touch the surface of the blades when installing/replacing the film cartridge. (1) T urn the power off and open the top cover. (2) Push the roller release lever (green color) and lift the roller holder upwards.
- 14 - (4) Install the new film cartridge carefully. (5) Return the roller holder to the original position and press the roller holder lock buttons (purple color) as illustrated. Y ou will hear the roller holder click into place . Press the roller holder further to secure the roller unit.
- 15 - Installing /replacing the film roll in the cartridge Cartridges can be recycled by replacing the film roll. Be sure to use Brother-authorized LC film refills only . R efill cartridge s using the following instructions: (1) Remove the film cartridge from the machine.
- 16 - (4) T ake the new roll of film from the sealed pack age . Holding the yellow colored plastic side holders of the film roll. Set the film into the cartridge as illustrated. The film can only be placed into the cartridge in the proper direction. (5) Close the film cartridge.
- 17 - (8) Check the position of the top edge of film. It should be aligned with the cutting line of the cartridge. If any film extends beyond the cutting line, cut away the access film as illustrated before installing the cartridge. (9) Install the cartridge into the machine.
- 18 - (12) T urn the power on. Press the F eed button until you can see the edge of the film to remove any slack from the film. CAUTION: T o prevent the film from drying out, never open the sealed pack until you are ready to install the cartridge.
- 19 - D ocument Size The size of the document that you wish to laminate should not be larger (or smaller) than the width that your machine can accommodate. The document should be between 2.2 and 8.5 inches (55 and 216mm) wide and between 3.54 and 39.
- 20 - Operating the machine Laminate documents, Create magnetic signs, and laminate with adhesive back: (1) Open the document supporter. (2) Load the document to be laminated onto the document tray.
- 21 - (5) Press Start . The document is fed into the machine. The machine will automatically start to detect the top and side edges of the document. The green light of the S tart button will blink during the finishing process . The top edge of the film will automatically be cut off when the Cut Mode is selected.
- 22 - How to define the cutting position (creating border s) The Auto Cross Cutting System automatically detects the size of your document and cuts each edge. The cutting position can be adjusted to create a margin on each edge of the laminated document .
- 23 - Manual feeding and manual cutting Y ou can feed and cut the document manually using the Cool Laminator. (1) Set the document on the document tray. (2) Press “ Feed” to feed the document manually. The “ Feed” button is a self-repeating key.
- 24 - Corner cutting After laminating, you can trim each corner of the document. (1) Insert a corner of the document into the corner-cutter slot. (2) The machine will automatically trim the corner of the document. (3) Remove the document from the slot.
- 25 - Corner cutter dust box The trimmings from the corner cutter are collected in the corner cutter dust box located just below the corner cutter slot. Pull the dust box towards you to discard the trimmings and set the box back into its original position.
- 26 - Regular maintenance and troubleshooting Y ou can keep your machine in optimum condition by cleaning it on a regular basis. Regular maintenance Avoid small debris and objects Be careful not to let anything slip into the machine, especially metal objects such as paper clips and staples.
- 27 - (4) Remove the film cartridge from the machine. (5) Remove the document from the film slit of the cartridge. (6) R emove any excess laminating film by cutting along the engraved “ cutting line ” on the cartridge before reinserting the cartridge.
- 28 - (8) Return the roller holder lock button (purple color) to its original position until it clicks into place. (9) Close the top cover. (10) T urn the power on. Press Feed button until you can see the edge of the film to remove any slack from the film.
- 29 - Replacing the side cutter units Cutter performance will decline as blades are dulled through use or become coated with adhesives. Use the following operation to replace the side cutter units. CAUTION: Do not touch the surface of the blade when replacing the cutter units.
- 30 - (5) Slide the old side cutter to the center . Remove the side cutter. (6) Slide the new side cutter to secure it in the side cutter holder. (7) Lift the tab to lock the side cutter into place . (8) Return the roller holder lock button (purple color) to its original position.
- 31 - (9) Close the top cover. (10) T urn the power on. Press Feed button until you can see the edge of the film to remove any slack from the film. Replacing the corner cutter tray The cutter performance will decline as blades are dulled. Y ou can improve it by changing the corner cutter tray.
- 32 - Troubleshooting Problem Cause Solution The AC adapter is not connected properly. Check that the machine is plugged into a power source. No activity after the machine has been turned on. The top cover is not completely closed. Close the top cover.
- 33 - Specification s Model number: LX-900 /LX-910D Processing method: Cold pressure method Power supply: AC adapt er (included) USA 120V ± 10% (60Hz) Output DC 18V 700mA Min./max. width of document: 2.17 ” – 8.50 ” (55mm – 216mm) Min./max. length of document: 3.
- 34 - Index A AC adapter ......................................... 6,10,11,32 Adhesive back laminate film ............................ 21 Adhesive sticker ............................................. 12 Alert buzzer .................................
- 35 - S Setup ............................................................... 9 Shutter ....................................... 8,9,14,15,16,27 Shutter button ......................................... 8,16,27 Side cutter .............................
- 36 - Appendix (About PrintMaster Gold Software) Mindscape and PrintMaster are registered trademarks and the Mindscape logo is a trademark of The Learning Company. Adobe and Acrobat are trademarks of Adobe system Incorporated. Windows is a registered trademark of Microsoft corp.
- 37 - FRANCE SUPPORT TECHNIQUE EN FRANCE Concours, Astuces, Solutions et Support T echnique 24h/24 7J/7 014069670 * 3615 EIDOS * (2F23 la minute) www.eidos-France.fr Logiciel distribué en France par Eidos Interactive, 6 Boulevard du Général Leclerc, 92115 Clichy Cedex ∗ Les frais d’appel seront à votre charge.
- 38 - Getting Started Before installing, check the system requirements listed below to make sure your computer is able to work with PrintMaster Gold. System Requirements PrintMaster Gold performs on any computer with the following features: • IBM PC with a 486DX2 66 MHz (or higher) • Windows 95, Windows 98, Windows 3.
- 39 - Installing PrintMaster Gold 1. Click the Install button or press ENTER to continue the installation. The PrintMaster Gold Installation screen appears with the default drive and directory, which you may change or accept as shown. 2. Click Continue or press ENTER to install PrintMaster Gold into the default directory, C:PMW.
- 40 - Reinstalling PrintMaster Gold Though unlikely, PrintMaster Gold files may become corrupted and the program may not run properly. If so, you can reinstall PrintMaster Gold, which cleans out all old files and restores original functionality. In Windows 95/98 1.
- 41 - Viewing/Printing PrintMaster Gold user's manual The full contents of user's manual is stored in the PrintMaster Gold CD-ROM. Please install the Adobe Acrobat Reader to see the online manual. How to install the Adobe Acrobat Reader 1. Double click the file Ar32e301 in the Acrobat 3 folder on the CD-ROM.
- 42 - The World of PrintMaster Gold This section introduces you to the PrintMaster Gold environment. As soon as you open the program, you'll notice PrintMaster Gold has several interrelated areas, each with it's own individual purpose and look.
- 43 - The workspace The Workspace is your own personal drafting board, with all the text, drawing, and editing tools you'll need to make a beautiful project. Here, you can put the finishing touches on your project, add new pictures, type in your personal message, and print.
.
- 45 - Add Toolbar The Add toolbar holds all the tools you need to add graphics, sentiments, and your own art to your project. T o hide or display the Add toolbar, access the View menu, the Toolbar/Add Bar . Add a picture Click here to go to the PrintMaster Art Gallery.
- 46 - Modify Toolbar Use the Modify toolbar to make adjustments to your art and text. With these tools, you can easily change the color of text and pictures, change line widths, add shadows, and crop pictures. T o hide or display the Modify toolbar, access the View menu, then Toolbars/Modify Bar .
- 47 - Status bar The Status toolbar is displayed at the bottom of the PrintMaster Gold window. Use this area to change your view of your project or to check the accuracy of your measurements. T o hide or display the Status toolbar, access the View menu, then Toolbars/Status Bar .
LC007 4 001 Printed in China 9906 ENGLISH ® Owner’s Manual Guide d’utilisation.
デバイスBrother LX-900の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Brother LX-900をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBrother LX-900の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Brother LX-900の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Brother LX-900で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Brother LX-900を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBrother LX-900の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Brother LX-900に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBrother LX-900デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
