Bryantメーカー362AANの使用説明書/サービス説明書
ページ先へ移動 of 12
NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. Index Page SAFETY CONSIDERATIONS ..................................................1-2 Minimum Clearance to Combustibles .
Only the latest issues of above codes should be used, and are available from either The National Fire Protection Agency, Bat- terymarch Park, Quincy, MA 02269 or The Canadian Standards Association, 178 Rexdale Blvd., Rexdale, Ontario M9W 1R3 Recognize safety information.
3. Caulking or sealants are applied to areas such as joints around window and door frames; between sole plates and floors; between wall-ceiling joints; between wall panels; at penetrations for plumbing, electrical, and fuel lines; and at other openings.
VENTING INSTRUCTIONS Venting of furnace should be to the outside and in accordance with local codes or requirements of local utility. OIL-FIRED APPLIANCES SHALL BE CONNECTED TO FLUES HAVING SUFFICIENT DRAFT AT ALL TIMES TO ENSURE SAFE AND PROPER OPERATION OF APPLIANCE.
ELECTRICAL The appliance must be installed in accordance with current ANSI/NFPA 70 National Electrical Code, CSA C22.1 Canadian Electrical Code Part 1, and/or local codes. The control system depends on correct polarity of power supply. Connect HOT wire (H) and NEUTRAL wire (N) as shown in Fig.
c. Tighten purge fitting. Allow oil to run to nozzle and fire burner. d. If purging takes longer than 30 sec and no flame has been established, burner stops. Push reset button on top of primary control to restart burner. e. For detailed information on operation of primary control, refer to instructions included with furnace.
The procedure for nozzle installation and/or replacement is out- lined in oil burner instruction manual which came with furnace. For ease of maintenance, the oiling procedure for burner motor, as outlined in burner manual, should be performed at this time.
17. Use a stiff brush and vacuum cleaner to clean inside of primary drum. CAUTION: Never use incendiary type cleaners (smoke sticks) for cleaning! WARNING: For all heat exchanger plates that have been removed, the gaskets MUST be replaced.
INSULATION INTERMEDIATE PANEL FILTER B A G D ELECTRICAL CONNECTIONS OIL INLET F 12 1 ⁄ 16 ″ EH 1 ″ INSULATION PARTITION PANEL SUPPLY DUCT CLEAN-OUT PORTS RETURN DUCT 1 ″ 3 ″ C A96309 DIMENSIONS (IN.
Fig. 6—Barometric Damper Locations A95117 FIG. A FIG. G FIG. D FIG. L FIG. B FIG. C FIG. J FIG. H FIG. K POOR WRONG WRONG WRONG WRONG WRONG BAROMETRIC DAMPER LOCATIONS GOOD LOCATIONS BAD LOCATIONS .
→ Fig. 7—Wiring Diagram A96380 INDOOR BLOWER MOTOR BR BR CAP T GND LINE V 24 V LINE V 24 V BK BL BR GR OR RD RD/BK VI WH YL F T CAP AL L.
USER’S INFORMATION I. HERE’S HOW YOUR HEATING SYSTEM WORKS The furnace operates automatically. It is controlled by a thermostat which you set at the temperature most comfortable to you. When the inside temperature drops below this setting, your thermostat will turn on heating system.
デバイスBryant 362AANの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bryant 362AANをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBryant 362AANの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bryant 362AANの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bryant 362AANで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bryant 362AANを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBryant 362AANの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bryant 362AANに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBryant 362AANデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。