Buffalo TechnologyメーカーWLI2-PCI-G54Sの使用説明書/サービス説明書
ページ先へ移動 of 45
User Manual 125* High Speed Mode™ Wireless PCI Adapter WLI2-PCI-G54S w w w .buffalotech. com/ wireless v2.3.
2 • Insert the AirNavigator CD into the CD-ROM drive of your computer. The AirNavigator Setup Wizard should launch automatically. • To launch the AirNavigator Setup Wizard manually, click Start , then Run . Type “ D: Setup.exe ”, where D is the drive letter assigned to your CDrom.
3 • Select Install Wireless Drivers . Installing Wireless Drivers.
4 • Click Next to install a driver for the PCI adaptor. • Select Agree and click Next to continue the process after reviewing the license agreemennt. • A window will appear prompting the installation of the Wireless PCI Adapter into the PC. You will need to shut down your PC to install the wireless PCI card.
5 • Power off the desktop PC. Insert the W ireless PCI Adapter into an available PCI slot. PCI slots are located inside the desktop computer . Please consult the PC Manufacturer's documentation for PCI installation instructions.
6 • When the ‘Found New Hardware Wizard’ launches, click Next . • If the ‘Digital Signature Not Found’ page opens, click Yes . • When the Wireless PCI Adapter is successfully installed, click Finish .
7 Connecting Wireless Clients to your Network Buffalo supports three different methods for connecting your wireless client device to your network. If your AP supports it, use the simple, utterly secure AOSS to connect. Install the Client Manager from your AirNavigator CD (page 8) and turn to page 11.
8 Client Manager can be used to survey and connect to available access points, congure WPA/WEP encryption, and create connection proles. Note: When Client Manager is installed, Windows XP Wireless Zero Conguration is automatically disabled. Installing Client Manager Insert the AirNavigator CD into the CD- ROM drive of you computer.
9 Client Manager • Once the Client Manager Installer launches, click Next . • Press Agree to accept the license agreement and continue installation.
10 Client Manager • Click OK when Client Manager installation is complete. • Press Exit Setup to exit AirNavigator. • Client Manager is now installed and running.
1 1 The AOSS button for this wireless client is in its Client Manager software. Start Client Manager by right clicking on the black antenna icon in your System Tray, or by launching the Client Manager from your Start Menu: Programs >> Buffalo >>AirStation Utility >> Client Manager.
12 • From the Status Screen, select the Proles tab. • Initiate AOSS by clicking the blue AOSS button on the Client Manager’s screen. The AOSS wizard will appear. • Now, press the AOSS button on the Access Point. Hold it down until the AOSS LED begins to ash.
13 Once AOSS is complete (about 30 seconds), the connection is archived as a prole for later use. To minimize Client Manager to the system tray, click the ‘X’ in the top right corner. Notes: AOSS will scan for an AOSS partner for about two minutes.
14 You may use Client Manager to congure your wireless network. Client Manager consists of the Status page, the Survey page, and the Proles page. You can access each page by clicking the corresponding button on Client Manager. In addition to these pages, several dialog boxes are also available.
15 Client Manager Configuration • Network Type - Displays whether network is in Ad-Hoc or Infrastructure mode. • Rate – The speed of communication between wireless devices. If the Client Manager is not connected to a remote wireless device (access point or another client), no rate will be displayed.
16 Click the Scan tab to open this page. Here, you can survey the area, display available access points, and connect to available access points. This page includes the following components: • Wireless SSID – The SSID is the “name” of a wireless network.
17 This dialog will open for you to enter any necessary encryption information. The correct encryption type should already be selected automatically in the Encryption Method drop down list. Only change this setting if necessary. The Encryption Key is where the actual key for the wireless network should be entered.
18 Profiles Page Click the Proles tab to open this page. Use this page to access your proles. Proles allow you to save the information associated with a specic wireless network so you can quickly and easily connect to that network when you are in that location.
19 New Profile Dialog Box • Select Profile – Select whether the prole is for a wireless or wired connection. • Profile Name – Enter the name you want to associate with the new prole. • Network Type – Select the network mode you want to associate with the new prole.
20 Advanced Profile Options • Network Tab – Displays the network information tab. A static IP can be specied for this wireless prole here. It is not recommended to change any of these settings unless specied by an administrator. • Browser Tab – Displays settings to change your browser preferences for this wireless prole.
21 Wi nd ow s XP in cl ud es th e Ze ro C on gu ra ti on Se rv ic e, a bu il t in se rr vi ce t o c on g ur e you r wi re le ss cl ie nt s fro m wi th in W ind ow s. Tu rn to p ag e 7 i f yo u wo uld r at he r use Bu ff al o’ s C li en t Ma nag er t o co ng ur e yo ur wi re le ss c lie nt .
22 • Click the Advanced tab to enter an SSID network name or WEP/WPA encryption key if necessary. To add an SSID network name that is not listed, click Add .
23 • To congure a WEP/WPA encryption key, select the wireless network and click Congure . • From the pull down menu, select the Network Authentication and Data Encryption types for the wireless network. Enter and conrm the Network Key and Key Index.
24 Installation with Windows 98/Me • After powering off the PC, insert the Wireless PCI Adapter into an available PCI slot. PCI slots are located inside the desktop computer . Please consult the PC Manufacturer's documentation for PCI installation instructions.
25 • Insert the AirNavigator CD . Click Next at the Welcome to the Found New Hardware Wizard . Select Search for a suitable driver for my device. Click the Next button to continue. • Select only the CD-ROM drives checkbox , and clear any other checkboxes that are selected.
26 • Windows will display a driver you can use with the Wireless Desktop PCI Adapter . Click the Next button to continue. • Windows 2000: If the Digital Signature Not Found page opens, informing that no digital signature exists for the driver you are installing, click the Y es button to continue the installation process.
27 Antenna Information • The WLI2-PCI-G54S comes with a detachable omni directional antenna. However , for increased range a more powerful antenna can be purchased. Use the included antenna adapter (small brass piece) to connect it to an optional Buffalo MC Connector antenna.
28 Wireless Zero Conguration Wireless Zero Conguration Service (Windows XP) Windows XP of fers the Wireless Zero Conguration Service to support 802.1 1b and 802.1 1g wire - less networking. This service automatically polls the area for available wireless access points.
29 Specications Wireless LAN Interface Standards Compliance IEEE 802.1 1g Communication Protocol Direct Sequence Spread Spectrum (DS-SS), Half Duplex Frequency Range 2.
30 Specications Communication Range Speed Indoor Outdoor 54Mbps 165 ft. (50m) 525 ft. (160m) 1 1Mbps 300 ft. (90m) 1310 ft. (400m) 1Mbps 375 ft. (1 15m) 1750 ft. (550m) All dis tan ces are esti mat ed. Wir eles s co nne ctio ns m ay b e a ffe cted as phy sica l co ndit ion s an d ci rcum sta nces var y .
31 T roubleshooting / F AQ T roubleshooting / F AQ Use this section to locate answers to frequently asked questions. What should I do if I already have a version of Client Manager on my PC? Update your Client Manager to the version on the CD.
32 T roubleshooting / F AQ Where can I attach my external antenna? Insert your external antenna into the antenna connector , located on the back of the G54 Wireless PCI Adapter . Why won't Client Manager function properly? Windows XP – The Wireless Zero Conguration Service conicts with Client Manager .
33 10BaseT or 100BaseTx: 802.3 based Ether - net network that uses UTP (Unshielded twisted pair) cable and a star topology . 10 is 10 Mbps and 100 is 100 Mbps. 802.1x: The standard for wireless LAN authenti- cation used between an AP and a client. 802.
34 Driver: Software that interfaces a computer with a specic hardware device. DSSS (Direct Sequence Spread Spectrum): Method of spreading a wireless signal into wide frequency bandwidth. DTE (Data T erminal Equipment): Device that con10BaseT or 100BaseTx: 802.
35 nected to it, and retrieves the address when the device becomes dormant for a period of time. DNS (Domain Name System): System used to map readable machine names into IP ad- dresses Driver: Software that interfaces a computer with a specic hardware device.
36 LED (Light Emitting Diode): The lights on a hardware device representing the activity through the ports. MAC (Medium Access Control) Address: A unique number that distinguishes network cards. Mbps (Mega Bits Per Second): A measure- ment of millions of bits per second.
37 NA T (Network Address T ranslation): An inter- net standard that enables a LAN to use one set of IP addresses for internal trafc and a second set for external trafc. NIC (Network Interface Card): An expansion card connected to a computer so the computer can be connected to a network.
38 devices, allowing the network to be extended to accommodate additional workstations. RC4: The encryption algorithm that is used in WEP . RJ-45 connector: An 8-pin connector used between a twisted pair cable and a data trans- mission device. ROM (Read Only Memory): Permanent memory .
39 Uses UDP (User Datagram Protocol), rather than TCP/IP for data transport and provides no security features. TKIP (T emporal Key Integrity Protocol): An encryption method replacing WEP . TKIP uses random IV and frequent key exchanges. T opology: The shape of a LAN (Local Area Network) or other communications system.
40 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
41 IMPORT ANT NOTE: FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body .
42 EU Countries intended for use The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland, France (with Frequency channel restrictions), Germany , Greece, Iceland, Ireland, Italy , Luxembourg, Norway , The Netherlands, Portugal, Spain, Sweden, Switzerland and United Kingdom.
43 W arranty Information Buffalo T echnology (USA), Inc. products comes with a two-year limited warranty from the date of pur- chase. Buffalo T echnology (USA), Inc. warrants to the original purchaser the product; good operating condition for the warranty period.
44 Contact Information ADDRESS Buffalo T echnology (USA), Inc. 4030 West Braker Lane, Suite 120 Austin, TX 78759-5319 GENERAL INQUIRIES Monday through Friday 8:30am-5:30pm CST Direct: 512-794-8533 T oll-free: 800-456-9799 Fax: 512-794-8520 Email: sales@buffalotech.
45 T echnical Support is available 24 hours a day , 7 days a week (USA / Canada) T oll-Free: 866-752-6210 email: info@buffalotech.com ©2004, Buffalo T echnology (USA), Inc.
デバイスBuffalo Technology WLI2-PCI-G54Sの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Buffalo Technology WLI2-PCI-G54Sをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBuffalo Technology WLI2-PCI-G54Sの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Buffalo Technology WLI2-PCI-G54Sの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Buffalo Technology WLI2-PCI-G54Sで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Buffalo Technology WLI2-PCI-G54Sを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBuffalo Technology WLI2-PCI-G54Sの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Buffalo Technology WLI2-PCI-G54Sに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBuffalo Technology WLI2-PCI-G54Sデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
