Buhlerメーカー2895の使用説明書/サービス説明書
ページ先へ移動 of 46
.
WARRANTY REGISTRATION AND POLICY Buhler Manufacturing products are warranted for a period of twelve (12) months from original date of purchase, by original purchaser, to be free from defects in material and workmanship under correct, normal agricultural use and proper applications.
bühler Allied Front-End Loader - 1 - P4110 2895 OPERATOR’S AND PARTS MANUAL Table of Contents D e s c r i p t i o n P a g e Registration and Policy Loader Specifications ..............................................................................
bühler Allied Front-End Loader - 2 - P4110 LOADER SPECIFICATIONS Illustration (TSL shown).
bühler Allied Front-End Loader - 3 - P4110 2895 2895 Item Description REG TSL 2895S REG 2895S TSL A Maximum lift height to pivot pin [in/cm] 181/460 181/460 169/429 169/429 B Maximum lift height unde.
bühler Allied Front-End Loader INTRODUCTION This manual has been provided as information regarding the specifications, safe operation and maintenance of your agricultural front-end loader. Read and understand this manual and the tractor manual prior to operating to obtain the best use of operating your loader.
bühler Allied Front-End Loader Some components are identified as “right” and “left”. This is determined as seated in the tractor and facing forward, loader end. Serial Decal Location: The serial decal is located on the inside left arm of the loader joint plate.
bühler Allied Front-End Loader SAFETY Read and understand all the safety messages listed in this manual. For your safety and the safety of others near the machine, learn how to control and operate the loader properly. It is your responsibility to inform subsequent operators and owners of these precautions.
bühler Allied Front-End Loader Safety Decals: Safety Decal Location illustrates the approximate location and detail of safety decals. To install safety decals ensure the installation area is clean and dry. Decide on the exact position before you remove the backing paper.
bühler Allied Front-End Loader Safety Decal Location - 8 - P4110.
bühler Allied Front-End Loader The following pictorials indicate important precautions to be used during the operation of the loader. - 9 - P4110 WARNING WARNING WARNING FALLING HAZARD To prevent se rious inj ury or deat h: Do not lift, carry or al low anyone to ride on or work fr om any portion of loader.
bühler Allied Front-End Loader PRE – OPERATION WARNING The tractor must be equipped with an approved Roll over Protection Structure (ROPS) and safety belts to help prevent personal injury or death caused by tractor roll over. CAUTION Maximum rated loader capacity may exceed tractor rating.
bühler Allied Front-End Loader OPERATION General Operating Notes: The following section provides general information that can be applied towards your specific application. Ensure that you’ve read and understood this manual and your Tractor Manual .
bühler Allied Front-End Loader All Buhler - Allied hydr aulic valves are self-centering and return to neutral from all positions except float. The float or detent spool is only to be used on the boom circuit. This position allows the oil to freely flow through the valve so the lift cylinders can extend or retract.
bühler Allied Front-End Loader Minimize turning angle and length of run Carry the load no between pile and trailer to increase loading efficiency. Also, place load evenly or centered in the attachment. WARNING rt o highe than necessary clear the terrain.
bühler Allied Front-End Loader or back grading, either load the bucket and position must be used to – Frame: Standard and Heavy Duty A – Frames can be fitted with either Standard Duty uty frame i.
bühler Allied Front-End Loader andling bales and pallets: or safe handling of bales and pallets please follow procedures below: H F WARNING Do not operate A – Frame for bales without the stabilizers.
bühler Allied Front-End Loader When loading bales onto a trailer, park trailer s you lift the bale using the regular loader, it in close proximity to minimize turning angle and length of travel to increase loading efficiency. A is recommended to feather the valve to allow bucket cylinders to extend to keep bale at about a 20 q angle.
bühler Allied Front-End Loader pictorial below for options listed) Grapple: The grapple is designed to safely prevent loads (bales, silage) from falling out of the bucket. (Refer to WARNING Trave at low speeds. Carry loads as low as possible. Avoid sharp turns and uneven terrain.
bühler Allied Front-End Loader INSTALLING / REMOVING LOADER Installing: CAUTION Prior to initial mounting, cycle loader cylinders to displace air. This ensures the loader will remain in the storage position and operate consistently. 1. Position the tractor centrally and parallel to the loader uprights.
bühler Allied Front-End Loader 5. With the tractor in neutral, continue to retract the lift cylinders and extend the bucket cylinders to rotate the upright back against the lock pin stops. Shut the tractor off and set park brake. 6. Install both upright attachment pins and secure with hairpin clip.
bühler Allied Front-End Loader 2. Lower attachment level to the ground while engaging float position. Ensure attachment rests firmly on ground with minimal downward pressure. If required extend bucket cylinders to rotate upright rearward. At this stage the pin should have no pressure.
bühler Allied Front-End Loader INSTALLING / REMOVING LOADER ATTACHMENTS Installing: 1. Position tractor centrally within the bucket hooks. Dump Quick-tach slightly from vertical position. Slowly drive the tractor forward until the Quick-tach contacts the bucket.
bühler Allied Front-End Loader - 22 - P4410 LUBRICATION Lubricate loader bushings and pivots every eight hours of average operation with high-grade grease. For grease fitting locations see illustration below. Select grease based on the expected outside temperature range.
bühler Allied Front-End Loader - 23 - P4410 MAINTENANCE General Inspection: CAUTION Lower attachment and loader to ground, place all controls in neutral, stop engine, set parking brake and remove ignition key before inspecting, servicing, adjusting or repairing loader.
bühler Allied Front-End Loader - 24 - P4410 Mounting Kit: After the initial 2 weeks or 40 hours of loader operation, and 6-month intervals thereafter re-torque all mounting kit bolts. (See below for proper bolt torques) Bolt Torque Chart: Standard Metri c ft-lbs NM ft-lbs NM ft-lbs NM ft-lbs NM ft-lbs NM ft-l bs NM ft-lbs NM 0.
bühler Allied Front-End Loader - 25 - P4410 Hydraulics: WARNING Escaping fluid under pressure can have sufficient force to penetrate the skin, causing serious personal injury. Before repairing, adjusting, or disconnecting lines, be sure to relieve all pressure.
bühler Allied Front-End Loader - 26 - P4410 A yearly inspection of the valve is recommended. However the maintenance intervals on the valve depends on the surrounding environment or if valve spools become stiff.
bühler Allied Front-End Loader - 27 - P4410 On valves fitted with joystick cables loosen off jam nut and cable sleeves to gain access to the valve spool. Clean all debris and any existing corrosion. Spray areas with a light corrosion resistant lubricant.
bühler Allied Front-End Loader - 28 - P4410 TSL GENERAL NOTE AND INSTRUCTIONS 1. The true self leveling system (TSL) utilizes mechanical linkages to maintain bucket level while raising and lowering.
bühler Allied Front-End Loader - 29 - P4410 TROUBLE SHOOTING Possible Cause Quick couplers leaking Hydraulic oil too heavy. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaking. Control valve does not shift properly. Air in hydraulic system.
bühler Allied Front-End Loader - 30 - P4410 Trouble Shooting Continued Problem Insufficient lift capacity. Slow leak down. Excessive wear on bottom of bucket and wear pads. Hydraulic cylinders inoperative. Pump operating continually on closed center tractor hydraulics system.
bühler Allied Front-End Loader - 31 - P4110 2895 – 2895 S PARTS APPENDIX Description Page 2895-2895 S Main Frame Asse mbly ............................................................................... 32 Hydraulic Plumbing .......................
bühler Allied Front-End Loader - 32 - P4110 2895 – 2895 S Main Frame Assembly 28 32 31 33 19 16 25 26 35 27 34 14 29 30.
bühler Allied Front-End Loader - 33 - P4110 2895 – 2895 S Main Frame Assembly Item Part No. Description 2895 2895 S 1 24966 2895 Main Frame Weldment 1 - 1 24944 2895 S Main Frame Weld ment - 1 2 25165 2895 Quick Attach Weldme nt 1 1 3 Ref. Lift Cylinder (see cylinder assembly) 2 2 4 Ref.
bühler Allied Front-End Loader - 34 - P4110 2895 – 2895 S Hydraulic Plumbing Assembly.
bühler Allied Front-End Loader - 35 - P4110 2895 – 2895 S Hydraulic Plumbing Assembly Item Part No. Description 2895 2895 S 1 Ref. Bucket Cylind er (See cylinder assembly for breakdown ) 2 2 2 Ref.
bühler Allied Front-End Loader - 36 - P4110 2895 TSL – 2895 S TSL Main Frame Assembly.
bühler Allied Front-End Loader - 37 - P4110 2895 TSL – 2895 S TSL Main Frame Assembly Item Part No. Description 2895 TSL 2895 S TSL 1 24967 2895 TSL Main Frame Weldment 1 - 1 24945 2895 S TSL Main Frame Weldment - 1 2 25165 2895 Quick Attach Weldment 1 1 3 Ref.
bühler Allied Front-End Loader - 38 - P4110 2895 TSL – 2895 S TSL Hydraulic Plumbing Assembly 4 3 15 13 7 B B A 12 VIEW A- A 3 4 9 10 11 14 6 17 13 16 5 2.
bühler Allied Front-End Loader - 39 - P4110 2895 TSL – 2895 S TSL Hydraulic Plumbing Assembly Item Part No. Description 2895 2895 S 1 Ref. Bucket Cylind er (See cylinder assembly for breakdown ) 2 2 2 Ref.
bühler Allied Front-End Loader - 40 - P4110 Possible Attachment Interference (S2895 and 2895 TSL) Regular loader linkage setup allows for maximum rollback. TSL loader linkage setup provides reduced rollback. Large attachments (such as the C2000 Grapple) may contact the S2895 or 2895 TSL pivot plate.
bühler Allied Front-End Loader - 41 - P4110 2895 Cylinder Assembly NOTES: 1. Bucket cylinder shown 2. All cylinder seals are contained in correspon ding seal kit. 3. Refer to page 44 for prevailing torque for locknut s. CAUTION Maximum pressure – 3000 psi Bucket Cylinders Lift Cylinders Regular & TSL Regular TSL Regular Short Diameter 3.
bühler Allied Front-End Loader - 42 - P4110 Hydraulic Fitting Torques: (ft-lbs) (NM) (ft-lbs) (NM) -04 7/16- 20 14-16 20-22 10-11 13-15 -05 1/2-20 18-20 24-27 13-15 18-20 -06 9/16- 18 24-26 33-35 17-.
.
Buhler Manufacturing “ a partnership” Customer Support: 1-888-524-1003 1260 Clarence Ave. Box 7300 Winnipeg, MB. R3C 4E8 Ph.: (204) 661-8711 Fax: (204) 654-2503 www.buhler.com Printed in Canada Allied Division 1201 Regent Ave. W. Box 1003 Winnipeg, MB R2C 3B2 Ph.
デバイスBuhler 2895の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Buhler 2895をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBuhler 2895の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Buhler 2895の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Buhler 2895で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Buhler 2895を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBuhler 2895の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Buhler 2895に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBuhler 2895デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。