BunnメーカーCTの使用説明書/サービス説明書
ページ先へ移動 of 17
C, CT , CWTF Series Including DV , APS/TC/TS, Single CW & T wins Supercedes Operating Manuals: 10690.####; 10737.####; 10841.0000; 28182.0000; 36102.
Page 2 41721 051910 BUNN-O-MA TIC COMMERCIAL PRODUCT W ARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years.
Page 3 41721 111308 USER NOTICES ........................................................................................................................................... 4 ELECTRICAL REQUIREMENTS ....................................................
Page 4 USER NOTICES Carefully read and follow all notices in this manual and on the equipment. All labels on the equipment should be kept in good condition. Replace any unreadable or damaged labels. #12364.0000 W ARNING ! Fill water tank before turning - on - thermostat or connecting appliance to power source.
Page 5 ELECTRICAL HOOK-UP CAUTION – Improper electrical installation will damage electronic components. 1. An electrician must provide electrical service as specified. 2. Using a voltmeter , check the voltage and color coding of each conductor at the electrical source.
Page 6 PLUMBING REQUIREMENTS-CURRENT SINGLES As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow pre- vention to comply with federal, state and local codes.
Page 7 1. Remove six screws securing rear utility cover (if equipped). FIG 7-1 2. Remove cap from the flared fitting on the bottom of the center tube assembly . 3. Flush the water line and securely attach it to the flare fitting on the center tube assembly .
Page 8 PLUMBING REQUIREMENTS-EARL Y SINGLES MODEL C: This model is completely portable and requires no attached plumbing. MODELS CT , CTF , CWT , CWT A, CWTB, CWTF , CWTF A & CWTFB, SINGLE CW &.
Page 9 P1241 TWINS TWINS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a 1 ⁄ 2 " or larger supply line. A shut-off valve should be installed in the line before the brewer .
Page 10 INITIAL SET -UP CAUTION - The brewer must be disconnected from the power source throughout the initial set-up, except when specified in the instructions. 1. Insert an empty funnel into the funnel rails. 2. Place an empty dispenser under the funnel.
Page 11 SET/LOCK SWITCH THERMOST A T KNOB FIG 11-1 LOCK SET -1000 213.8 101.0 200 93.3 -500 212.9 100.5 200 93.3 0 212.0 100.0 200 93.3 500 211.1 99.5 200 93.3 1000 210.2 99.0 200 93.3 1500 209.3 98.5 200 93.3 2000 208.4 98.0 200 93.3 2500 207.4 97.4 200 93.
Page 12 ON/LOWER SWITCH Placing the "ON/LOWER" switch in the "OFF" (lower) position stops brewing. Stopping a brew cycle after it has been started, will not stop the flow of water into the funnel until the tank siphons down to its proper level.
Page 13 MASTER ON/OFF SWITCH(S) The master ON/OFF switch disables power the entire brewer (including tank heaters). NOTE – TWINS with 2 power cords will have 2 power switches, (one left, one right). T ANK HEA TER ON/OFF SWITCH(S) The tank heater ON/OFF switch disables power to the tank heater circuits only .
Page 14 COFFEE BREWING 1. Insert a BUNN ® filter into the funnel. 2. Pour the fresh coffee into the filter and level the bed of grounds by gently shaking. 3. Slide the funnel into the funnel rails. 4. Place an empty dispenser beneath the funnel. 5.
Page 15 Clean Sprayhead Holes FIG 15-3 1. The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all surfaces on Bunn-O-Matic equipment. Use care when cleaning around the heater switch with a cloth, so as not to accidentally turn off the tank heater! 2.
Page 16 TROUBLESHOOTING A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic T echnical Ser vice Department.
Page 17 TROUBLESHOOTING (cont.) PROBLEM Spitting or excessive steaming Dripping from sprayhead Brew cycle starts when ON/ LOWER Switch is turned on. Weak beverage Dry coffee grounds remain in the funnel PROBABLE CAUSE 1. Lime Build-up 1. Syphon System Auxiliary brew start switch on TWINS inadvertently activated.
デバイスBunn CTの購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bunn CTをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBunn CTの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bunn CTの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bunn CTで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bunn CTを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBunn CTの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bunn CTに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBunn CTデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。