BunnメーカーJDF-2の使用説明書/サービス説明書
ページ先へ移動 of 22
INST ALLA TION & OPERA TING MANUAL JDF-2 BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www .
2 BUNN-O-MA TIC COMMERCIAL PRODUCT W ARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor. 2) Electronic circuit and/or control boards: parts and labor for 3 years.
3 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 00986.0002 33461.0001 ! W ARNING DO NO T O VERLOAD CIRCUIT .
4 PLUMBING REQUIREMENTS This dispenser must be connected to a COLD WATER system with operating pressure between 20 and 100 psi (138 and 690 kPa). This water source must be capable of producing a minimum flow rate of 3 fluid ounces (88.7 milliliters) per second.
5 number .]) BUNN-O-MA TIC does not recommend the use of saddle valves to install the dispenser . The size and shape of the hole(s) made in the supply line(s) by saddle valves may restrict water flow . Note- A water strainer (Bunn-O-Matic part number 23720.
6 LOADING Frozen Concentrates 1. Thaw the frozen concentrate in a refrigerated 35-40 degrees F (1.6-4.4 degrees C) environment for 36 to 48 hours before use. 2. Thoroughly mix the thawed concentrate by vigorously shaking the product container. 3. Open the dispenser door.
7 OPERA TING CONTROLS Refrigeration Switch The refrigeration switch is located on the top of the dispenser near the left rear corner. This switch controls power to the compressor and the condenser fan motor. Sanitize Switch The sanitize switch is located behind the drip tray in the lower left corner of the chassis.
8 OPERATING CONTROLS (cont.) FIG 5 Press and Hold Models A. Product Dispense Switch Pressing and holding switch will initiate product flow from the respective nozzle; releasing the switch will stop the flow. B. Hidden Switch These switches are used to access, change and exit the dispenser program mode.
9 DISPENSER USE Press and Hold Models (Refer to Fig 5) 1. Place a cup on the drip tray beneath the desired dispensing nozzle. 2. Press and hold the “Product Dispense” switch until the beverage reaches the desired level, then release. Portion Control Models (Refer to Fig 6) 1.
10 CLEANING & PREVENTIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The Bunn Juice Dispenser incorporates a rinse reminder feature which lights the rinse led on the front panel when it is time to rinse. See dip switch function list to activate this feature.
11 CLEANING (cont) 6. Select the dispense stations by pressing the “Dispense Switch” for that station. Use the “+/Stop Switch” for portion contol dispensers. The “REFILL” indicator will light and the beeper will sound for the dispense head selected.
12 Monthly: Clean Condenser Air Filter 1. Remove the condenser air filter located on the rear of the dispenser. 2. Using a water spray, clean the air filter. Annually: Replace Pump Tubing 1. Open dispenser door. 2. Remove all product containers and place them in a refrigerated (35-40 degrees F [1.
13 ADJUSTMENT & OPTIONAL SETTINGS SETTING THE MIX RATIO/BRIX Ratio Cup Method 1. Adjust the water flow as described in Water Flow Testing and Adjustment. 2. Remove the dispense nozzle from the appropriate dispense position. 3. Assemble, lubricate, and install the Flow Separator Assembly (BUNN-O-MATIC part number 32629.
14 W ater Flow T esting and Adjustment 1. Enter the “Pump Speed Programming” mode by simultaneously press- ing both “Hidden Switches” Fig 5 or Fig 6.
15 the “Product Dispense” (“+/STOP”) Switch is pressed, the motor speed is decreased by one step (5 RPM.) Note that each step is confirmed by a single flash of the appropriate “REFILL” indicator and a single tone from the beeper. 4. Repeat as necessary at the remaining dispense stations.
16 6. If the password is forgotten, it can be reset to “0” (dispenser lockout disabled) as follows: Note: The following procedure also clears the programming and service lockout password. a) Disconnect the dispenser from its power source. b) Place the “Refrigeration Switch” Fig 3, in the OFF (rearward) position.
17 3. To enter the password, proceed as follows: a) Press and hold either “Hidden Switch”. b) In a 5 second period, press and release the “Sanitize Switch” the password number of times. For example: If the password is set to 3, press and release the “Sanitize Switch” 3 times in the 5 second period.
18 Dispense Fault List “REFILL” indicator Beeper Fault 2 flashes 2 beeps Dispense station locked out. 3 flashes 3 beeps DISPENSE/RINSE sensing fault. 4 flashes 4 beeps DISPENSE/RINSE knob mis-positioned. 5 flashes 5 beeps Pump motor stalled/speed sensor inoperative.
19 Dip Switch Function List Dip Switch Controls Off On 1 “REFILL” indicator when “concentrate out” is detected. Inactive Active 2 Lockout dispense components when “concentrate out” is detected. Inactive Active ( Note ) 3 Number of positions that can dispense/rinse simultaneously.
20 COOLANT SCHEMA TIC DIAGRAM CONDENSER SUCTION A CCUMULA TOR COMPRESSOR EV APORA T OR PROCESS TUBE 33464.0000A 09/00 ©2000 Bunn-O-Matic Corporation FIL TER DR YER 35303 012703.
21 SCHEMA TIC WIRING DIAGRAM 35303 121203 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 LAMP ASSY.
22 SCHEMA TIC WIRING DIAGRAM 35303 121203 J3-1 J3-2 J1-1 J1-5 J1-10 C O N T R O L P C B O A R D J1-18 J7-1 J7-5 J7-10 J7-16 J8-1 J8-8 J6-1 J6-6 J6-12 LAMP ASSY.
デバイスBunn JDF-2の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bunn JDF-2をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBunn JDF-2の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bunn JDF-2の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bunn JDF-2で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bunn JDF-2を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBunn JDF-2の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bunn JDF-2に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBunn JDF-2デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
