BunnメーカーSLCA-7の使用説明書/サービス説明書
ページ先へ移動 of 24
SLCA-7 INST ALLA TION & OPERA TING MANU AL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have the lates.
2 39328.3 070913 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
3 INTRODUCTION This equipment dispenses hot beverages or soups on demand from powdered product. It is indoor use only on a sturdy counter or shelf. T ABLE OF CONTENTS Introduction .......................................................................
4 As directed in the International Plumbing Code of the International Code Council and the Food Code Manual of the Food and Drug Administration (FDA), this equipment must be installed with adequate backflow prevention to comply with federal, state and local codes.
5 INITIAL SET -UP 1. Apply the four non-skid pads from the parts box to the bottom of the legs. 2. Remove the drip tray assembly and drip tray bracket from the parts box. 3. Place a set of key holes in the drip tray bracket over the lower two screws in the panel below the hopper ac- cess door; push down gently and tighten screws.
6 OPERA TING CONTROLS AND INTERF ACE 1. Cup Size Buttons: Momentarily pushed to select beverage size to dispense. 2. Stop Button: Momentary pushed to stop dispensing. 3. Decaf Button: Momentarily pushed to select Decaffeinated coffee. 4. Dispense Buttons: Momentarily pushed to dispense selected beverage.
7 10 11 8 9 STOP MOCH A LA TTE ESPRESSO DECAF CAPPUCCINO MOCHA CAPPUCCINO HOT CHOCOL AT E BLACK COFFEE LA TTE SMALL LARGE 5 3 1 2 6 1 4 OPERA TING CONTROLS (Continued) 39328.
8 INST ALLING PUMP TUBING 1. Loosen the thumbscrews securing the tubing retainer plates to the pump bodies and set the retainer plates aside. 2. Depress the tension screws and remove them from the notch in the pump body , releasing the spring tension on the pump bands.
9 INITIAL FILL & HEA T 1. T urn on the water supply and connect the dispenser to the power sour ce. 2. Water will automatically flow into the tank to the proper level and then shut-off.
10 SLCA-7 PROGRAMMING LED DISPLA Y PROGRAM MODE DESCRIPTION Program Mode: Used to change or enter new set-up values. T o enter the Program Mode , Set the RUN/NIGHT/PROGRAM Switch to the PROGRAM position, the unit will display “__PPP” to indicate it is in the Program Mode.
11 PROGRAMMING (Continued) LED DISPLA Y PROGRAM MODE DESCRIPTION MENU (-) (+) 6 0 3 0 MENU (-) (+) 7 0 3 0 MENU (-) (+) 8 0 1 0 MENU (-) (+) 9 0 1 0 MENU (-) (+) 0 1 4 5 0 MENU (-) (+) 1 1 1 0 MENU (-) (+) 2 1 1 0 5.
12 PROGRAMMING (Continued) LED DISPLA Y PROGRAM MODE DESCRIPTION MENU (-) (+) 3 1 8 MENU (-) (+) 4 1 5 MENU (-) (+) 5 1 2 4 MENU (-) (+) 6 1 1 MENU (-) (+) 7 1 # MENU (-) (+) 8 1 0 4.
13 PRIMING THE CONCENTRA TE LINES 1. Open the dispenser door . 2. Select Prime on the Function Selector Switch and Run on the Mode Selector Switch. 3. Close the dispenser door .
14 DRAINING THE HOT WA TER T ANK CAUTION - The dispenser must be disconnected from the power source throughout these steps 1. Disconnect the dispenser from the power source. 2. Open front door and place Main Power Switch in the OFF position and let the water in the tank cool before draining.
15 CLEANING & PREVENT A TIVE MAINTENANCE General Cleaning and Sanitizing Procedures Note: The BUNN¨ SLCA-7 dispenser incorporates a “user select- able” rinse reminder feature, which flashes the LED’ s on the front panel when it is time to rinse.
16 Weekly: Parts W ashing and Sanitizing 39328.3 012113 14. When reassem- bling parts, be sure to align arrow on frother disk with flat on whipper mo- tor shaft, and rotate tab on whipper base clock wise to the vertical position to lock mixing cham- ber .
17 REPLACING THE PUMP TUBING The pumps and tubing used in the dispenser are designed to give maximum performance and long life. However , the tubes are a wear item and must be replaced periodically . How long the tube last is dependent on usage and properties of the concentrate.
18 MENU (-) (+) CALIBRA TING THE DISPENSER CALIBRA TION MODE: The SLCA-7 is calibrated at the factory and does not normally need to be re-calibrated. T o enter the Calibration Mode , Set the RUN/NIGHT/PROGRAM Switch to the PROGRAM position and then hold the MENU switch down for 10 seconds.
19 LED DISPLA Y CALIBRA TION MODE DESCRIPTION MENU (-) (+) 4 C r u n MENU (-) (+) 4 C MENU (-) (+) 5 C E 0 0 MENU (-) (+) 6 C - - MENU (-) (+) P C 0 X X CALIBRA TING THE DISPENSER (Continued) - Right .
20 TROUBLESHOOTING GUIDE Error Codes When an error has occurred, all Door LED’ s will be flashing. Open the Door to access the LED Display and re- cord the Error Code.
21 Field Calibration of the Concentrate Pumps, Dispenser Flow Rates, and Hopper Powder Throw The factory set default values for the Pump & Dispenser Flow Rates are ver y accurate and typically do not need to be field calibrated.
22 Calibrating the Dispenser Flow Rates Decaf Coffee - Dispenser Flow Rate Calibration 1. Select RINSE on the Function Selector Switch, and PROGRAM of the Mode Selector Switch. Depress and Hold the MENU switch for approximately 10 sec. The unit will display “C1 run” when it has entered the Cali- bration Mode 2.
23 9. Install the coffee BIB’ s into the unit, and prime the pumps. Dispense several cups of both regular coffee and Decaf coffee. If either one or both the DECAF and HOT CHOCOLA TE LED illuminates during this process and dispensing is disabled, the EMPTY PRODUCT WARNING can be reset by priming the appropriate pump momentarily .
24 ELECTRICAL WIRING DIAGRAM SLCA-7 39328.3 012113 1 5 8 1 5 10 15 20 1 5 10 14 1 5 10 12 5 1 1 5 +V +V -V -V GROUND N/L2 L1 COM N.O. MAIN CONTROL BOARD J15 J3 J1 1 J6 J5 J11 J4 10 1 5 MENU (-) (+) J1.
デバイスBunn SLCA-7の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Bunn SLCA-7をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBunn SLCA-7の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bunn SLCA-7の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bunn SLCA-7で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bunn SLCA-7を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBunn SLCA-7の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bunn SLCA-7に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBunn SLCA-7デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
