ADTRANメーカー25の使用説明書/サービス説明書
ページ先へ移動 of 438
AT&T AT&T System 25 Installation and Maintenance Manual 555-540-103 B November 1995.
©1989 AT&T All Rights Reserved Printed in USA TO ORDER COPIES OF THIS DOCUMENT REFER TO DOCUMENT NUMBER 555-540-103 Contact: Your AT&T sales representative, or Call: 800-432-6600, Monday through Friday between 7:30 am and 6:00 pm EST, or In Canada call: 800-255-1242 Write: AT&T Customer Information 2855 North Franklin Road P.
DANGER Do not open the fan assembly or remove rear cabinet cover before unplugging the cabinet from the electrical outlet. Wait at least five minutes after unplugging the power cord before removing the rear cover or power supply. The AT&T System 25 cabinets are not user serviceable.
THE FOLLOWING SYMBOLS AND PICTOGRAPHS APPEAR ON THE EQUIPMENT SYMBOL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maint.
FCC NOTIFICATION AND REPAIR INFORMATION AT&T SYSTEM 25 This telephone equipment is registered with the Federal Communications Commission (FCC) in accordance with Part 68 of its Rules.
that certification in writing may be required when an existing multifunction system is being reconfigured as a Key system, if the customer desires the lower rate.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.
FCC WARNING STATEMENT Federal Communicatlons Commission (FCC) Rules require that you be notified of the following: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause interference to radio communications.
normally dialed from a telephone associated with the system. Such an off- premises network call is originated at, and will be billed from, the system location. The Remote Access feature, as designed, helps the customer, through proper administration, to minimize the ability of unauthorized persons to gain access to the network.
● When possible, block out-of-hours calling. ● Frequently monitor system call detail reports for quicker detection of any unauthorized or abnormal calling patterns.
Contents INTRODUCTION FCC PRECAUTIONS INSTALLATION TOOLS AND TEST EQUIPMENT CROSS-CONNECT EQUIPMENT DESCRIPTION Trunk Access Equipment 700A-110-BI -25 or 700A-66-B1-25 Cut-Down Jack 108 Emergency Tran.
TDM Bus Connections. Ground Wire Connections. POWER UP AND INITIALIZE SYSTEM Connect Power Connect Administration Equipment Cold Start the System Check Performance of Cabinet Components Report Problem.
Make SIP Connections for Data Terminals and Computers Make SIP Connections to Cabinet for ATL Cordless Telephones Perform SIP Housekeeping INSTALL EMERGENCY TRANSFER UNITS (ETUs) Make Emergency Transf.
7300H Series Voice Terminals INSTALL MUSIC-ON-HOLD INTERFACE FCC-Registered Music Source Interface Non-FCC Registered Music Source Interface INSTALL EXTERNAL ALERTS INSTALL RECORDED DELAY ANNOUNCEMENT.
MAKE POOLED MODEM TEST CALL . . . . TEST TRANSFER TO DATA . . . . ... . . . TEST EXTERNAL ALERT (NIGHT SERVICE) TEST TEST TEST TEST TEST 3-11 3-11 3-12 DICTATION SYSTEM ACCESS 3-13 PAGING INTERFACE MU.
ROUTINE MAINTENANCE Reseating and Replacing Circuit Packs Removing and Restoring Power Restarting the System ERROR LOG Accessing the Error Log From the SAT ERROR MESSAGES Clearing System-Detected Trou.
REFERENCES ABBREVIATIONS AND ACRONYMS 5-1 6-1 A-1 APPENDIX A: System Wiring Connector Pin Assignments System 25 Building Wiring APPENDIX B: Parts Listing Tables A-1 A-1 B-1 APPENDIX C: System Addition.
APPENDIX F: Administration Error Messages GLOSSARY INDEX F- 1 G-1 I- 1 -viii-.
Figures Figure 2-1. Figure 2-2. Figure 2-3. Figure 2-4. Figure 2-5. Figure 2-6. Figure 2-6a. Figure 2-7. Figure 2-8. Figure 2-9. Figure 2-10. Figure 2-11. Figure 2-12. Figure 2-13. Figure 2-14. Figure 2-15. Figure 2-16. Figure 2-17. Figure 2-18. Figure 2-19.
Figure 2-37. Figure 2-38. Figure 2-39. Figure 2-40. Figure 2-41. Figure 2-42. Figure 2-43. Figure 2-44. Figure 2-45. Figure 2-46. Figure 2-47. Figure 2-48. Figure 2-49. Figure 2-50. Figure 2-51. Figure 2-52. Figure 2-53. Figure 2-53a. Figure 2-54. Figure 2-55.
Figure 4-8. Figure 4-9. Figure 4-10. Figure 4-11. Figure 4-11.a. Figure 4-12. Figure 4-13. Figure C-1. Figure C-2. Figure C-3. Table 2-A. Table 2-B. Table 2-C. Table 2-D. Table 2-E. Table 2-F. Table 4-A. Table 4-B. Table 4-C. Table 4-D. Table 4-E. Table 4-F.
Table E-C. Table E-D. Table E-E. Table E-F. Table E-G. . . Table E-H. Table E-1. Table E-J. Table E-K. Table E-L. Table E-M. Table E-N. Table E-0. Table E-P. Table E-Q. Table E-R. Table E-S. Table E-T. Table E-U. Table E-V. Table E-W. Table E-X. Table E-Y.
INTRODUCTION INTRODUCTION This manual provides procedures and information for installing, and testing the AT&T System 25 Release 3 and associated equipment.
INTRODUCTION ● ● ● ● ● ● ● ● Section 5 References-Lists and describes other related documentatio n Section 6 Abbreviations and Acronyms-Lists and describes abbreviations and acronyms frequently encountered in System 25 documentation Appendix A.
INSTALLATION INSTALLATION Installation of a System 25 requires the completion of a number of basic steps, similar to those required to install any customer switching system. Assuming that the building (station) wiring is already in place, the recommended sequence of steps for installation of the system is as follows: 1.
INSTALLATION TOOLS AND TEST EQUIPMENT Table 2-A lists tools and test equipment required for installing a System 25. Table 2-A. Tools and Test Equipment Required for Installation Task s Tools Required .
INSTALLATION CROSS-CONNECT EQUIPMENT DESCRIPTION This section provides a brief description of some of connect/interconnect equipment. More details on the can be found in the Reference Manual (555-540-200).
INSTALLATION Trunk Access Equipment The trunk access equipment (TAE) consists of 700A-I 10-61-25 or 700A-66- B1 -25 (157BF) cut-down jacks, or equivalent, and up to four 10B Emergency Transfer Units (ETUs).
INSTALLATION NOTE: 9“ WIDE, MOUNTING CENTERS ARE 8-1/2” APART, FLANGES OVERLAPPED Figure 2-1. 10B ETU 2-5.
INSTALLATION Station Interconnect Panel (SIP) The SIP is the station cross-connect field and consists of the following equipment: ● 617A Panels ● Adapter s ● 50A Fanning Strips. 617A Panel The 617A Panel is a metal plate with keyslot holes on each side for mounting on a backboard.
INSTALLATION MOUNTING CENTERS WHEN FLANGES ARE OVERLAPPED Figure 2-2. 617A Panel 2-7.
INSTALLATION Adapters The adapters shown in Figure 2-3 are used at the SIP. Z210A2 or 858A Adapters These adapters connect the building wiring (station runs) to the station port circuit packs (CPs) located in the system cabinets (through octopus cables).
INSTALLATION Z21OA1 ADAPTER Y-ADAPTER WP90851,L1 858A ADAPTER Figure 2-3. SIP Adapters 2-9.
INSTALLATION Fanning Strip The 50A Fanning Strip (Figure 2-4) is a metal panel with positions to hold 16 octopus (switch) cables. The bundled portion of the octopus cable is anchored at the fanning strip. The eight octopus cable cords hang free. One fanning strip is required for 1-cabinet systems.
INSTALLATION Cables Splitter Cables The splitter cables (Figure 2-5) connect trunk circuits from the 700A jacks to the system cabinets or 10B ETU (3:1 only). 3:1 Splitter Cable (WP90929, L1) This cable connects the twenty-four 1-pair trunk circuits on a 700A jack to three 8-port trunk circuit packs (loop start, ground start, or DID).
INSTALLATION Octopus Cables Octopus cables (Figure 2-6) connect the station port and CPU/Memory circuit packs to the SIP adapters. Each cable consists of a 25-pair male connector that connects to the switch cabinet and eight modular plugs that connect to the SIP adapters.
INSTALLATION connector and a KS23146,L3 50-pin male connector. To connect a DS1 interface circuit pack to a 551-type Unit (CSU), field terminate the 15-pin plug. To connect DS1 tie trunks on co-located System 25s, 50-pin male connector (see Figure 2-1 9).
INSTALLATION AT&T CAR 1 CABLE LABELS CAB1 SLOT1 CAB1 SLOT1 CAB1 SLOT2 CAB1 SLOT2 CABl SLOT3 CAB1 SLOT3 CAB1 SLOT4 CAB1 SLOT4 CAB1 SLOT5 CAB1 SLOT5 CAB1 SLOT6 CAB1 SLOT6 CAB1 SLOT7 CAB1 SLOT7 CAB1 .
INSTALLATION Symbols Used in Figures Modular jacks are shown by the triangle symbol. The 25-pair connectors are indicated by shaded blocks. Generally, only one leg of an octopus cable is shown. Unterminated wiring requiring cut down or other termination does not show symbolic designations.
INSTALLATION PREINSTALLATION REQUIREMENTS The AT&T System 25 Reference Manual (555-540-200) provides a complete listing of System 25 equipment location requirements. Before installation begins, check the items described in this section. Caution: System 25 cross connect hardware must be located in a restricted access area only.
NOTES : 1. 2. 3. 4. 5. 115V AC, 60 Hz, 15 AMP OUTLETS (HUBBELL 5262 OR EQUIVALENT) MUST BE LOCATED WITHIN 4 FEET OF SYSTEM CABINETS. MULTIPLE CABINET SYSTEMS REQUIRE TWO QUAD OUTLETS, SINGLE CABINET SYSTEMS REQUIRE ONE QUAD OUTLET. ALLOW AT LEAST 24 INCHES OF SPACE IN FRONT OF CABINETS.
INSTALLATION AC Power All cabinets and any locally-connected System 25 peripheral equipment (System Administration Terminal [SAT], Station Message Detail Recording [SMDR] device, Digital Tape Unit [DTU]), and Customer Service Unit (CSU) used for DS1 connections must be plugged into the common ac power outlet.
INSTALLATION 3. 4. metal frame of the building, a concrete encased ground, or a ground ring. If these grounds are not available, the water pipe ground can be supplemented by one of the following types of grounds.
INSTALLATION ● A single-point ground (SPG) system in which the green wire ground (system ground) and the telephone company ground are connected to approved building ground. ● The coupled bonding conductor must be connected between the telephone company ground at the building entrance and System 25’s SPG.
INSTALLATION Secondary Protection External secondary protection, located at the trunk access area of the System 25 cross-connect field, is required for all trunks and off-premises lines.
INSTALLATION Building Wiring Building (station) wiring (must be 24 AWG or heavier) from voice and data terminals to the equipment location should already be in place. System 25 wiring requires that 4-pair circuits be distributed from the equipment location to each station’s wall jack.
INSTALLATION INSTALL SYSTEM CABINETS Before beginning the cabinet installation, position the cabinet table within 2 feet of the ac power receptacle. Make sure that the cabinets are easily accessible from both the front and the back. Position Cabinet(s) Caution: A fully-equipped cabinet weighs 80 pounds .
INSTALLATION Table 2-B. Circuit Packs, Their Functions, and Protectors Approved Secondary Circuit Pack Function Wiring Protector N/A ZTN78 Supports single-line voice terminals. (Must not be used on out-of-building circuits, ) SCP-1 or 79A TN742 Supports off-premises, out-of- building, and bridged single-line voice terminals.
INSTALLATION Two fans are located on the left-hand front side of each cabinet. The cabinet’s power supply is located behind the fans; to the right of the power supply are up to 12 CPs in individual slots. Each CP is identified by a label on the front.
INSTALLATION Figure 2-10. Three-Cabinet System, Front View With Covers Removed 2-26.
INSTALLATION Figure 2-11. Position of Shorting Plugs on CPU/Memory Circuit Pack 2-27.
INSTALLATION Required Circuit Pack Positions The required CP positions for Cabinet 1 are: SLOT CP 1 ZTN129 or ZTN130 (R3) I 2 I ZTN85 or ZTN131 (R3) Also, all DID Trunk circuit packs should be installed in Cabinet 1.
INSTALLATION Install 4A Retainer Clips The 4A retainer clips must be installed on each of the 12 receptacles on the lower rear panel of the cabinets. To install a clip, position it and insert the legs in the cabinet as shown in Figure 2-12. Figure 2-12.
INSTALLATION Connect Cabinets The Time Division Multiplex (TDM) bus extender cable and the intercabinet #6 AWG ground wire must be connected between cabinets. The TDM bus terminates on each side of the cabinet, and the intercabinet #6 AWG ground wire connects to the ground block at the rear of each cabinet.
INSTALLATION side up). 3. Install the upper rear panels. Route the extender cable between the slots formed by the upper and lower rear panels. 2-31.
INSTALLATION TDM BUS TER M CARD ADDR PLUG TDM B EXTEN CABLE ADD PL U PLU G Figure ~CABINET 3 ON/OF F .SWITC H AC POWE R # 6 AWG BUILDING GROUND WIR E CABINET 2 AC POWER .
INSTALLATION Ground Wire Connections The cabinets are connected to the single-point ground with #6 AWG copper wires. (Building ground requirements are described in Preinstallation Requirements in this section.) Warning: The cabinet power switches must be set to off.
INSTALLATION 5. Starting with Cabinet 2 or 3, turn on the power switch on each cabinet [Cabinet 1 must be last). IMPORTANT: If power to Cabinet 1 is not turned cold start initialization may not occur properly. 6. Check to be sure that the cabinet fans are rotating.
INSTALLATION Cold Start the System To ensure that the system recognizes the current position of the CPs, you must cold start the system before beginning initialization. A cold start causes the system to check all slots for valid CP types and assign default translations to ail ports (except auxiliary trunk ports).
INSTALLATION 7. The system will respond with: Action= 8. Enter 20 for a cold start. The system will respond with: Save/Restore: Action=20 Data= 9. Enter D. The system will complete the word Data followed by the = sign. 10. Enter 1 for a cold start or 2 for a limited cold start.
INSTALLATION Cold and warm starts both display the same type of information on the SAT. This consists of a listing of the version of the firmware loaded in the CPU/Memory CP, followed by a configuration listing of all CPs recognized by the system. The CPU/Memory CP is not in the configuration listing; however, it is located in slot 1 of Cabinet 1.
INSTALLATION The SAT message for a cold or warm start appears after the system has performed all self-tests and reading of its configuration. Typical cold start SAT message is as follows. The example is for a 2-cabinet system. Typical Release 3 Version 3 Cold Start Message RESTART TS ROM pair 1:version 3.
INSTALLATION Check Performance of Cabinet Components Each CP has three colored LEDs on the front panel that indicate whether it is functioning properly or not. When a cold start is performed, the system undergoes a series of self-tests and loads default translations.
INSTALLATION Table 2-D. Circuit Pack LED Status Indications Circuit Pack Type LEDs if Normal LEDs if Failed Service Circuit (ZTN85 Steady Green and Steady Red or or ZTN131 [R3]) Flashing or Amber Off .
INSTALLATION If all the CPs are operating properly, only the green LED on the CPU/Memory CP and the amber LED on the Service Circuit should be flashing. If any other CP has a no-lighted LED, the CP may need to be reseated. All port CPs green LED remains dark until at least one port on the CP has been translated.
INSTALLATION Figure 2-15. Typical System 25 Port Circuit Pack Report Problems Follow local procedures to report faulty or damaged equipment. 2-42 November 1995.
INSTALLATION Initialize System Instructions for initializing the system (based on the completed implementation forms) are provided in the Administration Manual (555-540-500). Note: Before trunks using DS1 Signaling are administered, all link level parameters such as signaling and framing and all link level alarms must be cleared.
INSTALLATION Install TAE, 617A Panels, and Fanning Strips To install this equipment, proceed as follows: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. For each RJ21X, RJ2GX, and RJ48X 700A Jack 1/2-inch from the edge of switch cabinet(s). Mount the first 617A Panel.
INSTALLATION FIRS T 108 ET U PLYWOO D BACKBOARD 1/2 " ADD'L 700A BLOCK ADD'L ET U ADD'L 700A BLOCK ADD'L 700A BLOC K ADD' L 617 A PANEL ADD'L 617 A PANEL ADD'L .
INSTALLATION NOTE: GREATER THAN 48" FO R 5-PANE L ARRANGEMEN T FIRS T 10 8 ET U Figure 2-17. Alternate SIP and TAE Backboard Layout 2-46.
INSTALLATION Mount 858A or 2210A2 Adapters To install these adapters, proceed as follows: 1. Using a wide blade screwdriver, pry off the upper adapter mounting clip on the 617A Panel (Figure 2-18). 2 . Fit the mounting clip on the top of the adapter. 3.
INSTALLATION UPPER ADAPTER MOUNTING CLIP Figure 2-18. Mounting Adapters.
INSTALLATION INSTALL MODULAR BULK POWER SUPPLY (Optimal) The 346 Modular Bulk Power Supply (MBPS) is a cost-effective and flexible alternative to the KS-2291 1 power supply. The 346 MBPS can be used where the wall-mounted (outlet) KS-2291 1 power supply cannot be used or where multiple KS-2291 1 power supplies are required.
INSTALLATION Tie trunks must be segregated on a separate block because a different splitter cable is used. Also, off-premises stations must be segregated one 700A Jack. The first five trunks in each group of eight (loop start or ground start trunks only) can be connected through an ETU to five power failure transfer stations.
INSTALLATION Connect Cabinets to TAE Blocks The connections between the cabinets and the TAE blocks are made using connectorized splitter cables. Make sure that each trunk group on each connecting block is connected to the correct type of CP and protected with its approved secondary protector (as shown in Table 2-B).
INSTALLATION Connect Tie Trunks A 2:1 connectorized splitter cable, WP90929, L3, is required to connect the 700A Jack to the cabinet for tie trunks. 1.
INSTALLATION Install DS1 DS1 signaling allows a digital connection between the System 25 and other PBXs, Central Offices, Toll Offices, off premise stations, and data end points such as host computers. The TN767 emulates ground start, Ioopstart, tie and DID Trunks in addition to off premises stations.
INSTALLATION Figure 2-19. Direct Connection (Side by Side) NOTE: FOR DISTANCES OVER 50 FEET (15.2 M) USE C6E CONNECTOR CABLE(S) BETWEEN H600 307,G2 CONNECTOR CABLE AND DS1 TRUNK CIRCUIT PACK.
Figure 2-21. DS1 Connections—1311 to 4310 Feet DS1 Connections—4311 Feet or More For distances of more than 4311 feet, T1 line repeaters are required in addition to the CSUs. See the “Install CSU” section of this manual for installing the CSU.
INSTALLATION Off Premises Metallic (Cable) Connections The connection between the System 25 and another DS1 interface is in most cases a T1 line with repeaters. The proper lightning protection must be provided (as shown in Table 2-B). Figure 2-23 shows a diagram of the off premise cabling.
INSTALLATION MICROWAVE INTERFACE MICROWAVE INTERFACE LIGHT-GUIDE INTERFAC E LIGHT-GUIDE INTERFAC E INFRARED INTERFACE INFRARE D INTERFACE 655 FEET MAXIMU M ANY DS 1 INTERFACE 655 FEET MAXIMUM ANY DS 1 INTERFACE Install *DSX-1 REFERS Figure 2-24.
INSTALLATION Connect the CSU The CSU can be powered by the line or from a locally provided -48 V dc power supply. Figure 2-25 shows the connections for connecting the CSU. The 48 V and GRD leads are optional according to how the CSU is powered. H600 307 ,0 2 CONNECTO R CABLE (NOTE) NOTE : FOR DISTANCES OVER 50 FEET ( 15.
INSTALLATION Consideration should be given to installing secondary protection on each out-of-building facility connected to the TAE if any of the following conditions exist : ● The service entrance (protector block) ground is not properly installed (bonded to building ground, for example).
INSTALLATION INSTALL EQUIPMENT ROOM STATION CABLING System 25 is connected to the building (station) wiring in two stages. First, the building wiring is connected to the Station Interconnect Panel (SIP). Then, the octopus cables from the back of the cabinets are connected to the SIP.
INSTALLATION . 2-61.
INSTALLATION Connect Building Wiring to SIP The type of building wiring termination determines what types of adapters are used. Two types are supported: 4-pair cable (cut down) and modular jack. Any combination of adapters may be mounted on a 617A Panel.
INSTALLATION Z21OA1 ADAPTER (MODULAR TO MODULAR) PURSE LOCK CLIP / ( TYPICAL) Figure 2-27. Modular Plug Terminations Connected to the SIP 2-63.
INSTALLATION 4-Pair Cable Terminations Each 4-pair cable supports one station (Figure 2-28). It connects to a wiring block on a 858A Adapter. 1. 2. 3. 4. 5. 6. Run the 4-pair cable through the rings at the top of the 617A Panels. Cut down the leads starting with Pin 1 of the wiring block located beside the modular jack (Figure 2-28).
INSTALLATION ZZ1OA1 ADAPTER (MODULAR TO MODULAR) PURSE LOCK CLIP (TYPICAL) Figure 2-28. Cut Down Terminations Connected to the SIP 2-65.
INSTALLATION Connect Cabinets to SIP Table 2-E shows the type of terminals that can be connected to each CP type and the maximum allowable cabling distances to the system cabinets. Refer to the Voice and Data Station Records Form for the terminal types assigned to each workstation.
NSTALLATION Prepare Carrier Loading Labels As you connect the port CPs in each cabinet to the SIP, list the connections on the Carrier Loading label. This label is mounted on the inside of the front cover of the cabinet. (See Figure 2-29.) Keep track of –48 volt power usage so that the power supply is not overloaded.
INSTALLATION 2-68.
INSTALLATION Modify Octopus Cables if Required If flag--type cable ties are shipped loose, they must be installed on the early production octopus cables. The flag-type cable tie location depends on the type of SIP arrangement (Figures 2-16 and 2-17). Also, if the alternate SIP arrangement is used, later production octopus cables must be modified.
INSTALLATION TO SWITCH TO SWITCH DISTRIBUTION RIN G FLATTEN OCTOPUS CABLE BEFORE FEEDING INTO TH E 50A FANNING STRIP ION THE FLAG MOD PLUG ENDS TO FAN OUT TO (D-RINGS) AS REQ’ D ADAPTERS ON SI P TIE WRAP IN FRON T OF THE WIRE FORM SI P FLAG TIE WRA P WITH OCTOPUS CABL E IDENTIFICATION LABE L Figure 2-30.
INSTALLATION Make SIP Connection for CPU/Memory In all cases, the CPU/Memory is connected to the SIP via an octopus cable. Since there are four ports on the CPU/Memory (port 1 for the SAT, port 2 for SMDR, port 3 for the DTU, and port 4 [reserved]), plugs 1 through 3 on the octopus cable are used to connect the peripheral equipment.
INSTALLATION FLAG-TYPE CABLE TIES STANDARD CABLE I MODIFIED CABLE FOR (FLAG TIE ALTERNATE SIP ARRANGEMENT AT 65” REMOVED) Figure 2-31. Mounting Octopus Cable on Fanning Strip 2-72.
INSTALLATION Make SIP Connections to Cabinet for 7300H Series Terminals 1. 2. 3. 4. 5. 6. 7. 8. 9. Select the cable label sheet (Figure 2-7) that identifies the cabinet (blue for #1, orange for #2, and green for #3).
INSTALLATION Make SIP Connections to Cabinet for MET Sets Follow the same procedure as for 7300H Series terminals to connect MET set SIP appearances to the appropriate CPs as outlined below: ● ● .
INSTALLATION ● Attach cable labels to the two octopus cable 25-pair connectors and flag-type tie wrap. ● Attach octopus cables to the 853B adapter ● Run the cables to the 50A Fanning Strip. ● Plug the cable ends into the appropriate adapters, and complete the Voice and Data Station Records Form.
INSTALLATION Make SIP Connections for Data Terminals and Computers Any RS-232C compatible data terminal, personal computer host computer, or a STAR LAN NETWORK workstation can be connected in one of four ways: ● If the terminal has a modem, it should be connected to a ZTN78 CP in the same way as a single-line voice terminal.
INSTALLATION 4. Complete the Voice and Data Station Records Form (Figure 2-26). Make SIP Connections to Cabinet for ATL Cordless Telephones Follow the same procedure as for 7300H Series terminals to c.
INSTALLATION 6. Check that all cables are labeled. INSTALL EMERGENCY TRANSFER UNITS (ETUs) The 106 Emergency Transfer Unit (ETU) (Figure 2-32) supports up to five Power Failure Transfer (PFT) sets and a DID make-busy function. Up to four ETUs can be supported for a maximum of 20 PFT sets.
INSTALLATION Figure 2-32. 10B Emergency Transfer Unit 2-78.
INSTALLATION Figure 2-33. Emergency Transfer Unit Connections 2-79.
INSTALLATION Make Emergency Transfer Connections Note: The following procedure assumes that the network interfaces 1. 2. 3. 4. 5. 6. 7. are connected to the 700A jacks and connector 0 of the 3:1 splitter cables has been connected to the jack. See Install Equipment Room Trunk Cabling in this part.
INSTALLATION 8. 9. 10. 11. 12. 13. Connect a 25-pair plug on octopus cable to the SIP receptacle on the ETU. Mount the octopus cable on the 50A Fanning Strip (Figure 2-31). Connect all eight legs of the octopus cable to adapters (port side) at the SIP.
INSTALLATION Install Ground-Start Key If trunks are ground start (ZTN76 used), a ground-start key must be installed on the Power Failure Transfer voice terminals. This key can only be installed on voice terminals that have modular jacks. 1. Unplug modular line cord from voice terminal.
INSTALLATION INSTALL ATTENDANT CONSOLE Most systems will have one or two attendant consoles. Release 2 Version 1 and Release 3 systems support direct trunk attendant consoles (DTAC) or switched loop attendant consoles (SLAC). The system can support either one or two of the DTAC or SLAC consoles but not a combination of DTACs and SLACs.
INSTALLATION Figure 2-35. Attendant Console With DXS Console 2-84.
INSTALLATION 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. lf a DXS is supplied, place it beside the attendant console. For locally powered DXS, do Steps 5 through 8. For remotely powered DXS, do Steps 9 through 13. Locally Powered DXS Plug the 400B2 Adapter into the wall jack.
INSTALLATION LEGEND : ZTN79 - B1 - cl - C2 - C7 - P2 - S1 - W1 - HYBRID LINE CP TYPICAL - 103A CONNECTING MODULAR CORD (D8W-87) OCTOPUS CABLE (WP90780) MODULAR CORD (D6AP-87) NODULAR BULK POWER SUPPLY POWER UNIT (346A) POWER PANEL (346A-1) BLOCK 23A1 SELECTOR CONSOLE-USED IN CONJUNCTION WITH EITHER SLAC OR DTAC INSIDE WIRING CABLE Figure 2-36.
INSTALLATION INSTALL TERMINALS When installing terminals at workstations, consult the Voice and Data Station Records Form to make sure that you are connecting the right terminal type at each workstation. In a replacement installation, single-line and MET voice terminals already in place may not need to be replaced, although the MET labels change.
INSTALLATION Label Terminals Be sure to label the feature buttons of 7300H Series voice terminals replace labels on MET sets per Table 2-F. Table 2-F. Feature Button Abbreviations and Labels Feature N.
INSTALLATION Table 2-F. Feature Button Abbreviations and Labels (Contd.) * [ ] Indicates that a meaningful value for this item should be substituted. † These features cannot be changed or reassigned.
INSTALLATION Stand-Alone Voice Terminals See Figure 2-37. 1. Unpack each terminal and examine it for damage. On Model 420 voice terminals, set the TONE/PULSE switch to TONE. 2. At the workstation, connect one end of the terminal line cord to the terminal and the other end to the modular wall jack.
INSTALLATION Stand-Alone Remotely Powered Voice Terminals See Figure 2-38. 1. Unpack each terminal and examine it for damage. 2. At the workstation, connect one end of the terminal line cord to the terminal and the other end to the modular wall jack.
INSTALLATION Single-Line and 7300H Series Voice Terminals With Associated ADUs See Figures 2-39 and 2-40. 1. 2. 3. 4. 5. 6. Unpack each voice terminal and ADU and examine them for damage. Arrange 7300H Series terminals and single-line terminals with appropriate ADUs (see Note).
INSTALLATION B1 - TYPICAL - 103A CONNECTING BLOCK Cl - MODULAR CORD (D8W-8T) C2 - OCTOPUS CABLE (WP90780) C5 - MODULAR CORD (D4BU-87) - FURNISHED WITH SET “ WI - INSIDE WIRING CABLE WP90851-L1 - MODULAR Y ADAPTER Z3A1 ADU - EQUIPPED WITH A 3 FOOT PLUG-ENDED EIA CORD NOTES : 1.
LEGEND: ZTN79 - TN726 - WP90851-L1 - B1 - C1 - C2 - P1 - W1 - Z3A5 ADU - HYBRID LINE CP Figure DATA LINE C P MODULAR Y ADAPTER TYPICAL - 103A CONNECTING BLOCK MODULAR CORD (D8W-87) OCTOPUS CABLE (WP90780) KS22911 POWER SUPPLY INSIDE WIRING CABLE EQUIPPED WITH A 3 FOOT PLUG-ENDED EIA CORD 7300H SERIES VOICE TERMINAL 2-40.
INSTALLATION Off-Premises Stations (TN742, TN746B in R3V2) An FCC-registered single-line terminal may Station (OPS). Note: Only the local telephone interconnections for the OPS.
INSTALLATION 4. Connect the cable to a protection device at the System 25 location. 5. Connect the second protection device to an 858A Adapter on the617A Panel, using 4-pair inside wiring cable. 6. Connect the 858A Adapter to a port on a TN742 circuit pack using an octopus cable.
INSTALLATION H600 307 .G 2 CONNECTO R CABLE (NOTE ) TO D4 CHANNE L BAN K NOTE; FOR DISTANCES OVER 50 FEET (15.2 M) USE C6E CONNECTOR CABLE(S) BETWEEN H600 307 .G2 CONNECTOR CABLE AND DS1 TRUNK CIRCUIT PACK . TO LOCALL Y PROVIDED -48 V POWER SUPPL Y Figure 2-41.
INSTALLATION Stand-Alone Data Terminals Data terminals and computers may be connected to the system through ADUs or a Multiple Asynchronous Data Unit (MADU) without being linked to a voice terminal. Depending on the data terminal that they connect to, some ADUs may need supplementary power for proper operation.
INSTALLATION LEGEND : . B1 - TYPICAL - 103A CONNECTING BLOCK C1 –MODULAR CORD (D8W-87) C7–MODULAR POWER CORD (D6AP-87) W 1 -4-PAIR INSIDE BUILDING WIRING CABLE 248B ADAPTER-ALLOWS MODULAR JACK CON.
INSTALLATION LEGEND : TN726 -DATA LINE CP B1 - TYPICAL - 103A CONNECTING BLOCK Cl -MODULAR CORD (D8W-87) C7-MODULAR CORD (D6AP-87) P2-MODULAR BULK POWER SUPPLY POWER UNIT (346A) POWER PANEL (346A-1) W.
INSTALLATION MADU Connections The MADU provides a direct connection to a host computer or a large group of data terminals (64 maximum). See Figure 2-44. The MADU has eight port connectors; each port is equivalent to a single ADU. Complete installation instructions for the MADU are contained in the MADU Product Guide (999- 700-525).
INSTALLATION INSTALL CUSTOMER’S SAT The SAT can be connected through the SIP to the CPU/Memory CP by any one of the following methods: l On-premises nonswitched connection (no ADU required if the SAT is plugged into the system AC outlet) l On-premises switched connection l Off-premises nonswitched connection l Off-premises switched connection.
INSTALLATION LEGEND : ZTN129-CPU/MEMORY CP C1 -MODULAR CORD (D8W-87) C2 -OCTOPUS CABLE (WP90780) 355A ADAPTER -RS-232 PLUG TO MODULAR JACK 355AF ADAPTER -RS-232 RECEPTACLE TO MODULAR JACK * PERIPHERAL.
Nonswitched See Figure 2-46. Connection of Equipment Note: Figure 2-46 shows an Z210A1 SIP Adapter to provide the building wiring termination. An 858A Adapter can also be 1. 2. 3. 4. 5 . 6 . 7 . 8. 9 . 10. used. Connect the RS-232C plug on the peripheral 232C port on a Z3A1 or Z3A4 ADU.
INSTALLATION LEGEND : B1 –TYPICAL - 103A CONNECTING BLOCK C1 -MODULAR CORD (D8W-87) C2 -OCTOPUS CABLE (WP90780) C3-EIA CROSSOVER CABLE (P17U-87) C4 -MODULAR RECEPTACLE TO MODULAR PLUG ADU CROSSOVER .
INSTALLATION On-Premises Digital Switched Connection To access a CPU/Memory port through a switched connection, the port is connected to a port on a TN726 CP and assigned a Data Dial Code (DDC). See Figure 2-47. The peripheral equipment can be either stand-alone or associated with a voice terminal.
INSTALLATION 11. Connect the other end of the modular cord to a 355AF Adapter. 12. Connect an M7U-87 Cord to the 355AF Adapter. 13. Connect the other end of the M7U-87 Cord to the RS-232C jack on a Z3A4 ADU . 14. Connect the ADU to a 400B2 Adapter with a D8W-87 cord.
INSTALLATION LEGEND: B1 - TYPICAL - 103A CONNECTING BLOCK cl - MODULAR CORD (D8U-87) C2 - OCTOPUS CABLE (UP80780) C3 - EIA CROSSOVER CABLE (M7U-87) C7 - MODULAR POUER CORD (D8AP-87) W1 - INSIDE 8UILDI.
INSTALLATION Off-Premises Nonswitched Connection Off-premises peripheral equipment must be equipped with an originating modem (see Figure 2-48). The connection is made from the CO through the TAE to a dedicated modem (optioned for autoanswer) connected to the appropriate Call Processor port.
INSTALLATION SYSTEM 2 5 CABINE T PART O F OCTOPU S CABL E CO OR PROVATE LINE CIRCUIT PART OF SI P CONNEC T VIA TA E ZTN12 8 OR ZTN13 0 Z210A 2 ADAPT. TYPICAL MODE M TELC O CENTRA L OFFIC E 355A F *PER.
INSTALLATION INSTALL CUSTOMER’S DTU The DTU must be directly connected to Port #3 on the CPU/Memory CP (Figures 2-45 and 2-46). Remote and switched connections are not supported.
INSTALLATION INSTALL STARLAN NETWORK INTERFACE Note: Support for the STARLAN Interface has been discontinued. The ZTN84 STARLAN Interface CP provides an interface between the System 25 TDM bus and a STARLAN NETWORK local area network (LAN). An octopus cable connects the ZTN84 CP to a Network on the STARLAN NETWORK (Figure 2-49).
INSTALLATIO N Shared System 25 Voice/STARLAN NETWORK Data Connections STARLAN NETWORK workstations can share the 4-pair System 25 wiring to the SIP with an analog or 7300H Series voice terminal. The STARLAN NETWORK data is transmitted over pairs two and three.
INSTALLATION STARLAN NETWORK NEU PART OF SI P SYSTEM 25 CABINE T Y ADAPT (WP90851- L1 ) SI P ADAP T (TYP ) ZTN7 8 O R TN74 2 PART OF OCTOPUS CABL E PERSONA L COMPUTER STARLAN NETWORK WORKSTATIO N LEGEND : ZTN78 - TN742 - 699Y - B1 - C1 - C2 - C5 - W1 - MP90851-L1 - NOTES : 1.
INSTALLATION 73001H Series Voice Terminals See Figure 2-51. 1. 2. 3. 4. 5. 6. 7. Unpack each terminal and examine it for damage. At the workstation, use a D8W-87 modular cord to connect the NAU jack on the KS-23475, L1 Adapter to the OUT jack on the NAU.
INSTALLATION LEGEND: ZTN79 - WP90851-L1 - A2 - B1 - C1 - C2 - C3 AND C4 - P1 - W1 - Figure 2-51. HYBRID LINE CP MODULAR Y ADAPTER KS-23475 ADAPTER TYPICAL - 103A CONNECTING MODULAR CORD (D8W-87) OCTOP.
INSTALLATION INSTALL MUSIC-ON-HOLD INTERFACE Note: Use of equipment that rebroadcasts copyrighted music or other material may be required to obtain a license from a third party such as ASCAP or BMI. FCC-Registered Music Source Interface The music source is connected to a ZTN78 CP through the SIP (see Figure 2-52).
INSTALLATION LEGEND : TN742 – ZTN78 – B1 - C2 - C5 - W1 – MOH - ANALOG LINE CP TIP RING CP TYPICAL - 103A CONNECTING BLOCK OCTOPUS CABLE (WP90780) PEC 2720-05P MODULAR CORD (D4BU-87) INSIDE WIRING CABLE KS-23395 INTERFACE Figure 2-52.
INSTALLATION Non-FCC Registered Music Source Interface The music source is connected to a ZTN78 CP (see Figure 2-53). Connect the CP to a 858A Adapter at the SIP.
INSTALLATION Music Source (Customer supplied) Music-on-Hold interfac e (KS-23395 ) G R GR GR MSH I ❑ ❑ ❑ (Optional) DW8A-SE 909A/ B Univversal Coupler (Replaces 36A Voice Coupler) MSHI CT CT J 2 MSLO MSLO CR C R Twisted Pair 26AWG Min.
INSTALLATION 2-119b This page intentionally left blank. November 1995.
INSTALLATION INSTALL EXTERNAL ALERTS External 54). 1. 2. 3. alerts are connected to the system through a ZTN78 CP (Figure 2- Connect the CP to a 858A Adapter at the SIP. Connect the other side of the adapter to a 103A Connecting Block using building wiring.
INSTALLATION INSTALL RECORDED DELAY ANNOUNCEMENT Dela y announcements are installed the same way as external alerts. INSTALL DICTATION SYSTEM INTERFACE If the equipment does not require a contact closure, follow the instructions for installing external alerts.
INSTALLATION Direct Connection to TN763 Auxiliary Trunk CP Paging (Figur e ● ● equipment can be connected directly to a TN763 Auxiliary Trunk CP 2-55) when the following conditions exist: Paging equipment is FCC registered. Paging equipment requires a contact closure Connect as shown in Figure 2-55, following the steps 1.
INSTALLATION SYSTEM 2 5 CABINE T PART O F 25 PAIR CABL E PART O F 66-BLOC K A W 1 C 5 TN76 3 B 1 < PAGING O R DICTATION SYSTE M LEGEND : TN763– AUXILIARY TRUNK CP A – SINGLE-ENDED 25 PAIR CONNE.
INSTALLATION Connection to TN763 Auxiliary Trunk CP (278A Adapter Required) A 278A Adapter is required to connect paging equipment to a TN763 Auxiliary Trunk CP (Figure 2-56) when the following conditions l Paging equipment is not FCC registered. l Paging equipment requires a contact closure Connect as shown in Figure 2-56, following the steps 1.
INSTALLATION Loudspeaker Syste m Cros s Connect Fiel d Red 103A o r Wal l Jack Green Line Cord B25 A o r A25 D Auxiliary Cabinet or Wall Field T 25-Pair F Conn.
INSTALLATION This page intentionally left blank. 2-124b November 1995.
INSTALLATION 5. 6. 7. 8. 9. 10. 11. Set switch to NORMAL position. Using a D4BY (single-ended) modular cord, connect D-181321 kit of parts (Figure 2-56) to a KS-22911, L2 power supply (-48V dc).
INSTALLATION LEGEND : TN763 - AUXILIARY A - B1 - C5 - C6 - P1 - W1 - 278A SINGLE-ENDED TRUNK C P 25 PAIR CONNECTOR CABLE (A25D) TYPICAL - 103A CONNECTING BLOCK MODULAR CORD (D4BU-87) SINGLE-ENDED MODULAR CORD KS-22911, L2, POWER SUPPLY, -48 VOLT DC INSIDE WIRING CABLE (4-PAIR) ADAPTER -REQUIRES –24 VOLT ZENER DIODE KIT OF PARTS NOTES : 1.
Figure 2-57. 278A Adaptor Plug Positions for Connecting TN763 Circuit Pack to Paging System 2-127.
INSTALLATION Connection to ZTN76 or ZTN77 CP PagePac 20 system with ZoneMate 9/39 and Common Control Unit (CCU) provides up to nine/thirty-nine paging zones and multizone groups. To connect a PagePac 20 system, make connections using the following steps (Figure 2-58): 1.
INSTALLATION LEGEND : ZTN76 - ZTN77 - A - B1 - C5 - W1 - GROUND START C’ LOOP START C’ 3 TO 1 SPLITTER CABLE (WP-90929,L1) TYPICAL - 103A CONNECTING BLOCK MODULAR CORD (D4BU-87) INSIDE WIRING CABLE (4-PAIR) Figure 2-58.
INSTALLATION Customer-provided paging equipment can also be connected to ZTN76 or ZTlN77 CO trunk CPs. Connection to the system is made through the TAE appearance of the Tip/Ring pair of the CO trunk CP (See Appendix A for connection details).
INSTALLATION LEGEND : ZTN76 - GROUND START CP ZTN77 - LOOP START CP A - 3 TO 1 SPLITTER CABLE (WP-90929,L1) UPAM - UNIVERSAL TELEPHONE (PAGING) ACCESS MODULE P 1 - PRS-48 POWER SUPPLY W1 - INSIDE WIRING CABLE (4-PAIR) NOTES : 1. APPARATUS CODE D-181523 INCLUDES 66E3-25 BLOCK CONNECTOR AND CABLE B25A 15/DE.
SYSTEM TESTS SYSTEM TESTS Once installation is completed, the system must be initialized, following the procedures in the AT&T System 25 Administration Manual (555-540-500). When this has been done, the system is ready for acceptance testing. You should test all trunks, voice terminals, data terminals, and features.
SYSTEM TESTS TEST INCOMING DID TRUNKS You can test DID trunks by establishing a connection on each DID trunk and then busying it out so that all DID trunks can be tested. 1. 2. 3. 4. 5. 6. 7. At a working voice terminal, go off-hook, dial the CO trunk access code, and then dial a DID number.
SYSTEM TESTS 4. Repeat Steps 1 through 3 for all incoming tie trunks, and make sure each tie trunk is tested. TEST 7300H SERIES VOICE TERMINALS Test each 7300H Series terminal using the terminal’s test switch, by placing both station-to-station and external calls, and by using the feature buttons.
SYSTEM TESTS 8. 9. 10. 11. 12. 13. 14. Dial the Dial the central office (CO) trunk access code. You should hear the CO dial tone. listed directory number for the system you are installing. You should hear ringback at the calling terminal and ringing at the attendant console.
SYSTEM TESTS TEST SINGLE-LINE VOICE TERMINALS Test each single-line voice terminal by placing station-to-station and external calls. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. At the test terminal, go off-hook. — You should hear system dial tone. Dial the PDC of another working terminal.
SYSTEM TESTS TEST ATL CORDLESS TELEPHONE The ATL Cordless Telephone must be tested to see The transmission quality must be verified when the separated by the maximum operating distance. if it functions properly. base and handset are Use the documentation provided with the ATL Cordless Telephone to perform the required tests.
SYSTEM TESTS 2. 3. 4. 5. 6. At any multiline voice terminal, go off-hook, dial the ARS access code, and dial one of the long-distance numbers. Make sure that the call is completed before going on-hook. Repeat Step 2 if additional long-distance numbers must be called.
1. 2. 3. 4. Test PDC Login At a voice terminal, go off-hook and dial * * PDC PDC, where PDC is a PDC other than that of the test terminal. — You should hear a confirmation tone. At another voice terminal, go off-hook and dial the PDC that was logged into the first terminal.
SYSTEM TESTS TEST ATTENDANT CONSOLE Testing the attendant console is the same as testing a multiline voice terminal, except for testing the console’s unique feature buttons. 1. Perform all the steps in “Test 7300H Series Voice Terminal” in this section.
SYSTEM TESTS TEST DATA TERMINAL DIALING FEATURE Perform this test on all data terminals and personal computers connected to the system through ADUs. 1. 2. 3. 4. 5. 6. 7. Make sure the test terminal is on. Press <BREAK> <RETURN>. The command mode menu is displayed.
SYSTEM TESTS MAKE POOLED MODEM TEST CALL Skip this test if the system does not include a TN758 Pooled Modem CP. This test involves placing a data call from a data terminal connected through an ADU from a data terminal or personal computer connected via a modem (the modem may be part of a terminal connected to System 25 or off premises).
SYSTEM TESTS TEST EXTERNAL ALERT (NIGHT SERVICE) Place a sounds alerting alerting 1. 2. 3. 4. 5. 6. 7. 8. test call to the attendant console to verify that the alerting device when device device At the the attendant console is in the Night Service mode.
SYSTEM TESTS TEST DICTATION SYSTEM ACCESS Place a call to verify that dictation equipment can be accessed. If dictation equipment has not been installed, this feature cannot be tested. 1. 2. 3. 4. 5. Use a working voice terminal as the test terminal, and go off-hook.
SYSTEM TEST TESTS MUSIC-ON-HOLD Verify that music is provided to outside callers placed on hold. (Inside callers do not receive Music-on-Hold [MOH].) 1. 2. 3. 4. 5. At any working voice terminal, go off-hook. Dial the CO trunk access code and the system’s listed directory number, or if DID, dial any station.
SYSTEM TESTS TEST EMERGENCY TRANSFER Place the system in emergency transfer mode by turning power off (or remove the modular connector from the ETU). Place an outside call from each emergency transfer station. 1. 2. 3. 4. 5. 6. 7. 8. At Cabinet 1, turn the power off using the rocker switch on the back or remove the modular connector from the ETU.
SYSTEM TESTS TEST TOUCH-TONE RECEIVERS 1. 2. 3. At a single-line voice terminal, go off-hook. Dial *3 and the 2-digit number (01 through 12) of the touch-tone receiver to be tested.
MAINTENANCE MAINTENANCE The primary maintenance objective is to detect, report, and clear troubles as quickly as possible with minimum disruption to normal service. Periodic system self-tests, automatic software diagnostic programs, and fault detection hardware are several of the maintenance tools used to achieve this objective.
MAINTENANCE EQUIPMENT NEEDED The any maintenance technician System 25 service call: should take the following tools and equipment on EIA breakout box Digital voltmeter (KS-20599 or equivalent) 11 O/66.
MAINTENANCE Precautions Electromagnetic fields radiating from the system cabinets may generate noise in other communications equipment. The technician must be sure that all cabinet panels and covers are securely in place after performing maintenance. Caution: Electrostatic discharge can destroy or severely damage integrated circuits on CPs.
MAINTENANCE GENERAL MAINTENANCE INFORMATION System Errors and Alarms During periodic testing, a maintenance audit could detect a system error that automatically generates an error record.
MAINTENANCE Memory (ZTN81 [RIV7] or ZTN127 [RI V2]J: The red LED on this CP lights when power is applied and goes dark upon successful completion of the ROM checksum test initiated by the Call Processor CP. Failure is indicated by a steadily lighted red LED.
MAINTENANCE Attendant Console LED A lighted green Alarm LED on the console indicates the presence of a Permanent System Alarm. The LED flashes with each new alarm. The attendant can press the associated button to cause the LED to light steadily. A lighted red Alarm LED indicates a barrier code violation.
MAINTENANCE Using RIMS, the remote administrator can initialize translations after the switch itself is installed. As long as there is no hardware change, the remote administrator can do ongoing administration without having to visit the customer’s site.
MAINTENANCE Administration Requirements For a RIMS call to be made during initialization, at least one voice station and one trunk must be translated. A cold start with defaults provides these translations. The RIMS transfer code (*1 00) can be assigned to a Repertory Dialing feature button on a multiline voice terminal.
MAINTENANCE MAINTENANCE STRATEGY Fault isolation is the cornerstone of the System 25 maintenance strategy. Maintenance activity isolates faults to one (or more) repairable or replaceable maintenance units. Equipment should be tested in the following order: 1.
MAINTENANCE SYSTE M TROUBL E REPORTED USER-REPORTED DISCUSS THE TROUBLE WITH SYSTEM USERS CAP ALARM REPORTED CAP ALARMED READ PERMANENT SYSTEM ALARMS TABLE IN ERROR LOG : AND CHEC K CIRCUIT BOARDS AND.
MAINTENANCE Sometimes, faults recorded in the error log and user-reported troubles will exist at the same time. The logged faults should always be cleared first, if possible. This procedure often clears the user-reported troubles without any additional maintenance.
MAINTENANCE Common Control Problems Common Control circuitry is difficult to troubleshoot. The system must be powered down before any of these CPs are replaced. Before powering the system down, save translations to tape (see “Using the Digital Tape Unit”).
MAINTENANCE Station, Wiring, and Trunk Problems If the system indicates that a fault is with a station, or if a user complaint indicates a station problem, the trouble must be isolated to the station itself or to the wiring between the cabinet or station interconnect panel and the station.
MAINTENANCE USING THE DIGITAL TAPE UNIT The Model DC4 Digital Tape Unit (DTU) or equivalent is extremely important in system maintenance. System Translations are stored in the DTU and can be accessed in the unlikely event that translations are lost during a system failure .
4. Press the REWIND button, and wait for the unit to tape. This step ensures that the tape is played from Note: The system automatically compensates for “leader” material at the beginning and end of the Saving Translations Follow these steps to save 1.
MAINTENANCE 9. 10. Press c to continue, and the tape unit is automatically started by the system. Saving translations on tape takes about 5 minutes and does not affect switch performance. When the save is complete, the unit stops automatically. If the save is successful, the SAT displays: SAVE COMPLETED SUCCESSFULLY.
MAINTENANCE 5. 6. 7. . 8. 9. 10. Enter 2. The system responds with: Save/Restore: Action=2 Data=. Enter D. The system completes the word Data followed by the = sign.
MAINTENANCE Restoring Translations Note : Restoring translations from tape removes the system from operation for about 5 minutes. When it is necessary to restore system translations from tape, follow these steps: 1. 2. 3. 4. 5. 6. 7. Complete the steps under “Setting up the DTU,” using the cassette on which translations were saved.
MAINTENANCE 8. 9. 10. 11. Press c for continue, and the tape unit is automatically started by the system. Restoring translations takes about 5 minutes.
MAINTENANCE ROUTINE MAINTENANCE The following are general trouble-clearing techniques usually required to resolve system-detected and/or user-detected troubles. ● Reseating and Replacing Circuit Packs ● Removing and Restoring Power ● Restarting the System.
MAINTENANCE 6. Inspect the cabinet backplane and the connectors at the back of the CP. It may be possible to clean dirty connectors per prescribed procedures and return the CP to service. However, if any connectors are damaged or corroded the CP should be replaced.
MAINTENANCE Removing and Restoring Power When the following procedures are performed, the system must be unplugged from the ac power source: ● ● ● ● Reseating or replacing the Service Circuit .
MAINTENANCE Restarting the System The system automatically warm starts after power is restored. (The system’s maintenance software may restart the system under certain self-detected error conditions.
MAINTENANCE 6. 7. 8. 9. Enter 9 (for the SAVE/RESTORE selection) and press <RETURN>. The system responds with: Action = Enter 10 for a warm restart. The system responds with: Save/Restore: Action=10 Data=. Enter D. The system responds with: Data = 10.
MAINTENANCE Messages displayed on the SAT indicate which restart is being performed. The same type of information is displayed for a cold and a warm restart. This information consists of a listing of the version of the firmware loaded in the CPU/Memory CP and a configuration The CPU/Memory CP is not listed in be located in slot 1 of Cabinet 1.
MAINTENANCE The SAT message for a cold restart appears after the system has performed all self-tests and reading of its configuration. The time required for a cold start depends on the number of CPs in the system but is generally several minutes.
MAINTENANCE ERROR LOG When a system maintenance object fails periodic testing, the system automatically generates an error record. Depending on severity, the record is stored in one of three tables in the Error Log.
MAINTENANCE A typical error record from the Permanent System Alarms and Transient System Errors table is as follows: PERMANENT SYSTEM ALARMS PORT BOARD FIRST LAS T COUNT NAME NUMBER CODE OCCURRED OCCU.
MAINTENANCE Error records in the Most Recent System Errors table have a slightly different format. A typical error record from the Most Recent System Errors table is MOST RECENT SYSTEM ERRORS POR T BO.
MAINTENANCE The Error Log is under the control of internal background maintenance software that automatically escalates an error to a more serious category or retires it. The system tests itself after a repair has been made. If the error condition is corrected, the error may be removed from the Error Log.
MAINTENANCE 9. 10. 11. 12. . If you Enter 1 and press <RETURN>. The SAT displays: SEARCHES: ACTlON=1 DATA= Enter D. The system completes the word Data followed by the = sign.
MAINTENANCE ERROR MESSAGES Error messages, along with the alarm indicators, are the most likely indicators that an error has occurred in the system. When a maintenance object fails periodic testing, the system automatically generates an error record. The error record (log) is accessible through the SAT.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTIO N AC Power Failure: An indication Check plug at wall receptacle. If that ac power has been lost (for this error occurs more often than example, plug removed from a the building power outages, check wall receptacle, building power connection to wall.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Bad Port: (STARLAN Interface Recoverable; no action required. CP) This error is an isolated transient condition. Bad Ringing Supply: Problems Check ring voltage on associated detected with ringing portion of power supply (see Figure 4-2).
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION D C Fai l Transien t Record : No action required; this error Indicates a dc power failure. display is a record of the start time of the failure. DC Power Failed: Indicates the Check the +5 V dc voltage level absence of +5 V dc on a cabinet.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION DXS Reset; The DXS console has Recoverable; no action required. been reset. Electronic Powe r Feed Off , Check the wiring for shorts from Overcurrent: A Hybrid Line the backplane/SIP up to the (ZTN79) port EPF chip shut down.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION External Stack Full: (STARLAN If the reset is not successful Interface CP) This error resets the reseat board. If the reseat fails, CP . replace the board. Fault o n Outgoing Seizure: Check trunk for slow dial tone; ZTN76/TN747 CO ground was not more than 10 seconds.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Illegal Instruction: This error is The Problem could be with the logged when an illegal instruction ROM on the CPU/Memory CP. If is encountered by the CPU. the problem persists, check or replace CP.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Invalid Message Length: The port If the problem persists, check or CP sent an up-link message that replace the port CP.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Memory Management Error: Bu s Possible softwar e error. If error that occurs while accessing problem persists, check o r the “other than protected” RAM. replace CPU/Memory CP. A A warm start is logged after this warm start or retranslation of the error .
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION On-HookBeforeReady To Receive Digits: For a tie trunk with delay dial or wink start—after the handshake is complete, a 50-ms guard time must pass before digits are received. If the far-end goes on-hook before guard time elapses, this message is logged.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Port CP Missing Bu t Check CP slot; reseat CP; change “Administered: (Other tha n CP; or remov e C P fro m CPU/Memory) Translated port CP translations. If CP does not pass that CPU cannot access.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Received Incorrect Number of DID Digits: This error indicates that the CO is set up to send a number of DID digits different from what the switch has been administered to receive. Ensure that trunks are properly translated.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Servic e Circuit Test Failed: Check TDM bus terminator and Service Circuit demand test failed cabinet interconnect cables. If the on the DTMF receivers. problem persists, replace ZTN85 or ZTN131 (R3).
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Trunk Call Dropped: A call that Normally, no action required; had been up on a trunk for more however, if problem persists, than 9 hours has been detected perform trunk test call per Trunk by an audit and dropped.
MAINTENANCE ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION Unrecognized Command: Recoverable; no action required. (STARLAN Interface CP) This error is an isolated transient condition. User Forced Warm Start: System Recoverable; no action required. was warm started through the SAT.
MAINTENANCE . . Figure 4-2. Clearing Supply Troubles (Sheet 1 of 2) 4-47.
MAINTENANCE Figure 4-2. Clearing Power Supply Troubles (Sheet 2 of 2).
MAINTENANCE Figure 4-3. Clearing CO Trunk Troubles 4-49.
MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 1 of 4) 4-50.
MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 2 of 4) 4-51.
MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 3 of 4) 4-52.
MAINTENANCE Figure 4-4. Clearing 4-Wire Tie Trunk Troubles (Sheet 4 of 4) 4-53.
MAINTENANCE NOTES : 1. PC should be running NAUCOM, Session, CAM and/or any STARLAN NETWORK compatible emulating program . 2. The green LED lights when the STARLAN CP passes power up.
Figure 4-6. Clearing Tie Trunk Troubles (Sheet 1 of 5) 4-55.
MAINTENANCE [6] [7] [8] [9] [10] Figure 4-6. Clearing Tie Trunk Troubles (Sheet 2 of 5) 4-56.
MAINTENANCE Figure 4-6. Clearing Tie Trunk Troubles (Sheet 3 of 5) 4-57.
MAINTENANCE Figure 4-6. Clearing Tie Trunk Troubles (Sheet 4 of 5) 4-58.
MAINTENANCE Figure 4-6. Clearing Tie Trunk Troubles (Sheet 5 of 5) 4-59.
MAINTENANCE Figure 4-7. Clearing Paging Equipment Troubles.
MAINTENANCE Clearing System-Detected Troubles Most troubles are detected through the Alarm LED located on the Attendant Console, the Error Log, and, in some cases, the LEDs on the circuit packs (CPs). The following is a list of system troubles. Each item in the list is described in this section.
MAINTENANCE Failure of the CPU/Memory CP at power-up generates the following type of error message: FAIL: <CARD>: <TEST>: <DETAIL>: The bracketed fields contain the following informa.
MAINTENANCE After total failure, the system ceases to operate and the green LED on the CPU/Memory CP may not flash. Failure can also be verified by checking the LEDS on each CP. If either a partial or total Common Control failure is detected, remove and then restore system power.
MAINTENANCE Once a faulty CP is identified, it can be replaced using the procedures in “Reseating and Replacing Circuit Packs” under “Routine Maintenance. ” Refer to the information in “Circuit Pack LEDs” under the “General Maintenance Information” to understand the meaning of the CP LEDs.
MAINTENANCE Table 4-B lists the test points (-5 V, +5 V, -48 V, and GND) for the power supply. The test points are located on the upper-right corner at the front of the cabinet. Table 4-C lists the voltages used by the CPs and symptoms voltages are missing.
MAINTENANCE Table 4-C. Circuit Pack Voltage–Symptoms Voltage/ +5 volts -5 volts -48 Volts Circuit Pack (Notes) No+5 V No-5 V No-48 V Call Proc. (ZTN82, x System Failure x EIA Failure x ETU Activated.
MAINTENANCE Each power supply has one green LED on its front that can be seen through the fan assembly. The LED is visible through the ventilation slots on the front cover, but the cover must be removed for diagnostic and service purposes. This LED is always lighted when the system is receiving 5.
MAINTENANCE AC DISTRIBUTION UNIT AC CIR D VARISTOR PWB ASSY CM 538A1 S1 SW TO 15 A 120 VAC OUTLE T GROUND BLOC K Figure 4-8. AC Power Schematic 4-68.
MAINTENANCE Power Supply Protection Power supply outputs are protected from damage when they are subjected to either momentary or sustained short circuits. “Shutdown” current protection is provided at 125 percent (plus or minus 5 percent) of full load for each dc output.
MAINTENANCE Power Supply Replacement To replace the power supply, follow these steps: Danger: Hazardous voltages are present on some backplane 1. 2. 3. 4. 5. 6. 7. 8. pins. Unplug power cord from the outlet, and wait at least 5 minutes before removing rear cover or power supply.
MAINTENANCE Fan Assembly Trouble The fans should always be operating when the system is receiving ac power and the cabinet switch is turned on. If the fans are not operating, be sure that the system is receiving ac power.
MAINTENANCE Overheating Trouble A clogged or dirty air filter can cause the cabinet to overheat. The cabinet air filter rests on the floor of the cabinet under the CP carrier. The air filter should be inspected on any service call and replaced as needed (with air filter comcode 845948348).
MAINTENANCE TEST POINT CABLE CONNECTS I HERE. ACCESS VOLTAGE TEST ADDRESS PLUG POSITION POINTS FROM FRONT OF (SLOT 08 NOT USED) CABINET. Figure 4-9. System Cabinet Backplane Wiring Side (Sheet 1 of 2).
MAINTENANCE Figure 4-9. System Cabinet Backplane Wiring Side (Sheet 2 of 2) 4-74.
MAINTENANCE Figure 4-10. TDM Signal Designations on Cabinet Backplane 4-75.
MAINTENANCE Figure 4-11. Power Designations on Cabinet Backplane 4-76.
_ MAINTENANC E Each of the 12 universal carrier slots has 48 pins on the backplane for connection to station and trunk ports. The 48 pins are divided into eight groups of 6 pins each, one group for each port circuit. Lead designations consist of the lead name suffixed by the group number (for example, TA.
MAINTENANCE Table 4-D. 25-Pair Connector to Backplane Designations 25-Pin-Conn . Cal l Pro c Pin No. Wir e Colo r G S Trun k ZTN7 6 L S Trun k ZTN7 7 Tip Ring Lin e ZTN7 8 AT L Lin e ZTN7 9 ME T Lin e TN73 5 Backplan e Pin No .
MAINTENANCE Table 4-D. 25-Pair Connector to Backplane Designations Contd) 25-Pin-Conn. . Pin No. Wir e Colo r DI D Trun k TN753 Ti e Trun k TN760B Aux . Trun k TN763 Dat a Lin e TN72 6 Analog Lin e TN74 2 Analo g Lin e TN746 B DS 1 Interfac e TN76 7 Backplan e Pin No .
MAINTENANCE 8' CABLE LENGTH CONNECTOR 1 CONNECTOR 0 CONNECTOR 2 STOCKLIST DESCRIPTION 25-PR PLU G 8-FT, 8-PR, 24-GC, CABLE 25-PR RECEPTACLE SPACER (NOTE 1) NOTES: 1. 2. 3. INSTALL SPACER AT CONNECTOR CABLE CLAMP TO ENSURE PROPER CABLE RETENTION. ITEMS 1 AND 3 SHALL BE EQUIPPED WITH SCREWS TO FACILITATE ASSEMBLY TO B25A CABLES.
MAINTENANCE Emergency Transfer Unit Troubl e If the Emergency Transfer Unit (ETU) will not enter the power failure mode, do the following steps: 1. 2. 3.
MAINTENANCE CLEARING USER-DETECTED TROUBLES User-reported troubles are usually associated with voice or data terminal equipment or trunks. They can result from system-detected errors and are often solved by clearing system error conditions or alarms. This section presents trouble-clearing techniques and procedures for user- reported troubles.
MAINTENANCE Note : For problems with administration equipment that is not connected on a dedicated basis, refer to the Terminal Operations Manual, 555-540-710. Time-Keeping Troubles Symptoms: Clock Procedures: 1. Reset doesn’t reflect current time or date.
6. 7. 8. 9. Voice Check CP translations from the SAT to be sure that this CP has Check LEDs on CP. The red LED will be lighted if a fault on the CP affects all ports. Also, the red LED may be lighted if one or a few ports are faulty. Check Error Log for relevant messages.
MAINTENANCE 2. 3. 4. If you hear dial tone, continue with this test. Dial the digits 1234567890 *#. Y OU should hear a DTMF signal as each key is pressed. If the test passes, you will hear dial tone within 1 to 3 seconds after you enter #. Repeat the test for each touch-tone receiver.
MAINTENANCE Procedures : 1. Make sure that the appropriate ZTN79 CP is translated. 2. Check for the presence of -48 volts at test point on front of cabinet. Symptoms: Inoperative used. Procedures : 1. If LOCAL display-equipped voice terminal when LOCAL button is button/lamp activate LOCAL button.
MAINTENANCE Figure 4-12. Clearing Virtual Facilities Troubles (Sheet 1 of 3).
MAINTENANCE Figure 4-12. Clearing Virtual Facilities Troubles (Sheet 2 of 3) 4-87.
MAINTENANCE Figure 4-12. Clearing Virtual Facilities Troubles (Sheet 3 of 3) 4-8 8.
MAINTENANCE Trunk Troubles Many trunk troubles originate in the central office (CO) facilities. The first step in identifying trunk troubles should be to check for presence of dial tone at the Trunk Access Equipment (TAE). If required, check the Error Log records, and make a trunk test call.
MAINTENANCE 5. Listen for dial tone from the accessed trunk. If dial tone is not present, isolate the fault to a trunk port CP or location in the trunk access equipment, etc., using a test set. 6. If dial tone is present, dial a working outside number.
MAINTENANCE 6. If “no loop current on outgoing call” is displayed, either of the above conditions could be true. It is more likely, however, that the facility is down . 7. Place an outside call on the line using the trunk test call procedures listed in outgoing Trunk Problems.
MAINTENANCE 8. 9. 10. 11. 12. If the problem does not move, replace the Ground Start CP. If the problem moves, the fault is with the CO. Notify CO personnel through the proper channels. If “Ringing no ground” is displayed, the T and R leads may be reversed in the trunk access wiring.
MAINTENANCE 3. 4. 5. 6. 7. 8. 9. ● CO failure to release after PBX disconnect ● CO belated release. These messages indicate CO problems. The first three errors are very common when DID trunks are installed. The CO should be notified through the proper channels about any of these problems.
MAINTENANCE Figure 4-13. Clearing Switched Loop Attendant Console Troubles (Sheet 1 of 5).
MAINTENANCE 4-13. Clearing Switched Loop 2 of 5) Console Troubles (Sheet 4-95.
MAINTENANCE Figure 4-13. Clearing Switched 3 of 5) Loop Attendant Console Troubles (Sheet 4-96.
MAINTENANCE 4-13. Clearing Switched 4 of 5) Console Troubles 4-97.
MAINTENANCE NOTES : 1. (a) System defaults to a DTAC when first powered up. (b) You have to remove the DTAC before you can administer the SLAC . (c) System 25 can support 1 or 2 DTAC or 1 or 2 SLAC but not a combination of both. 2. ID names can be assigned for PDCs, Trunks, FPDCs, and DGC groups.
MAINTENANCE Special Port Circuit Options for Stations and Trunks Tables 4-E and 4-F provide the special port circuit options that are administered in the system. System defaults and associated action codes applicable to the various port CPS are also shown.
MAINTENANCE Table 4-F. Applicable Actions for Circuit Pack Options ACTIONS FOR CIRCUIT PACK OPTIONS (See Circuit Pack Options—Table 4-E) CIRCUIT CP ACTIONS PACK TYPE 32 33 34 35 36 37 38 , ZTN76 GS .
6. 7. 8. 9. 10. 11. 12. 13. 14. If +7 volts are not present, the ADU is not receiving enough power from the data terminal and must be locally powered. If the ADU is powered from a local transformer, make sure that a 3- pair or 2-pair modular cord is connected between the transformer and the ADU.
MAINTENANCE Multiple Troubles or Trouble That Cannot Be Diagnosed Symptoms: Red LED is lighted on all port CPs. SAT displays this message: “FAIL : CPU : ARC H ANGEL INSANE: CHECK ZTN85: TERMINATOR?”. Procedures : 1. 2. 3. 4. 5. Check that the TDM bus terminator card(s) is installed in the rear pin field(s) .
MAINTENANCE Symptoms : Red LED is lighted cm several port CPs. Procedures: 1. 2. 3. 4. . Check the power supply to be sure that it is providing correct voltages (see “Power Supply Trouble’ ‘). Check the frontplane connector and the CPU/Memory CP, and replace any faulty unit(s).
REFERENCES The following System 25 documents are available for reference. A brief description of each manual is provided. ● Administration Manual ● Advanced Admin User Guide (MS-DOS) ● Advanced .
REFERENCES An Introduction to AT&T System 25 Provides an introduction to System 25 features and services. The emphasis is on how System 25 helps solve information management, productivity, and cost control problems. Implementation Manual Describes how to plan the system’s operating configuration.
REFERENCES Reference Manual This document is the system’s principal technical reference. It provides reference material for sales support, system configuration and operation, and for the system technician. It contains a comprehensive description of the system, emphasizing features, components and overall capabilities and capacities.
REFERENCES Call Management System—System Manual Provides information necessary to install CMS software, administer, use, and troubleshoot CMS. Call Management System—lnstallation Guide Provides instructions for inserting the CMS interface card into the PC.
ABBREVIATIONS AND ACRONYMS ABBREVIATIONS AND ACRONYMS ADU AE ARS ASCII BPS CCS CCSA COS CSU DCE DDC DDD DID DGC DS1 DTAC DTE DTMF DXS EIA ETU FNPA FRL FX HNPA Asynchronous Data Unit Account Executive .
ABBREVIATIONS AND ACRONYMS LD N Listed Directory Number LE D Light-Emitting Diode MET Multibutton Electronic Telephone MO H Music-on-Hold NA U Network Access Unit NE U Network Extension Unit NP A Numb.
APPENDIX A: APPENDIX A: System Wiring Tables Connector Pin Assignments Table A-A lists the lead designations and pin assignments at the 25-pair connectors on the system cabinets.
APPENDIX A: System Wiring Tables Table A-A. 25-Pair Connector Pin Assignments 25-Pin Corm. Cal l G S L S Tlp Ring ATL MET Backplane Pin No. Wir e Proc.
APPENDIX A: System Wiring Tables Table A-A. 25-Pair Connector Pin Assignments (Contd) 25-Pin Conn. DlD Tie Aux. Data Analog Analog TN767 Backplane Pin No. ‘ Wir e Trunk Trunk Trunk Lin e Line Line DS 1 Pin No. Color 3 TN760B TN763_ TN72 6 TM74 2 TN746B Interface (Slots 1-12) .
APPENDIX A: System Wiring Tables Table A-B. Building Wiring 25-Pair Cable 4-Pair Cable Term. Lead Functions 50 0 ATL 7101 A Cordless D-Inside D-Inside Cable Conn. Cable Conn. Ckt. 250 0 7300H RS-232C Color Pi n Color Block No. Series Series Term , code Num.
APPENDIX A: System Wiring Tables Table A-B. Building Wiring (Contd) 25-Pair Cable 4-Pair Cable Term. Lead Functions 50 0 ATL 7101A Cordless D-inside D-lnside Cable Conn. Cable Conn. Ckt. 250 0 7300 H RS-232C Colo r Pin Color Block No . Series Series Term .
APPENDIX B: APPENDIX B: Parts Listing The following information may assist you in cross-referencing Apparatus Codes, Comcodes and Price Element Codes (PECs).
APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE System 25 Control Unit (R1V2) 6250-012 include s Carrie r J58901A1 , L1 (e/w) Power Supply WP90510, L1 40395476 1 Fan Assembly WP90677,.
APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Upgrade Kit (R3V1/V2 to R3V3) R3V1/V2 Upgrade Kit 62527N * * CPU/MEM CP ZTN142 107057754 Circuit Packs GS Trunk CP LS Trunk CP TR Line .
APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Peripheral Equipment Digital Tape Unit 62507 TS-555A 404079436 System Admin. 62508 TI-703 404079428 Terminal (SAT) Voice Terminals and .
APPENDIX B: Parts Listing DESCRIPTION PEC MET Set-BIS Transformer Kit-of-Parts 12-button MET Set MET Adapter Cord 5-Button 7300H Ser VT 10-Button 7300H Ser VT 7300H Ser.
APPENDIX B: Parts Listing DESCRIPTION Acoustic Coupler Single-Line VT w/Message Light & Recall button Ground Start Key Mounting Bracket Ground Start Key External Alert Message Adjunct lROB Unit Mod.
APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Asynchronous Data Units ATL ADU 62506 D181521 includes 105105506 D8W-87 Cord (14ft) 103786802 Z3A5 ATL ADU 103975349 Mod/RS-232C(M) ADU.
APPENDIX B: Parts Listing DESCRIPTION PEC APPARATUS CODE COMCODE MOH Interface (Reg) 62517 KS-23395 10B ETU 62514 Emergency Trans Unit (2) B25A Cables DE D8W-87 Cord (7ft) Peripherals 62515 248B Adapt.
APPENDIX B: Parts Listing DESCRIPTlON PEC APPARATUS CODE COMCODE Cross-Connect Hardware Station interface Panel 2750-D28 617A 103982658 Mod/Mod Adapter 2750-D27 Z210A2 106308869 Mod/l 10 Adapter 2750-.
APPENDIX B: Parts Listing DESCRIPTlON Cables Octopus Cable (15 ft) Splitter Cable, Tie-Trk Splitter Cable, CO Trk Adapter (TN746) RS-232C X-Over Cable Cable Corm (15’ DE) CPU/MEM interconnect cable .
APPENDIX C: APPENDIX C: System Additions or Changes Additions and changes can be made to the system to support growth or changing needs of the customer. These system changes include: adding voice or data terminals, changing a voice-only connection to a voice/data connection, adding trunks, adding modems, and adding auxiliary equipment.
APPENDIX C: System Additions or Changes Table C-A. Unit Loads Port Type I Unit Load ZTN178 port I 0.5 TN742, TN746 1.0 port ETU 2.0 TN760B Port 2.0 TN753B Port 0.5 502-type Headset .75 Adapter 5-Button 1.0 Terminals Port Type Unit Load 10- and 34-Button 1.
APPENDIX C: System Additions or Changes 5. Insert the CP into the slot with the latch lever opened. Push it in firmly until you feel resistance and the latch lever moves toward its vertical position, flush with the edge of the CP. Push the lever all the vvay to vertical until the latch pin engages.
APPENDIX C: System Additions or Changes Figure C-1. Typical System 25 Port Circuit Pack C- 4 November 1995.
APPENDIX C: System Additions or Changes Set Option Switches on TN760B CP If the CP being added is a TN760B, use Figure C-2 and Table C-B to choose Figure C-2.
APPENDIX C: System Additions or Changes Table C-B. TN760B Option Switch Settings and Administration System 25 Installation Situation Circumstance Co-Located Inter-Bldg. . Co-Located Inter-Bldg. Co-Located Inter-Bldg. Co-Located To Sys25 DEFINITY Sys75/75XE Sys85 Sys25 DEFINITY sys75/75xE Sys85 DIMENSION PBX DIMENSION PBX Other Other Net Int.
APPENDIX C: System Additions or Changes Replace Circuit Pack Replace a CP if it fails or becomes damaged. 1. 2. 3. 4. 5. 6. Make sure that your hands are clean and dry. Put on a wrist grounding strap, and clip it to the grounding block at the back of the cabinet.
APPENDIX C: System Additions or Changes Add Cabinet Add a cabinet if all the slots in the existing cabinets are full and you need to add a CP. Also, if the addition of a CP to a cabinet will cause the unit load to exceed 80, a cabinet must be added. The system can support a maximum of three cabinets.
APPENDIX C: System Additions or Changes 6. 7. 8. 9. 10. 11. 12. 13. 14. Power down the system —all cabinets (Cabinet 1 last). Connect the cabinets, following the instructions under “Install System Cabinets” in Section 2. Connect a #6 AWG copper wire between the ground block of the new cabinet and the ground block of Cabinet 1.
APPENDIX C: System Additions or Changes Add Terminal 1. 2. 3. 4. 5. 6. Evaluate the cabinet unit power load using the procedures under “Evaluate cabinet unit Power Load” in this appendix. Check for available ports on checking the octopus cables the back of the cabinet.
APPENDIX C: System Additions or Changes Add Trunk 1. 2. 3. 4. 5. 6. If you are adding a DID or tie trunk, evaluate the cabinet unit power load using the procedures under Evaluate Cabinet Unit Power Load in this appendix.
Figure C-3. DS1 Network Interface Connections Replace Voice-Only Terminal With Terminal 1. 2. 3. 4. 5. 6. 7. 8. Using the Voice and Data Station Records Voice/Data Form (see “INSTALL EQUIPMENT ROOM STATION CABLING” in section 2), find the jack in the SIP adapter associated with the voice terminal that is to share a cable with.
APPENDIX C: System Additions or Changes 9. When the terminal is initialized, test it following the appropriate procedures in Section 3, “System Tests. ” Add Pooled Modem Circuit Pack 1. 2. 3. 4. Select a cabinet in which to add the TN758 Pooled Modem CP.
APPENDIX D: APPENDIX D: System Upgrades A D-kit-of-parts (PEC 62526N) k required to upgrade a Release 1 or a Release 2 system to a Release 3 V3 system.
APPENDIX D: System Upgrades 8. 9. 10. 11. 12. 13. 14. Remove the ZTN82 or ZTN128 Call Processor CP from slot 2 and discard (R1 only). Remove ZTN85 Service CP from slot 3 (R1 only) or slot 2 (R2 only) and replace with ZTN131 Service CP. (Put in slot 2.
APPENDIX D: System Upgrades 16. 17. 18. 19. Save the translations, and verify the accuracy of the backup tape. Refer to the Administration Manual for R3V1 (555-540-500) for these procedures. Install the front cover on Cabinet 1. Overlay the existing face plates on each switched loop console with the plates provided in the D-kit.
APPENDIX E: APPENDIX E: Administration Codes and Data The tables in this appendix are intended to help those familiar with system administration locate specific information without having to refer to the full text in the Administration Manual. Default values, if applicable, are indicated in bold print in these tables.
APPENDIX E: Administration Codes and Data Table E-B. PORT/PD. Administration, Voice Terminals (Menu=1/2) ACTION DESCRIPTlON DATA 0 Physical port number CSSPP** 1 Enter terminal type code [See Table E-C] 2 Enter PD.
APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd ) Administering the TN746B with Basic Administration Plug the TN746B into an unadministered carrier/slot location and warm start the System 25 .
APPENDIX E: Administration Codes and Data This page is intentionally blank E-2-b.
APPENDIX E: Administration Codes and Data Table E-B. PORT/PD. Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTlON DATA 17 Send ringing to bridged appearances [1=Y/0=N] when principal.
APPENDIX E: Administration Codes and Data Table E-B. PORT/PD. Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 46 51 52 53 60 90 10 0 10 1 Enable call waiting* [1=Y/0=N] Disp.
APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 100 Button to be assigned [button #] 101 PERSONAL LINE [3] If t.
APPENDIX E: Table E-B. Administration Codes and Data PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 AUTOMATIC INTERCOM [.
APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 SEND ALL CALLS [11] .
APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 ALARM [16 ] For types 309, 3.
APPENDIX E: Administration Codes and Data Table E-B. PORT/POC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 100 Button to be assigned [button #] 101 STAR T [24 ] For types.
APPENDIX E: Table E-B. Administration Codes and Data PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 JOIN [31 ] For type .
APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) ACTION DESCRIPTION DATA 10 0 Button to be assigned [button #] 10 1 BRIDGED ACCESS [37 ] If type 309, 310, or 311: NOT ADMINISTRABLE 102 PDC of Principal station [PDC ] NOTES: Cannot have a BA for a DTAC’s SA.
APPENDIX E: Administration Codes and Data Table E-B. PORT/PDC Administration, Voice Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 100 Button to be assigned [button #] 10 1 NEXT [41 ] Note: this feature requires the use of a DISPLAY voice terminal.
APPENDIX E: Administration Codes and Data Table E-C. Voice Terminal Type Codes If the Terminal Type is: Code: SINGLE-LINE VOICE TERMINALS: Without message waiting indicator 20 1 With message waiting i.
APPENDIX E: Administration Codes and Data Table E-D. Feature Button Translation (Menu=1/2) “Action=100” is required before action(s) 101-104 listed in this table are administered.
APPENDIX E: Administration Codes and Data Table E-D. Feature Button Translation (Menu=1/2) (Contd) "Action=100" is required before action(s) 101-104 listed in this table are administered ‘ Refer to page 10-6 of the Administration Manual.
APPENDIX E: Administration Codes and Data NOTES: A ? mark indicates that a yes/no If a (No) or (Yes) is present, response. 1) 2) 3) 4) 5) 6) 7) 8) 9) 1 0) 11) 12) 13) 14) 15) If Switched Loop Attendant Switched L OO p Attendant (1/0) response is required.
APPENDIX E: Administration Codes and Data Table E-E. Multiline Voice Terminal Button Defaults 7- SYS ACCESS 12- FLEX DSS 17- FLEX DSS 29- FLEX DSS 8- SYS ACCESS 13- ACCT ENTRY 18- FLEX DSS 30- FLEX DS.
APPENDIX E: Administration Codes and Data Table E-F. Switched Loop Attendant Console Button Defaults (Type 310) 7- LOOP† 8- LOOP† 9- LOOP† 10- LOOP† 11- LOOP† 12- ALARM† 17- LOCAL† 29- S.
APPENDIX E: Administration Codes and Data Table E-G. Switched Loop Attendant Console Button Defaults (Type 311 ) 7- LOOP† 12- ALARM† 17- lNSPECT† 29- SCROLL† 8- LOOP† 13- POS BUSY 18 - LOCAL.
APPENDIX E: Administration Codes and Data Table E-H. Direct Trunk Attendant Console Button Defaults (Cold-Start Defaults) 7- SYS ACCESS 8- SYS ACCESS 9- REP DIAL 10- REP DIAL 11- LAST # DIALED 12- FLE.
APPENDIX E: Administration Table E-1. Direct Trunk Attendant Console Defaults Installed Defaults) Codes and Data (Administration- 7- SYS ACCESS 12- FLEX DSS 17- 0 29- 0 8- SYS ACCESS 13- ACCT ENTRY 18.
APPENDIX E: Administration Codes and Data Table E-J. MET Set Button Defaults †Cannot be changed. E-22.
APPENDIX E: Administration Codes and Data Table E-K. PORT/PDC Administration, Data Terminals (Menu=12) ACTION DESCRIPTlON DATA 0 Physical port number CSSP P 1 Enter data type code [See Table E-K] 2 En.
APPENDIX E: Administration Codes and Data Table E-K. PORT/PDC Administration, Data Terminals (Menu=1/2) (Contd) ACTION DESCRIPTION DATA 67 Allow terminal to operate at a baud rate [1=Y/0=N] of 9600 bp.
APPENDIX E: Administration Codes and Data Table E-L. Data Port Type Codes IF THE DATA PORT TYPE IS CODE: I ( Dat a Lin e Card (DLC) 1801 functionality for ZTN126 or TN72 6 STAR LAN Interface Circuit 1.
APPENDIX E: Administration Codes and Data Table E-M. Port Administration, Trunks (Menu=1) ACTION DESCRIPTION DATA 0 Physical port number CSSPP 1 Enter trunk port type code [See Table E-N] 2 Enter trunk number [0001 -9999; 0001-0104] 3 Assign class-of-service code [(DID–1-4; 3) (All other— See Table E-O; 8)] 4 Assign pooled facility access code.
APPENDIX E: Administration Codes and Data Table E-M. PORT Administration, Trunks (Menu=1) (Contd) ACTION DESCRIPTlON DATA 12 For Switched Loop Attendant Systems [0-2; 0=either Att./ ONLY; Which attendant should receive 1=1st At. ONLY/ calls from this trunk?† 2=2nd Att.
APPENDIX E: Administration Codes and Data Table E-N. Trunk Type Codes If the Trunk Type is: Code: Ground Start, CO 701† Ground Start, WATS, FX 702 Ground Start, WPBX/Centrex 705 Loop Start, CO 801.
APPENDIX E: Administration Codes and Data Table E-O. Trunk Class-of-Service (for all trunks except DID) TRUNK CLASS-OF-SERVICE (FOR ALL TRUNKS EXCEPT DID) CO S NIGHT OUTWARD I N SHORT CODE SERVICE SIG.
APPENDIX E: Administration Codes and Data Table E-P. Port Administration, Auxiliary Equipment (Menu=1) ACTlON DESCRIPTlON DATA 0 Display physical port number, in the form CSSPP 1 Enter special feature port type code (see Table E-Q).
APPENDIX E: Administration Codes and Data Table E-P. Port Administration, Auxiliary Equipment (Menu-1 ) (Contd) ACTION DESCRIPTlON DATA 1 Assign voice Messaging Service port [260 - 263] type: 260 = standard voice mail services 261 = call coverage/auto-attendant 262 = message drop 263 = bulletin board 2 Assign PD for this VMS port [PD.
APPENDIX E: Administration Codes and Data Table E-Q. Special Feature Port Type Codes This table shows data values associated with Action=1 on Table E-P. Featur e TN742, ZTN7 8 TN763 ZTN7 6 ZTN77 TN748 TN758 ZTN7 9 Tone Detector External Alert 1st Page Zone 2nd Page Zone 3rd Page Zone nth Page Zone DGC Delay Ann.
APPENDIX E: Administration Codes and Data Table E-R. Port Options PORTS, Station/Trunk/Special Port Circuit Board Options FOR QUALIFIED SYSTEMS TECHNICIANS ONLY (See Table E-S, " Applicable Optio.
APPENDIX E: Administration Codes and Data Table E-S. Applicable Options See WARNING for Table E-R. Also note that a bullet in a box on this table indicates that the default value for that action (shown in Table E-R) is applicable for this circuit board.
APPENDIX E: Administration Table E-T. PDC Administration (Menu=2) Codes and Data ACTION DESCRIPTION DATA 0 Move this station to a new port [CSSPP (new port assignment)] (moved-to port must be vacant) 1 Display terminal type code [See Table E-C] 2-53 All other See note below.
APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) ACTION DESCRIPTlON DATA 3 Assign the number of rings before [Number of rings; 5] unanswered calls extended by Attend.
APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTION DATA 37 Specify type of dialing plan for Home [0=7-digit dialing; Area Code calls 1 = 10-.
APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTlON DATA 75 Change administration password (up to 8 ["8 characters or less”] printable.
APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTION DATA 89 Should this SLAC attendant (specified in [1=Y/0=N ] Action 88) receive a single-r.
APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTION DESCRIPTlON DATA 103 For Callback Queuing: Enter the [0-1 20; 30] minimum time (in seconds) between callback retries for outgoing facilities 110 For Remote Access: Enable barrier [1=Y/1=N] codes? 111 Assign DID remote access digits [PD.
APPENDIX E: Administration Codes and Data Table E-V. System Administration (Menu=4) (Contd) ACTIO N DESCRIPTlON DAT A I 130 Assign RIMS barrier code digits (5 [5 through 15 digits or 0 through 15 digits; 0-9, *, # to remove; 98765] 140 Sync. source” [0= Internal] [CSS of TN767=External 142 Enable automatic sync.
APPENDIX E: Administration Codes and Data Table E-W. Standard Call Type Defaults FOR SWITCHED LOOP SYSTEMS ONLY DEFAULT DEFAULT CALL TYPE CODE PRIORITY ATTENDANT (Action 91) (Action 92) (Action 93) Dial Attendant (0) Call Following - Logged to SLAC Non logged in FPDC Unassigned DID Attendant DID access code PD.
APPENDIX E: Administration Codes and Data Table E-X. Message-Center-Like Call-Type Defaults (effect of Action 90) FOR SWITCHED LOOP SYSTEMS ONLY DEFAULT DEFAULT CALL TYPE C0DE PRlORITY ATTENDANT (Acti.
Table E-Z. Direct Group Calling (DGC) Administration (Menu=6) ACTION DESCRIPTlON DATA 1 2 3 11 12 13 14 20 21 51 52 53 Assign a DGC access code (0 to delete an existing DGC access code) For data DGC g.
APPENDIX E: Administration Codes and Data Table E-AB. DGC Announcement Administration ACTION DESCRIPTION DATA 1 DGC Announcement 25 5 2 PD C [Unique PDC] 3 Dial Restricted [1=yes, 0=no (default)] 90 A.
APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) ACTION DESCRIPTION DATA 1 Search for PDCs of call coverage [1] sender s 2 Call coverage receiver group [1-32 or 10.
APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) (Contd) ACTION DESCRIPTION DATA 1 Search for PDC of pickup grou p [9 ] member s 2 Pickup group number [1-16] 1 Sea.
APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) (Contd) ACTION DESCRIPTION DATA 1 Search for button location on a station [20 ] 2 PDC of station with buttons [PDC.
APPENDIX E: Administration Codes and Data Table E-AC. Searches: Action Items (Menu=8) (Contd) ACTION DESCRIPTION DATA 1 “Given number, get Display ID” search [40 ] (PDC, DDC, FPDC, or DGC access ,.
APPENDIX E: Administration Codes and Data Table E-AD. Board Type—Wildcard Representation CATEGORY: BOARD DESCRIPTION: DATA: Empty Empty Slot (Searches 15 & 17 only) 0 Station Single-line Voice Terminal or Special Port 2 . . MERLIN CS Voice Terminal or Attendant 3.
APPENDIX E: Administration Codes and Data Table E-AE. Port/Board Type—Specific Representation CATEGORY: DESCRIPTION: DATA: Voice Station SINGLE-LINE VOICE TERMINALS: Without message waiting indicato.
APPENDIX E: Administration Codes and Data Table E-AE. Pod/Board Type—Specific Representation (Contd) CATEGORY: DESCRIPTION: DATA: Voice Station (Contd) ATTENDANT VOICE TERMINALS: Direct Trunk Attend.
APPENDIX E: Administration Codes and Data Table E-AE. Port/Board Type—Specific Representation (Contd) CATEGORY: DESCRIPTION: DATA: Trunk (Contd) Delay Dial-in/Auto-out 100 7 Delay Dial-in/Delay Dial.
APPENDIX E: Table For Action=1, Administration Codes and Data E-K Save/Restore and System Restarts (Menu=9) you need to press the PLAY and RECORD buttons.
APPENDIX E: Administration Codes and Data Table E-AG. RS232 Port Administration (Menu=10) In response to "RS232=", enter the RS232 connector (1-5*) to be administered.
APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=1) ACTION DESCRIPTION DATA 10 0 Assign a pattern number [1-8 ] 10 1 Assign a start time for subpatt.
APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=11) (Contd ) ACTION DESCRIPTION DATA 23 0 Assign Route 3 for subpattern 1 B (a [FAC or VFC] facilit.
APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=11) (Contd ) ACTION DESCRIPTlON DATA 60 1 Assign a 7-digit emergency telephone [7-digit number] num.
APPENDIX E: Administration Codes and Data Table E-AH. Automatic Route Selection Administration (Menu=11) (Contd) ACTION DESCRIPTlON DATA 900 N11 CO exchange for which a pattern [N11 code] is being ass.
APPENDIX F: Administration Error Messages APPENDIX F shows Basic Administration error codes and descriptions. The Advanced Administration system uses different terminology. For additional details about an error message in Basic Administration, press the “?” key.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1006 : incorrect entry Cabinet-Slot-Port (CSSPP) PP must port-on-board number out be a number from 1 to 8 (varies on of range different circuit packs) 1007 : incorrect action number Must administer ACTION = 1 before can ‘t exceed 1 with proceeding.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTlON POSSIBLE SOLUTION 1017 : inappropriate request Cap already installed system already has Direct CA P ACTION = 1 (Cap) Go to MENU .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTlON 1031 : at installed max At system maximum of 12 touch- -12 Touch-Tone tone receivers. Receiver s 1032 : at installed max At system maximum of 8 external -8 external alert alert s 1033 : at installed max At system maximum of 3 paging -3 paging zones zones .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1044: inappropriate request Neither primary nor secondary CAP primary or secondary CAP universal port number agrees with the unavailable one stored by admin. on the stack.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1056 : inappropriate request Trying to administer something other must be virtual facility than a Virtual digit. [0-9, *, #] Must be a Virtual Facility. 1057 : at installed max Group or button maximum reached.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION 1069 : incorrect facility type incompatible with board typ e 1070 : facility type out of range must be 3-4 digits POSSIBLE SOLUTION Board and features do not mix. Check slot location for correct board or not compatible with the already entered types on the board.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1083 : inappropriate request Recheck translations to see if TT TT generator not installed generator was installed. 1084: inappropriate request Trying to administer a third CAP system already has two when you are only allowed two.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 1094: inappropriate request Display attendant position only DISPLAY of SLC- DTAC/SLAC.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2003 : incorrect button number Check button range for station type. out of range for ATL set 2004 : inappropriate request Cannot administer button features EMT can’t have button on an EMT station or not allowed for particular type of service.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2026 : incorrect entry Check to see if trunk is trunk does not exist administered. No such trunk ID. 2027 : inappropriate request Cannot assign night service to a not optioned for night DID trunk.
APPENDIX F: Administration Error Messages ERROR MESSAG E AND DESCRIPTION POSSIBLE SOLUTION 2039 : inappropriate request Cannot assign buttons that are buttons fixed- can’t already fixed on the CAP. assig n 2040 : incorrect PDC Has to be an ATL station to assign must be station for prime prime line preference.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2053 : incorrect entry Area Code = NPA incorrect area code office where N=2-9, P=0-l ,and A=l -9. cod e Office Code = NXX where N=2-9, X=0- 9 Invalid area code or office code for Toll Calls Allowed.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2074: inappropriate request Check Home Area Code/Toll Call office code exists-list 1 Allowed list to see if office code exists in list 1. Added office code to pattern already .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 2082 : inappropriate request See: MENU = 7 (TCA) superset exists-list 1 ACTION = 2 Trying to add a number to a TCA list that already exists in another list. In this case, the superset is used in conjunction with wild card characters .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 208 9 entry out of range ARS Facility Level = O-3. facility restriction level exceeded 2090 : inappropriate request Single line stations are defaulted station not allowed speed personal speed dialing.
APPENDIX F: Administration Error Messages ERROR MESSAGE I AND DESCRIPTION POSSIBLE SOLUTION 3015 : at installed max Can install 16 trunk group -pool groups maximum . 3016 : entry out of range Only 1 digit can be entered for the access code must be 1 trunk pool dial access information.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 4001 : entry out of range Maximum FPDCs = 300 FPDC max reached 4002 : incorrect entry Specified FPDC not found. does not exist or used improperly 4003 : action number out of Must do action 1 before removing sequence FPDC .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 5013 : incorrect entry Da y = HHMM where HH=00-23 incorrect hours data 5014 : incorrect entry Day = HHMM where MM= 00-59 incorrect minutes data 6000 : incorrect entry Check search type in admin.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 6016 : incorrect facility type The subtype number is the entered subfacility type out of type is too large for the facility rang e specified. 6017 : incorrect entry Traffic register number given is out number out of range of range .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7005 : incorrect entry Entered data not valid for restricting incorrect data to restrict PBX calls. PBX call s 7006 : incorrect entry Number of seconds before a data can’t exceed 120 camped on call returns to the attendant console [1-1 20].
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7023 : incorrect entr y Data value cannot exceed 1. data can’t exceed 1 7026 : incorrect PDC Must be station or data port. must be station or data port 7027 : incorrect entry Entry cannot be 0 or exceed 5 can’t be 0 or exceed 5 digits.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7037 : inappropriate request Direct Group Calling Delay announcement group Announcement (1 per system).
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7047 : incorrect PD C Can verify that the PDC is not in a not in any DGC group DGC group by : Go to MENU = 8 S.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7054 : out of space System speed digit pool is full. no more room in digit poo l 7200 : entry out of range Invalid TARGET value specification. RS232 value out of range Target value should be 1-4.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 7401 : incorrec t MENU = 10 (RS-232) TARGET = 1 entr y ACTION = 1 DATA = 1 or 4 data must be 2 or 3 (Reassign RS232 connector) NOTE: Above statement is wrong. data must be 1 or 4 only 8000 : incorrect action number A blank space is not acceptable.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8111: incorrect entry trunk pool does not exist Check the original trunk pool entered against the ARS trunk pool you are trying administer . 8112: action number out of rang e number must be 0-1 Only 1 and 0 are valid entries for DDD overflow in ARS.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8402 : entry out of range The list number range is between list reference can’t 1-4 . exceed 4 8403 : entry out of range The pattern range is 1-8 or 0 for must be 0-8 for removal removal.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8418 : entry out of range MENU = 11 (ARS) ACTlON = 501 list member must be 1 DATA = 1 digit value, 1-8 range. digit; value 1-8 8419 : inappropriate request All members of the list have already all members of list were been displayed.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8429 : inappropriate request The telephone number cannot be phone number exists-list removed because it’s installed in list 3 3 .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 8700 : action number out of Must enter pattern number first. sequenc e must enter pattern number first 8701: incorrect action number Go back and verify the action item does not exist or used taken .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 9003: inappropriate request MENU = 1 (Port) under Special station to be linked not Feature port. installed ACTION = 1 DATA = 253 ACTION = 2 DATA = PDC or 0 In this case, the PDC is invalid or does not exist.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION I 9025 : inappropriate request Removal of a station is disallowed if sole member of queued for the station happens to be the only DGC group member of a DGC group that is being queued for.
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 9035 : inappropriate request All Agent buttons that are in the same Agent buttons must be on linked-list must be on the same same station station .
APPENDIX F: Administration Error Messages ERROR MESSAGE AND DESCRIPTION POSSIBLE SOLUTION 904 7 Incorrect entry. Must be CSS or 0. 9048 Cannot change board type Untranslated or (and) remove board via the HI D CKT menu. first . 904 9 Invalid TN or ZTN code for Use correct code to set board options the HI D CKT menu.
GLOSSARY GLOSSARY The following is a list of definitions of terms used in System 25 documentation. Administe r To access and change the parameters associated with the services or features of the system. Analog Data Endpoint Data endpoints connected to the system by (built-in or stand-alone) modems.
Attendant The operator of the attendant console. Attendant Console ● Direct Trunk Console: An electronic call-handling position with pushbutton control.
GLOSSARY Buffe r A circuit or component that isolates one electrical circuit from another. Typically, a buffer holds data from one circuit or process until another circuit or process is ready to accept the data.
GLOSSARY Central Office Codes The first three digits of a 7-digit public network telephone number. These codes are numbered from 200 through 999 and are sometimes referred to as NNXS. Central Office Trunk A telecommunications channel that provides access from the system to the public network through the local central office (CO).
GLOSSARY Covering User The person at an alternate answering position who answers a redirected call. Data Channel A communications path between two points used to transmit digital signals. Data Communications Equipment (DCE) Refers to a specific RS-232C interface connector configuration.
GLOSSARY Delay-Dial Tie Trunk Digital Digital After a request for service (called a seizure) is detected on an incoming trunk, the system sends a momentary signal followed by a steady tone over the trunk. This informs the calling party that dialing can start.
GLOSSARY Dual-Tone Multifrequency (DTMF) Industry terminology for touch-tone calling. Emergency Transfer Unit (ETU) Provides direct connection of designated Power Failure Transfer (PFT) registered voice terminals to the CO during a power failure or other service interruption.
GLOSSARY Facility By technical type these include loop-start, ground-start, DID, data, and automatic ringdown trunks. These facilities may be accessed by their facility access codes (FACS). Restriction Level (FRL) A restriction parameter associated with the Automatic Route Selection (ARS) feature.
GLOSSARY Ground-Start Trunk On outgoing calls, System 25 transmits a request for service to the distant switching system by grounding the trunk ring lead. When the distant system is ready to receive the digits of the called number, that system grounds the trunk tip lead.
Loop-Start Trunk Modem Modem Simplest type of central office (CO) trunk. Calls are originated by providing a dc path between the tip and ring leads. The CO detects the loop current thus drawn and returns dial tone. Incoming calls are signaled by the CO placing an ac ringing voltage between the tip and ring leads.
GLOSSARY Number Plan Area (NPA) The area code. Off-Premises Station (OPS) An arrangement provided by the local telephone company permitting remote terminal equipment to operate as though it were directly connected to the system. This tariffed service can be provided only for FCC-registered single-line voice terminals.
GLOSSARY ● Floating— Assigned to visitors who will be moving about the premises. Floating PDCs may be associated with the attendant position or may be “logged in” by the user at any voice terminal. Calls to the floating PDC will ring at the terminal where “logged in.
Protocol A set of conventions or rules governing the format and timing of message exchanges to errors . Public Network The network that can be or long-distance calling. Queu e control data movement and correction of openly accessed by all customers for local An ordered sequence of tasks to be processed.
GLOSSARY Reorder Ton e Atone repeated 120 times a minute; indicates that at least one of the facilities, such as a trunk or a digit transmitter, required for the call is not available.
GLOSSARY Switch The software-controlled communications processor complex that interprets dialing pulses/tones/keyboard characters and makes the proper interconnections both within the system and outside the system.
GLOSSARY Terminal Equipment Equipment used to change information (sound, keystrokes) into an electrical signal compatible with System 25’s port circuits. (Voice and data terminals are the two primary types.) Tie Trunk A telecommunications channel that directly connects two private switching systems.
GLOSSARY Trunk Group Telecommunications channels assigned as a group for certain Trunk Port The hardware (circuit pack) providing an interface between the system and central office (CO)/network trunks. Unit Load A measurement used to evaluate a System 25 cabinet’s power load capacity.
INDEX INDEX 617A Panels 2-6 617A Panels Install 2-44 7300H Series Terminals 2-73 Voice Terminal Tests 3-3 7300H Series Voice Terminal Tests 3-3 A Abbreviations 6-1 Acronyms 6-1 Adapters Description 2-.
INDEX Cables B-10 C-Type Connector 2-12 Description 2-11 octopus 2-72 Splitter 2-11 Cabling Add C-3 Call Coverage Test 3-8 Call Management System—installation Guide 5 4 Call Management System—Plan.
INDEX DTU (Continued) Operation 4-14 DTU Troubles 4-81 E Emergency Transfer 2-77, 4-4 Install 2-77 Test 3-15 Unit Trouble 4-80 Equipment Auxiliary B-7 Peripheral B-4 Test 4-2 Equipment Room 2-16 Stati.
INDEX Install (Continued) SIP 2-4 4 SMDR 2-111 TAE 2-44 Terminals 2-87 Install STARLAN NETWORK Interface 2-112 Installation 2-1 system 2-1 Installation and Maintenance Manual 5-2 Integrated Solution U.
INDEX Panels (Continued) 617A 2-6 Parts B-1 ADUs B-7 Auxiliary Equipment B-7 Cabinets B-1 Cables B-10 Circuit Packs B-3 Connector Blocks B-9 Cords B-10 Cross-Connect Hardware B-9 Peripheral Equipment .
INDEX S SAT 4-6 Connection 2-102, 2-104, 2-706, 2-109 Install 2-102 SAT Troubles 4-81 Selector Console Test 3-9 Service Telephone Number 4-9 Single-Line Voice Terminal Tests 3-5 Single-Line Sets 2-74 .
INDEX Terminal (Continued) System Administration 4-6 Terminal Operations Manual 5-3 Terminals Add C-10 Install 2-87 Voice B-4 Test Equipment 2-2 Test Equipment 4-2 Test Points 4-6 Tests 7300H Series V.
INDEX U Undiagnosable Troubles 4-102 Upgrade Kit (Rl or R2 to R3) B-2 Upgrade Kit (Rl to R2 to R3] Parts B-2 Upgrades System D-1 User Guides (700 Series) V Voice Terminal Labels 2-88 Tests 3-5 Voice T.
デバイスADTRAN 25の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
ADTRAN 25をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはADTRAN 25の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。ADTRAN 25の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。ADTRAN 25で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
ADTRAN 25を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はADTRAN 25の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、ADTRAN 25に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちADTRAN 25デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
