Bush HogメーカーATH 720の使用説明書/サービス説明書
ページ先へ移動 of 20
ASSEMBLY l l OPERATION l l MAINTENANCE 04/09 Rev.1 $4.00 90898 A A T T H H / / F F T T H H A A i i r r T T u u n n n n e e l l & & F F l l a a t t D D e e c c k k F F i i n n i i s s h h i i n.
CONGRATULATIONS! You have invested in the best implement of its type on the market today. The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life.
ATH / FTH FINISHING MOWER Operator’s Manual TABLE OF CONTENTS SECTION/PARA PAGE Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .2 Dealer Preparation Check List . . . . . . . . .3 Safety Precautions . . . . . . . . . . . . . . . . . .4 Federal Laws and Regulations .
LIMITED WARRANTY OOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free fro.
DEALER PREPARATION CHECK LIST ATH / FTH FINISHING MOWERS BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator’s Manual as a guide. o 1. Assembly completed. o 2. Gearboxes filled with oil. o 3. All fittings lubricated.
IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safety p r e c a u t i o n s t h a t s h o u l d b e f o l l o w e d b y t h e operator to avoid accidents. When you see this symbol, carefully read the message that fol- lows and heed its advice.
IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- t o m e r . Y o u r A T H / F T H S e r i e s R o t a r y C u t t e r h a s been carefully designed to give maximum service with minimum down time.
2-1 ATTACHING TO TRACTOR A. Attach to tractor Cat. I three point hitch as described in tractor operator’s manual. SECTION II PREPARATION FOR USE B. Raise and lower cutter to determine position with shortest distance between the tractor PTO shaft and gearbox input shaft.
G. Clamp end of driveline in a vice. Cut off shield where marked. (Figure 2-3). Figure 2-3 H. Using cut off section of shield as a guide, cut shaft the same amount. (Figure 2-4) I. Repeat steps “G” and “H” to other driveline sec- tion. J. Deburr ends of driveline sections and clean away all chips and filings.
SECTION III OPERATING INSTRUCTIONS 3-1 GENERAL SAFETY Only qualified people familiar with this operator’s manual and tra ctor operator’s manual should oper- at e th is m ac hi ne . Op er at or s ho u ld w ea r har d ha t , safety glasses and safety shoes.
SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower implement to gro und, turn off tractor, and set parking brake before doing maintenance inspections or work. Some checks may require raising machine off ground and supporting with blocks.
4-3 BELT ADJUSTMENT Belt tension should be checked every 40 hours to get maximum life from drive belt and best perfor- mance from cutter. Belt tension is adjusted by increasing or decreasing the length of the spring on the moveable idler. For proper belt tension on the 48” mow er, t he s pring leng th s hould be set a t 7- 1/16” .
4-6 TROUBLESHOOTING Troubleshooting procedures are listed in Table 4-1 below. If the problem cannot be solved or replacement parts are necessary, contact your authorized Bush Hog dealer. Please have ready your machine name, model num- ber, serial number, purchase date and exact cause or description of problem.
THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TH OROUGHLY UNDERSTOOD BEFORE ATTEMPTING MACHINE ASSEMBLY. 1. Wear personal protective equipment such as, but not limited to, protect ion for eyes, ears, feet, hands, lungs and head when assembling the equip- ment.
D. Loosely attach two caster arms to the front of the mower deck using 5/8 x 3-1/2” bolts, lockwash- ers and hex nuts. Install reinforcement plates between bolt heads and caster arms. Loosely attach the remaining two caster arms to the rear of the mower deck using 5/8 x 3-1/2” bolts, lockwashers and hex nuts in each caster arm.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog wi ll, upon request, provide safety decals for any of our products in the field at no charge.
BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 U.
.
2501 Griffin Ave. l l Selma, AL 36703 Telephone (334) 874-2700 l l www.bushhog.com.
デバイスBush Hog ATH 720の購入後に(又は購入する前であっても)重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります:
Bush Hog ATH 720をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはBush Hog ATH 720の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Bush Hog ATH 720の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Bush Hog ATH 720で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Bush Hog ATH 720を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はBush Hog ATH 720の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Bush Hog ATH 720に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちBush Hog ATH 720デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。