C.ItohメーカーEZ-DT4の使用説明書/サービス説明書
ページ先へ移動 of 44
User’s Manual EZ-DT-2 / EZ-DT-4 P/N. 920-012511-03 Rev. A, 08.2009.
Safety Instructions Bitte die Sicherheitshinweise sorgfältig lese n und für später aufheben. 1. Die Geräte nicht der Feuch tigkeit aussetzen. 2. Bevor Sie die Geräte ans Stromnet z ansc hließen, verge wissern Sie Sich, dass die Spannung des Geräts mit der Netzspan nung übereinstimmt.
Safety Instructions Please read the following instruction s seriously. 1. Keep the equipment away from humidity. 2. Before you connect the equipment to the power outlet, please check the voltage of the power source. 3. Disconnect the equipment from the volta ge of the power source to p revent possible transient over voltage damage.
1. BARCODE PRINTER ................................................................... 4 1-1. Printer Accessories ......................................................................................................... 4 1-2. General S pecifications .
1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the acce ssorie s that come with the p ackage, and store appropriately. Barcode printer Power cord Switching Power USB Cable Label Quick Start Guide CD (includes label editing software QLabel / Manual) EZ-DT-2 EZ-DT-4 1-2.
Download Fonts Bitmap fonts 90°, 180°, 270° rotatable, single ch aracters 90°, 180° , 270° rotatable A sian fonts 90°, 180°, 270° rotatable an d 8 times expandable in horizontal and vertical .
1-3. Communication Interface Serial Interface Serial Default Setting : 9600 baud rate ､ no parity ､ 8 data bits ､ 1 stop bit ､ XON/XOFF protocol and RTS/CTS 。 RS232 HOUSING (9-pin t o 9-pin).
1-4. Printer Parts 2 4 1 5 3 1. LED Light 2. FEED Key 3. Top Cover 4. Power Switch 5. Cover Open Button 1 2 3 6 5 4 1. Print Head Lift 2. Label Roll Holder 3.
3 2 1 1. Platen Cover 2. Label Sensor 3. Platen Roller 1 3 2 4 1. Power Socket 2. USB Port 3. Fan-Fold Label Insert 4. Serial Port (RS-232) 1 2 1. Bottom Case Cover 2.
2. Printer Installation 2-1. Label Installation 1. Place the printer on a horizontal surface and open the Top Cover. 2. Press and release the lock of Label Roll Core. 3. Pull up the Label Roll Holder and lift the Label Roll Core upward. 4. Place a new label roll onto the Label Roll Core.
7. Put the label under the Label Guide and stretch it frontward. 8. Pull the Label Guide inward and make it fit the edge of label. 9. Close the Top Cover to complete the label installation.
2-2. Label Roll Core Switch 1. Pull the Label Roll Holder to the topmost and lift the Label Roll Core upward. 2. Turn the Label Roll Core outward as the figure shows. 3. Whirl the Label Roll Core back to the original position. 1” Core A. When the lock hole of Label Roll Core is on upper side, it applies to 1” core.
2-3. PC Connection 1. Please make sure the printer is powered off. 2. Take the power cable, plug the cable sw itch to the po wer socket, and then connect the other end of the cable to the printer power so cket. 3. Connect the cable to the USB/ Serial port on the printer and o n the PC.
2-4. Driver Installation 1. Insert product CD to your computer’s CD Drive and find the "Windows Drives" folder. 2. Select the icon of driver file and click it to start the installation. 3. Follow the instruction on screen to keep the installation going.
6. Select connection port. 7. Enter the printer name and set printer sharing option. 8. A description page of printer settings will be displayed after all settings are completed. 9. Check if all printer settings are correct and then press Finish to start copying driver files.
3. Accessory 3-1. Stripper Module Installation 1 Stripper Module 2 Screw x 2pcs 【 Note1 】 Please power off the printer before installing the stripper module. 【 Note2 】 Label liner thickness is recommended to be 0.0 6mm ± 10% with basic weight 65g/ ㎡ ± 6%.
EZ-DT-4 EZ-DT-2 5. Turn the printer around and tighten screws to fix the Stripper in location. 5. Loose the screw of Bottom Case Cover and open it. 6. Unlock the Bottom Case Cover to see the main board of printer. 【 Note 】 You can also use coin o r screwdriver to open the bottom case cover.
10. Flip the stripper downwa rd to open it. 11. Follow the instruction on Chapter 2-1 to install the label. 12. Peel off the first label, and feed the liner through the roller and the strip bar. 【 Note 】 The label / paper used for stripper is suggested to be at least 20mm in height.
3-2. Cutter Module Installation 1 Cutter Modul e 2 Scr e w x 2pcs 2 1 【 Note1 】 Please power off the printer before installing the cutter module. 【 Note2 】 Do not cut self-adhesive la bels! Th.
Z-DT-4 E EZ-DT-2 5. Turn the printer around and tighten sc o rews t fix the Cutter in location. 5. Loose the screw of Bottom Case Cover and open it. 6. Unlock the Bottom Case Cover to see the main of r. board printe 6. Tighten the screws to fix the Cutter in location.
3-3. EZ-DT-2 t Module Installation Ethernet Ca Etherne ble 1.8M 1 2 Module Connection Wire 3 Bracket 4 Ethernet module 5 Ethernet Back Panel 6 Bracket Screw*2 7 Secure Screw*2 【 Note 】 Please make sure that anti-static precautions are adopted during the installation.
8. Unscrew the Ground wi re screw and r re. emove the Ground wi 9 screws on both side s of . Loosen hexagonal RS-232 port. 10. Remove Standard Back Panel and change it with Ethernet Back Panel. 11. Tighten the hexagonal screws. 1 2 12. Secure the Ethernet module onto the bracket.
16. Plug the connector of the M odule Connection Wire into the so cket on Ethernet module. 17. Use power co nnector cable to push all connection wires that o n the right side of mainboard to lean against the wall of bottom case. 18. Plug the power connector into the mainboard.
3-4. EZ-DT-4 Ethernet Module Installation 1 Ethernet module 2 Ethernet Back Panel 3 Module Connection Wire 4 Secure Screw*1 5 Ethernet Cable 1.8M 1 2 3 5 4 【 Note 】 Plea e make sure that anti-static p recautions dopted during the installation. s are a 1.
9. Install the Ethernet Back Panel to the printer. 10. al 11. screws. Push the mainboard back to origin position. Tighten the hexagonal 12. Align the Ethernet module to the Ethernet port and plug into it. 3. Tighten the secure screw to fix Ethernet 1 module onto the main board.
4. Printer Setting 4 After pre f eed the media (according to media type) to the s ith c ontinuous media, pressing the FEED key will feed the media out printing with labels, the printer will feed one lab el each time the FEED key is pressed. If the label is not sent out in a correct position, please proceed with the Auto Sensing (see next section).
4-4. Self-Test The Self-Test page helps user to figu re out whether the printer is operating n ormally. Below are ns about the content of Self-Test page: 【 Note 】 For more information about advance settings, such as "Sen refer to Programmer's m anual.
4-5. Error Messages LED Light Beep Description Solution Red (Flash) None Print head temperature high. Wait for the print head temperature drops to the normal temperature range, printer will go back to the standby mode ED light will stop and the L flashing.
5. Maintenance and Adjustment 5-1. Print Head Module Installation / Remo 1. Open the top cover e the d Lift, w on the left side of Top Cover. 【 Note 】 Po ff th before remo installing the print head. val Instruction to se Print hich is Hea wer o e printer ving or 2.
5. Remove the Print Head Screws, 6. From the underneath of the Print Head Bracket, 7. After new print head is installed, tighten the Print Head Screws, plug the re ft to complete the installation. hold the front end of print head to remove it and install new print head.
5-2. Thermal Print Head Cleaning Uncle y be caused by dusty print head, ribbon stain or label line r glue. Therefore when printing, it’s nece ssary to keep the top cover closed. Also, check and prevent paper/label from being stained or dusty to ensure print quality and to prolong the print head life.
5-4. Black Mark Paper W aper width is equal to the maximum width of p 18mm for EZ-DT-4), the error may occur since the b e detected by senso r sometimes.
5-5. Troubleshooting Problem Recommended Solution LED light does not light up after power on the printer Check the powe r connec tor LED light indicates error messages after Check for sof twar.
Appendix 1. EZ-DT-2 Certifications EZ-DT-2/EZ-DT-4 User’s Manual 33.
EZ-DT-2/EZ-DT-4 User’s Manual 34.
EZ-DT-2/EZ-DT-4 User’s Manual 35.
EZ-DT-2/EZ-DT-4 User’s Manual 36.
EZ-DT-2/EZ-DT-4 User’s Manual 37.
2. EZ-DT-4 Certifications EZ-DT-2/EZ-DT-4 User’s Manual 38.
EZ-DT-2/EZ-DT-4 User’s Manual 39.
EZ-DT-2/EZ-DT-4 User’s Manual 40.
EZ-DT-2/EZ-DT-4 User’s Manual 41.
EZ-DT-2/EZ-DT-4 User’s Manual 42.
EZ-DT-2/EZ-DT-4 User’s Manual 43.
デバイスC.Itoh EZ-DT4の購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
C.Itoh EZ-DT4をまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはC.Itoh EZ-DT4の技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。C.Itoh EZ-DT4の取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。C.Itoh EZ-DT4で得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
C.Itoh EZ-DT4を既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はC.Itoh EZ-DT4の不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、C.Itoh EZ-DT4に関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちC.Itoh EZ-DT4デバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
