Cabletron Systemsメーカー9A656-04 ATM Moduleの使用説明書/サービス説明書
ページ先へ移動 of 44
9032031-01 SmartSwitch 9500 9A656-04 ATM Module Hardware and Installation Guide.
.
i Notice Notice Cabletron Systems r eserves the right to make changes in speciÞcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletr on Systems to determine whether any such changes have been made.
Notice ii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference r eceived, including interference that may cause undesir ed operation.
iii Notice Dec laration of Conf ormity Application of Council Directive(s): 89/336/EEC 73/23/EEC Manufacturer Õs Name: Cabletron Systems, Inc. Manufacturer Õs Address: 35 Industrial W ay PO Box 5005 Rochester , NH 03867 European Repr esentative Name: Mr .
Notice iv.
v Contents Chapter 1 Intr oduction Document Objectives .................................................................................................... 1-1 Overview ..................................................................................
Contents vi Chapter 4 LANVIEW LEDs ANIM LEDs ............................................................................................................ 4-3 Chapter 5 General Specifications Operating SpeciÞcations ..................................
1-1 Chapter 1 Intr oduction Document Objectives This document, the SmartSwitch 9500 9A656-04 A TM Module Hardwar e and Installation Guide , contains introductory , installation and speciÞcation information for the support of the 9A656-04 SmartSwitch Module.
Introduction 1-2 Overview The 9A656-04 (shown in Figure 1-1) is a 4.5 Gbps, single slot module for the SmartSwitch 9500 chassis. Up to four A TM Network Interface Modules (ANIMs) of any type can be plugged into the 9A656-04 to provide fr ont panel connectivity to the network.
1-3 Ov er view Figure 1-1. The 9A656-04 AN AN AN AN 2031_01.
Introduction 1-4 Features The features of the 9A656-04 ar e described in the sections below: Pr ocessor The 9A656-04 is equipped with an advanced Intel i960 micropr ocessor . This micropr ocessor provides signalling, SNMP management, and serves as the in-band management LAN Emulation Client (LEC).
1-5 Related Manuals LANVIEW LEDs The 9A656-04 uses LANVIEW , The Cabletron Systems built-in visual diagnostic and status monitoring system. W ith LANVIEW LEDs, you can quickly identify the device, port, and physical layer status at a glance.
Introduction 1-6 Getting Help For additional support related to this de vice or document, contact the Cabletron Systems Global Call Center: Before calling the Cabletron Systems Global Call Center , ha.
2-1 Chapter 2 Installing the 9A656-04 Module SmartSwitch 9500 modules can be installed in any of the slots that are available. T o install a module, proceed as follows: 1. Remove the blank plate covering the slot in which the 9A656-04 will be installed.
Installing the 9A656-04 Module 2-2 Figure 2-1. Installing the 9A656-04 2031_02 AN AN AN AN Circuit Card Card Guides Metal Back-Panel Plastic Locking T ab Plastic Locking T ab.
2-3 The Reset Switch The Reset Switch The Reset switch is located on the front panel, under the top plastic tab as shown in Figure 2-2. It serves two functions: ¥ Pressing the Reset switch twice within thr ee seconds causes the processor (i960) to reset.
Installing the 9A656-04 Module 2-4 The Module Car d DIP Switch An eight position DIP switch is located on the module car d as shown in Figure 2-3. The functions of the switches ar e listed in T able 2-1. ! CA UTION Do not toggle Switch 8 unless you intend to reset the user configured pass words to their f actor y default settings .
2-5 Installing an ANIM Installing an ANIM Figure 2-3 shows the location of the 4 motherboar d connectors, and the 16 standoff scr ews for the A TM Network Interface Modules (ANIMs). Figure 2-3 also shows the location of the Module Card DIP Switch. Figure 2-3.
Installing the 9A656-04 Module 2-6 The 9A656-04 module is shipped without ANIMs. T o install the ANIMs proceed as follows: 1. Remove the module if it is installed in the SmartSwitch 9500 chassis. T o remove a module, r elease (rotate outwar d) the top and bottom plastic locking tabs, then slide the module out of the chassis.
2-7 Installing an ANIM 5. Press straight down Þrmly on the ANIM until the pins slide all the way into the motherboard connector . Ensure that the ANIM seats ßush on the standoffs. 6. Secure the ANIM with the two screws saved in step 2 and the two screws supplied with each ANIM.
Installing the 9A656-04 Module 2-8.
3-1 Chapter 3 Operation The 9A656-04 provides switching between the fr ont panel interfaces (ANIMs) and the Cell T ransfer Matrix backplane located inside the SmartSwitch 9500 chassis.
Operation 3-2 A TM Cell T raffic Flo w in the 9A656-04 The 9A656-04 SmartSwitch utilizes several innovative features that r esult in a completely redundant, fault-tolerant design.
3-3 A TM Cell T raffic Flow in the 9A656-04 CTM (Cell T ransfer Matrix) ASICs The 9A656-04 has seven CTM ASICs that provide two interfaces each between the TDM Bus and the CTM Backplane located in the SmartSwitch 9500 chassis. Each interface is a full-duplex connection with a raw throughput capacity of 2 Gbps.
Operation 3-4 System Management Buses There ar e two management channels within the SmartSwitch 9500 system: ¥ SMB-1 ¥ SMB-10 These buses provide out-of-band management and inter -module management communication. SMB-1 Bus The SMB-1 is a 1 Mbps management bus located within the SmartSwitch 9500 chassis.
3-5 System Diagnostic Controller System Diagnostic Contr oller This diagnostic controller is composed of a Z-80 micr oprocessor and its supporting logic.
Operation 3-6.
4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figur e 4-1 are the LANVIEW LEDs of the 9A656-04 module. Refer to T able 4-1 for the full deÞnitions of 9A656-04 LED states.
LANVIEW LEDs 4-2 T able 4-1. SMB and CPU LEDs LED LED Color State DeÞnition SMB Green Functional Fully operational Amber Crippled Not fully operational (i.
4-3 ANIM LEDs The front panel LANVIEW LEDs indicate the status of the ANIM and may be used as an aid in troubleshooting. Shown in Figur e 4-2 are the LANVIEW LEDs of all ANIMs. Although there ar e several types of ANIMs, all share the same LANVIEW LEDs.
LANVIEW LEDs 4-4.
5-1 Chapter 5 General Specifications The speciÞcations for the 9A656-04 are detailed in the sections that follow . Operating Specifications En vironmental Requirements Operating T emperature 5¡C t.
General Specifications 5-2 Ph ysical Dimensions 35.0 D x 44.0 H x 3.0 W centimeters (13.8 D x 17.4 H x 1.2 W inches) W eight Unit: 1.36 kg. (3lb) Shipping: 1.
5-3 ANIM Specifications ANIM-21/3 The ANIM-21/3 provides a multimode Þber connection using a Duplex SC connector and a line rate of 155.52 Mbps. The speciÞcations for the ANIM-21/3 are listed in T able 5-1. Figure 5-1. ANIM-21/3 T able 5-1. ANIM-21/3 Specifications Parameter SpeciÞcation Number of Interfaces 3 Line Rate 155.
General Specifications 5-4 ANIM-29/3 The ANIM-29/3 provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-29/3 are listed in T able 5-2. Figure 5-2. ANIM-29/3 T able 5-2. ANIM-29/3 Specifications Parameter SpeciÞcation Number of Interfaces 3 Line Rate 155.
5-5 ANIM Specifications ANIM-29/3LR The ANIM-29/3LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-29/3LR are listed in T able 5-3. Figure 5-3. ANIM-29/3LR T able 5-3.
General Specifications 5-6 ANIM-31/2 The ANIM-31/2 provides a multimode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-31/2 are listed in T able 5-4.
5-7 ANIM Specifications ANIM-39/2 The ANIM-39/2 provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-39/2 are listed in T able 5-5.
General Specifications 5-8 ANIM-39/2LR The ANIM-39/2LR provides a single mode Þber connection using a Duplex SC connector with a line rate of 622 Mbps. The speciÞcations for the ANIM-39/2LR are listed in T able 5-6. Figure 5-6. ANIM 39/2LR T able 5-6.
5-9 ANIM Specifications ANIM-67/2 The ANIM-67/2 provides a coaxial cable connection using BNC connectors with a line rate of 45 Mbps. The speciÞcations for the ANIM-67/2 are listed in T able 5-7.
General Specifications 5-10 ANIM-77/2 The ANIM-77/2 provides a coaxial cable connection using BNC connectors with a line rate of 34 Mbps. The speciÞcations for the ANIM-77/2 are listed in T able 5-8.
5-11 ANIM Specifications ANIM-22/4 The ANIM-22/3 provides a Category 5 UTP connection using four RJ45 connectors with a line rate of 155.52 Mbps. The speciÞcations for the ANIM-22/4 are listed in T able 5-9. Figure 5-9. ANIM 22/4 T able 5-9. ANIM-22/4 Specifications Parameter SpeciÞcation Number of Interfaces 4 Line Rate 155.
General Specifications 5-12.
デバイスCabletron Systems 9A656-04 ATM Moduleの購入後に（又は購入する前であっても）重要なポイントは、説明書をよく読むことです。その単純な理由はいくつかあります：
Cabletron Systems 9A656-04 ATM Moduleをまだ購入していないなら、この製品の基本情報を理解する良い機会です。まずは上にある説明書の最初のページをご覧ください。そこにはCabletron Systems 9A656-04 ATM Moduleの技術情報の概要が記載されているはずです。デバイスがあなたのニーズを満たすかどうかは、ここで確認しましょう。Cabletron Systems 9A656-04 ATM Moduleの取扱説明書の次のページをよく読むことにより、製品の全機能やその取り扱いに関する情報を知ることができます。Cabletron Systems 9A656-04 ATM Moduleで得られた情報は、きっとあなたの購入の決断を手助けしてくれることでしょう。
Cabletron Systems 9A656-04 ATM Moduleを既にお持ちだが、まだ読んでいない場合は、上記の理由によりそれを行うべきです。そうすることにより機能を適切に使用しているか、又はCabletron Systems 9A656-04 ATM Moduleの不適切な取り扱いによりその寿命を短くする危険を犯していないかどうかを知ることができます。
ですが、ユーザガイドが果たす重要な役割の一つは、Cabletron Systems 9A656-04 ATM Moduleに関する問題の解決を支援することです。そこにはほとんどの場合、トラブルシューティング、すなわちCabletron Systems 9A656-04 ATM Moduleデバイスで最もよく起こりうる故障・不良とそれらの対処法についてのアドバイスを見つけることができるはずです。たとえ問題を解決できなかった場合でも、説明書にはカスタマー・サービスセンター又は最寄りのサービスセンターへの問い合わせ先等、次の対処法についての指示があるはずです。
